Kibi K1-SF27 Farmhouse Kitchen Workstation Sink Installation Guide
- June 17, 2024
- Kibi
Table of Contents
Kibi K1-SF27 Farmhouse Kitchen Workstation Sink
Installation
Handmade Stainless Steel Farmhouse Kitchen Sink
-
K1-SF27
-
K1-SF30
-
**K1-SF33
**
- **K1-SF36
**
- **K1-DF33
**
- K1-DF36
Installation
General Recommendations:
-
Read the instruction carefully before installation. Inspect the sink prior to installation to make sure that is not been
damaged during shipping. -
The instructions are for installation with solid surface and composite material countertops. KIBI recommends professional stone fabricator to perform the installation and is not responsible for damage to countertop or sink during installation.
-
Template are only provided as a guide. Place template on sink to ensure the template will give you the proper cutout for the sink.
-
Observe all local plumbing and building codes.
-
Keep this booklet and the receipt (or other proof of date and place of purchase) for this product in a safe place.
The receipt is necessary to request warranty parts. -
KIBI does not accept any liability for damage to countertop, sink fixture, faucets or personal injury during installation. Warranty is void if installation guide is not followed.
Please keep the box and packaging materials until your product is completely installed.
NOTE: These sinks are intended for indoor kitchen use only. They are not rated for outdoor use. Installation of this sink in an outdoor setting will void any warranty on this product.
Tools you may need
- **Drill
**
-
Jig Saw
-
**Pencil
**
- **Phillips Screwdriver
**
- **Screwdriver
**
- **Silicone sealant
**
-
Tape Measure
-
**Scissors
**
Determine Reveal Type
KIBI Farmhouse sinks can be installed in three different types:
1/8“ Negative Reveal
Flushed/Zero Reveal
KIBI Recommended installation type
3/8“ Positive Reveal
Caution: When determining sink placement, be sure to check that there is
adequate clearance behind the sink for any faucet(s) and your backsplash, as
well as clearance for a full range of motion for faucet spouts and handles.
NOTE: Contact your retailer if any product is damaged or missing prior to
installation. Never install a damaged sink as it can void your warranty.
Installation
-
Prepare the sink base cabinet. Measure the actual height of apron, Add 1/16” to the dimension when you mark base cabinet front cutout.
-
Build structural supports on the inside frame of the sink base cabinet. The structural supports must support the weight of the sink and any attachments such as garbage disposals.
-
Make template and cutout. Due to the various cutout sizes(based on your preference), A cutout template is not provided. Use the actual sink measurement to determine the actual location of the cutout. Ensure adequate clearance behind the sink for any faucet and backsplash.
-
Set the sink on top of the cabinet or into the cabinet front cutout. Apply sealant if necessary as a gasket between the sink and cabinet.
Do not use
epoxy. -
Carefully clean bottom of countertop and top edge of sink with denatured alcohol. Apply a bead of silicone adhesive (not supplied) around the top edge of the sink. Place countertop onto the sink.
-
Remove excess sealant from the lip of any surfaces with a cleaner recommended by manufacture of adhesive sealant.
Dimensions
K1-SF27 27”x22”x10” Min cabinet Size: 30”
K1-SF30 30”x22”x10” Min cabinet Size: 33”
K1-DF33 33”x22”x10” Min cabinet Size: 36”
K1-SF36 36”x22”x10” Min cabinet Size: 39”
K1-DF33 33”x22”x10” Min cabinet Size: 36”
K1-DF36 36”x22”x10” Min cabinet Size: 39”
Trouble-Shooting
If you’ve followed the instructions carefully and your sink still does not work properly, take these corrective steps.
Trouble – Shooting
PROBLEM| ACTION
Scratches| Use a nylon pad with an iron-free abrasive polishing compound.
Follow the direction of the original brush lines and the scratch will
disappear as it’s blended into the original finish. Be careful to not polish
too aggressively since you’ll polish out the original brush lines and end up
with a shiny spot.
Water deposits| Regular routine cleaning can usually prevent lime scale
deposits from hard water. Do not allow excessive build up before treating.
Soaking in a 25% vinegar solution or a 5% nitric acid solution can remove
these hard water spots. Periodically rub with a nylon-bristled brush or a
fine-mesh synthetic scouring pad. Rinse and towel dry after treatment.
Rust marks| If rust marks develop due to presence of, or contact with, ferrous
(iron-containing) materials, swab with a sponge wetted with a diluted (10-15%)
solution of nitric acid (HNO3) and follow with routine cleaning. Avoid
prolonged contact of ferrous materials (like cast iron pans) with stainless
steel. Nitric acid in dilute concentrations (<20%) is the only acid that is
safe to use on stainless steel.
Care & Maintenance
Clean regularly with normal detergent and warm water.
Always make a habit of drying your sink after use and buffing with a soft
cloth. This will ensure that no build up of limescale or other mineral
deposits can occur.
Clean the sink once a week using a non-abrasive cleanser such as Comet and a
clean soft sponge. Scrub in the same direction as the natural grain of the
sink.
Never let soap or other household cleaners to dry on the surface of the sink.
Most products contain addatives which will affect the finish of the sink.
Never use bleach solutions on the sink, as it is harmful to stainless steel.
If left on the sink too long it can cause surface pitting.
Never use a steel wool pad to clean your sink. Doing so may damage the sink’s
surface and cause discoloration.
Minor scratching of the sink’s surface is extremely difficult to avoid and is
not something to be unduly concerned about.
These marks are usually only superficial and can be removed with a proprietary
stainless steel cleaner.
Use of rinse grids will reduce exposure of the bottom of the sink to
scratches.
Limited Lifetime Warranty
This product has been manufactured and inspected to the highest possible
quality standards. Kibi sinks carry a limited lifetime warranty for
residential use.
Should you experience any defects in materials or workmanship within the
warranty period, we will repair or replace the defective product, subject to
the following conditions:
-
Any claim made under this warranty must include a copy of a valid proof of purchase showing the date and place of purchase.
-
Our obligation under this warranty is to the original purchaser only, and may not be transferred.
-
Product replacement does not include shipping costs or labor installation costs.
-
This warranty applies to residential installations only.
-
Kibi reserves the right to examine product in question and its installation prior to replacement.
-
If an identical replacement product is not available, Kibi reserves the right to replace the defective product with a similar product.
NOTE: Accessories such as rinse grids, cutting boards, strainers are not covered by this warranty.
This warranty relates to defects in manufacture, materials or workmanship in a Kibi stainless steel kitchen sink supplied for installation into domestic premises in the United States. It does not extend to : -
Damage resulting from failure to maintain the product in accordance with the Care and Maintenance instructions in this manual.
-
Normal wear and tear, scratches or accidental damage.
-
Faults arising from improper use and/or installation.
-
Defects in accessories, strainers and rinse grids.
All incidental or consequential damages are specifically excluded. No additional warranties, express or implied are given, including but not limited to, any implied warranty of merchantability or fitness for a particular purpose.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above limitations or exclusions may not apply to you.
This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>