duravent 3VP-60B Pellet Vent Catalog Instruction Manual

duravent 3VP-60B Pellet Vent Catalog

MINIMUM CLEARANCE TO COMBUSTIBLES

Selkirk® VP Pellet Pipe™ may be installed with a minimum 1″ airspace clearance to combustible surfaces, such as framing lumber, drywall, plywood, or other building materials. VP Pellet Pipe™ may be exposed in occupied areas and painted pipe lengths help make your venting system an attractive accent to your interior decor.

However, your venting system should be enclosed whenever it passes through closets, storage rooms, or accessible attics to ensure that the minimum 1″ airspace clearance is maintained. This is particularly true in attics where cellulose-type or other blown-in Insulation materials could settle against the exposed vent pipe.

It is also advisable to provide an enclosed chase for exterior vent systems to aid in reducing condensation and protect the pipe from cold outdoor temperatures. VP Pellet Pipe™ features a proven joint design that allows for easy assembly. Special rope gaskets incorporated into the joint reduce leakage and help to minimize any accumulation of combustion powder residues.

In addition, VP Pellet Pipe™ is listed for use with an optional, high- temperature silicon sealant which enhances the integrity of the joint assembly. Selkirk® is the world’s leading manufacturer of venting and air distribution products for residential, commercial, and industrial use. VP Pellet Pipe™ vent for pellet stoves is just one of the family of fine products sold worldwide. Selkirk® – it’s a name you can rely on.

TYPICAL VP PELLET PIPE INSTALLATIONS

The following illustrations show the most common types of Model VP installations and the variety of parts required.

Horizontal Exit Termination

Through the Ceiling Rear Vent

Note: Always follow appliance manufacturer instructions for minimum vertical requirements.

Through the Wall Installation

Through the Wall Rear Vent

Selkirk® gives you a safe, efficient, and cost-effective venting system that’s engineered precisely for pellet-burning stoves. Model VP Pellet Pipe has been tested and listed by Underwriters’ Laboratories, Inc., by UL-641, CAN/ULC-S609 Standard for Low-Temperature Venting Systems, as well as the applicable requirements from UL-103 Standard for Residential Type and Building Heating Appliance Chimneys.  VP Pellet Pipe, when installed according to Selkirk’s installation instructions, complies with National Safety Standards, such as NFPA -211 in the US and CSA/B365 in Canada. The system is rated for flue temperatures up to 570°F.

• Available in 3″ and 4″ diameters.
• A full line of fittings and a full range of pipe lengths increase installation flexibility.
• Proven coupling joint connects in seconds to assure joint integrity.
• Gasketed joint design.
• Painted pipe lengths are available for interior use.
• Double wall design with ¼” airspace.
• The inner wall is 304 stainless steel, outer wall is paintable galvanized.
• Rolled-over male end eliminates sharp edges.
• 1″ clearance to combustibles. Clearances in Canada are 3″.
• Removable tee cap for inspection and cleaning.
• Internal spacing bead assures uniform insulating airspace between pipe walls.

VENT PIPE AND ADJUSTABLE PIPE LENGTHS

I.D.: 3″, 4″

• Lengths: 6″, 1′, 2′, 3′, 5′
• VP pipe & fittings overlap 1-½” when joined hence, the net assembled length is 1-½” less than the listed lengths (3′ and 5′ lengths available in black)

I.D.: 3″, 4″

• Max. installed length 10-½”
• Adjusts to 8″ shorter
• (Black or Unpainted)

Pellet Pipe Lengths

• Available in lengths of 5′, 3′, 2′, 12″ and 6″.
• Available in galvanized and black.

Adjustable Pipe Length

• Adjustable length eliminates the need to cut pipe.
• Adjustable length simply slides over another VP length.

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
5′ Length – Black| 243060B| 3VP-60B| 244060B| 4VP-60B
5′ Length| 243060| 3VP-60| 244060| 4VP-60
3′ Length – Black| 243036B| 3VP-36B| 244036B| 4VP-36B
3′ Length| 243036| 3VP-36| 244036| 4VP-36
2′ Length| 243024| 3VP-24| 244024| 4VP-24
12″ Length| 243012| 3VP-12| 244012| 4VP-12
6″ Length| 243006| 3VP-6| 244006| 4VP-6
12″ EZ Adj. – Black| 243086B| 3VP-EZAJ12B| 244086B| 4VP-EZAJ12B
12″ EZ Adj.| 243086| 3VP-EZAJ12| 244086| 4VP-EZAJ12

Tee

• Used to transition from horizontal to vertical orientation.
• Provides easy access for inspection and maintenance.
• Includes Tee Cap.

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Tee w/Tee Cap – Black| 243100B| 3VP-TSB| 244100B| 4VP-TSB
Tee w/Tee Cap| 243100| 3VP-TS| 244100| 4VP-TS
Double Tee w/2 Caps| 243103| 3VP-TD| 244104| 4VP-TD
Increaser Tee|  |  | 244113| 4VP-3T
Increaser Tee – Black|  |  | 244113B| 4VP-3TB
Tee Cap|  | 3VP-TC|  | 4VP-TC

Double Tee

• Provides access to the clean horizontal portion of the chimney system.
• Includes 2 Tee Caps.
• Replaces Pipe Connector, 3″ – 4″ Increaser and 4″ Tee.
  4″Diameter

Item Description Product No.      Part No.

4 x 3 Adjustable Tee w/Tee Cap| 244133B| 4VP-3AT

• Used to orient pipe between vertical and horizontal orientation.
• Factory sealed at couplers to prevent leakage.
• Used to offset pipe around construction obstacles.
• Factory sealed at couplers to prevent leakage.

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
90° Elbow – Black| 243231B| 3VP-90°ELB| 244230B| 4VP-90°ELB
90° Elbow| 243230| 3VP-90°EL| 244231| 4VP-90°EL

TEES AND DOUBLE TEES W/ TEE CAP

4 X 3 ADJUSTABLE TEE W/TEE CAP

90º ELBOW

45° ELBOW

CEILING SUPPORT / FIRESTOP

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Ceiling Support/ Firestop| 243410| 3VP-CS| 244410| 4VP-CS

WALL BRACKET / SUPPORT

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Wall Bracket/ Support| 243520| 3VP-WB| 244520| 4VP-WB

TEE SUPPORT

3″ / 4″Diameter

Item Description Product No.      Part No.

Tee Support| 243430| 3/4VP-WS

CATHEDRAL CEILING SUPPORT

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Cathedral Ceiling Support| 243424| 3VP-CCS| 244424| 4VP-CCS

Pellet Pipe Supports

• Used to support pipe from the ceiling joist.
• Maintains clearance of combustibles.
• Designed to provide both lateral and vertical support for vent pipe when installed adjacent to a wall.
• Can be used to stabilize the pipe against an outside wall.
• Install on the first pipe length above a Tee if optional Tee Support is not used.
• Maintains 3″ clearance to combustibles.
• Two plates are used to stabilize and support the Tee.
• Used in cathedral-style installations.
• Painted black for a decorative finish.
• Includes a two-part square black Trim Plate.
• Includes a Support Band.

Product No. Part No.

284855| 4VP-25IK
Product No. Part No.

284865| 4VP-35IK

Pellet Pipe Kits

4″ Pellet Pipe Flex Kit has the following:

• 25′ of 4″ Diameter Stainless Flex
• 4″ Flex Termination
• 4″ Flex Flashing Adapter
• 4″ Flex Flashing
• 3 – 4″ Increaser
• 3″ Pipe Connector
• Silicone sealant
• 4″ Pull Down Tool
• 4″ Flex to Pellet Pipe Adapter

4″ Pellet Pipe Flex Kit has the following:

• 35′ of 4″ Diameter Stainless Flex
• 4″ Flex Termination
• 4″ Flex Flashing Adapter
• 4″ Flex Flashing
• 3 – 4″ Increaser
• 3″ Pipe Connector
• Silicone sealant
• 4″ Pull Down Tool
• 4″ Flex to Pellet Pipe Adapter

PELLET PIPE INSERT (FLEX) KITS
The 3VP Thru-the-Wall Pellet Kit has the following:

• 1 – 3″ Horizontal Cap
• 1 – 3″ 90° Elbow
• 1 – 3″ Wall Bracket
• 5 – 3″ One-foot Pipe Lengths
• 1 – 3″ Tee with Cleanout
• 1 – 3″ Wall Thimble
• 1 – 3″ Pipe Connector
• 1 – 3″ Tee Support

The 3/4VP Thru-the-Wall Pellet Kit has the following

• 1 – 4″ Horizontal Cap
• 1 – 4″ 90° Elbow
• 1 – 4″ Wall Bracket
• 5 – 4″ One-foot Pipe Lengths
• 1 – 4″ Tee with Cleanout
• 1 – 4″ Wall Thimble
• 1 – 4″ Tee Support
• 1 – 3″ to 4″ Increaser
• 1 – 4″ Pipe Connector
• 1 – 3″ Pipe Connector

THRU-THE-WALL PELLET STOVE KITS

STORM COLLAR

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Storm Collar| 243810| 3VP-SC| 244810| 4VP-SC

HORIZONTAL AND VERTICAL TERMINATIONS

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Vertical Termination| 243800| 3VP-VC| 244800| 4VP-VC
Horizontal Termination| 243805| 3VP-HC| 244805| 4VP-HC

EXIT CAP AND SCREENS

Rain Caps and Collars

• Used to provide a weatherproof seal to pipe above roof flashing.
• Seal the inner edge with hi-temp silicone sealant.
• Vent Termination for horizontal (thru-the-wall) installations.
• Vent Termination for vertical (thru-the-roof) installations.
• Designed to prevent rain & snow from entering the pipe.
• Used with Horizontal installations.

Pellet Pipe Flashings

• Used to waterproof installations through a flat roof.
• Used to waterproof installations that penetrate the roof line.

Pellet Pipe Shields

• The attic insulation shield is required to guard against the hazard of blown-in or blanket insulation occupying the required 1″ air space around the vent.
• Used in Thru-the-Wall installations.
• Maintains airspace clearance.
• Centres pipe between walls.
• Telescopic design can be used on standard walls – WT: 4″ – 7″ WTT: 6.5″ – 11.5″

TALL CONE FLASHING

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Tall Cone Flashing| 243815| 3VP-TF| 244815| 4VP-TF

ADJUSTABLE FLASHING

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Adj. Flashing| 243825| 3VP-AF| 244825| 4VP-AF

ATTIC INSULATION SHIELD

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Attic Insulation Shield| 243490| 3VP-AIS| 244490| 4VP-AIS

WALL THIMBLE

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Wall Thimble| 243460| 3VP-WT| 244460| 4VP-WT
Wall Thimble, Thick| 243461| 3VP-WTT| 244461| 4VP-WTT

TRIM PLATE AND EXTERIOR SHIELD

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Trim Plate – Black| 243502| 3VP-TP| 244502| 4VP-TP
Exterior Shield| 243500| 3VP-ES| 244500| 4VP-ES

SELKIRK UNIVERSAL SHIELDING INSULATION (SUSI)

3″ TO 4″ INCREASER

PIPE CONNECTOR

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Pipe Connector| 243240| 3VP-PC| 244240| 4VP-PC
Pipe Connector – Black| 243240B| 3VP-PCB|  |
Multi-Fit Connector| 243241| 3VP-MFC|  |
Adjustable Pipe Connector| 243243| 3VP-APC| 244243| 4VP-APC

ADJUSTABLE PIPE CONNECTOR

Item Description

| 3″Diameter Product No. Part No.| 4″Diameter Product No. Part No.
---|---|---
Adjustable Pipe Connector| 243243| 3VP-APC| 244243| 4VP-APC

Pellet Pipe Accessories

• Used to adapt 3″ pipe to 4″ pipe.
• For connection to appliance outlet collar.
• Used to accommodate a wider range of 3″ or 4″ flue collar variances for a better fit.

Pellet Pipe Accessories continued

• Connects 3″ flue collar to 4″ VP parts.
  Item Description| Product No.| Part No.
  ---|---|---
  Multi-Fit Connector| 243241| 3VP-MFC

• Used on appliances with a thicker flue outlet collar.

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Thick Collar Pipe Connector| 243242| 3VP-TPC| 244242| 4VP-TPC

MULTI-FIT CONNECTOR

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
6″ Chimney Adapter| 243246| 3VP-A6| 244246| 4VP-A6
8″ Chimney Adapter| 243248| 3VP-A8| 244248| 4VP-A8

THICK COLLAR PIPE CONNECTOR

Item Description

| 3″Diameter

Product No. Part No.

| 4″Diameter

Product No. Part No.

---|---|---
Vacuum Cleanout Cap| 243185| 3VP-VCC| 244185| 4VP-VCC
Tee Cap| 243180| 3VP-TC| 244180| 4VP-TC

CHIMNEY ADAPTER

VACUUM CLEANOUT CAP

Installs on a base of Tee and replaces Tee Cap. Tee sold separately. 2023 Duravent Group. All rights reserved. SK_VPP_CT-001-US-E_05-23

References

• Duravent Group
• Selkirk

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>