Maglocks FPR-200W Fingerprint Access Control User Manual

Maglocks FPR-200W Fingerprint Access Control User Manual

Introduction

The series of product is a new generation of multi-functional standalone access control. It adopts
new ARM core 32-bit microprocessor design, which is powerful, stable and reliable. It contains
reader mode and standalone access control mode etc.. It’s widely applied to different occasions, such as office, residential communities, villa etc..

Features

Read 13.56MHz Mifare card and CPU card (Optional)
Keypad Characteristic| Operate by infrared remote
Output Way| Contain reader mode, the transmission format could be adjusted by users
Access W| Support multi access ways: Card+Fingerprint, multi cards or multi fingerprints
Admin Card/Fingerprint| Support admin card/admin fingerprint
User Capacity| 10,000 card users and 300 fingerprint users
Unlocking Signal| Relay NO/NC/COM output

Technical Specifications

• Operating Voltage: DC 12-24V: Standby Current: ≤ 35mA
• Operating Current: ≤100mA : Operating Temperature: -20℃~60℃
• Operating Humidity: 0%~95%: Electric lock signal relay contact current：≤1A
• Alarm signal MOS tube output current: ≤1A : Unlocking time: 0~300s adjustable

Installation

• Remove the back cover from the keypad using the supplied special screw driver
• Drill 2 holes on the wall for the self-tapping screws and hole for the cable
• Put the supplied rubber bungs to into the two holes
• Fix the back cover firmly on the wall with 2 self-tapping screws
• Thread the cable through the cable hole
• Attach the keypad to the back cover. (as following illustration)
  

Wiring

(optional)
6| Red| +12V| Positive power supply
7| Black| GND| Negative power supply
8| Blue| NO| Relay NO end
9| Purple| COM| Relay COM end
10| Orange| NC| Relay NC end

Diagram

Common Power Supply

Note: The door contact and alarm function are optional

Special Power Supply

Note: The door contact and alarm function are optional

**Reader Mode

**

Sound and Light Indication

Admin Menu

Standalone Mode Settings

Device Management

=| Menu| Operation steps| Description| Default value|
---|---|---|---|---|---
| 0| New admin code # new admin code #| Change admin code| 999999|
* Press Admin code #| ** 1| 10001# Read card / Input a fingerprint twice | Set admin add card or admin add fingerprint| |
10002# Read card / Input a fingerprint twice | Set admin delete card or admin delete fingerprint| |
(Default admin code is “999999”)|
*** 2| 10001# | Delete admin add card or admin add fingerprint| |
10002# *| Delete admin delete card or admin delete fingerprint| |
| | 11 #| Standalone access control mode| |
| 3| 12 #| Relay toggle mode| 11|
13 #| Reader mode|
| | ( 26-58 ) #| Wiegand 26-58 bits output|
8| 8 #| WIFI matching| Optional|

Add and Delete Users

• Read admin add card / Input admin add fingerprint
  

• Read the 1st user card / Input the 1st fingerprint twice
  

• Read admin add card / Input admin add fingerprint
  

• Read the 2nd user card / Input the 2nd fingerprint twice

Note： The admin add card / admin add fingerprint is used to add card / fingerprint users
continuously and quickly. When you read the admin add card / input the admin add fingerprint
at the first time, you will hear short “BEEP” sounds twice and the indicator light turns orange, it
means you have entered into add user programming, when you read the admin add card / input
the admin add fingerprint at the second time, you will hear long “BEEP” sound once and the indicator light turns red, it means you have exited the add user programming.

Delete Users

• Read admin delete card / Input admin delete fingerprint
  

• Read the 1st user card / Input the 1st
  

• fingerprint twice
  

• Read the 2nd user card/ input the 2nd fingerprint once
  

• Read admin delete card

Note： The admin delete card / admin delete fingerprint is used to delete card / fingerprint users
continuously and quickly. When you read the admin delete card / admin delete fingerprint at the
first time, you will hear short “BEEP” sounds twice and the indicator light turns orange, it means
you have entered into delete user programming, when you read the admin delete card / admin
delete fingerprint at the second time, you will hear long “BEEP” sound once, the indicator light
turns red, it means you have exited the delete user programming.

Other Operation

Remove Alarm

• Read valid card
  

• Input valid fingerprint
  

• Press admin code#

Note： When the alarm is activated, users can remove the alarm by reading a valid card or inputting valid fingerprint or pressing valid admin code.

Reset to Factory Default

Users can reset to the factory default when the admin code is forgotten, or the default settings
have been modified disorderedly, operations as below:
Power off, press and hold the exit button continuously, power on, release the exit button until hearing beep sound twice, the admin code has been reset to 999999, factory default settings are successful.

Note: Registered user data won’t be deleted when reset to factory default.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>