FrSky Neuron II 60 Fixed Wing ESC Instruction Manual
- June 17, 2024
- Frsky
Table of Contents
FrSky Neuron II 60 Fixed Wing ESC
Specifications:
- Continuous Current: 60A
- Input Voltage: 3S-6S (11.2V-25.2V)
- BEC: Configurable 10A @ 5V-8.4V
- Case Material: All-CNC Machined Aluminum
- Dimensions: 15.2mm x 34mm x 59mm
Product Information:
The FrSky Neuron II 60 ESC offers a range of features and capabilities for
various applications. With telemetry data transmission, all-CNC machined
aluminum casing for heat dissipation and support for different signaling
inputs, this ESC provides high performance and reliability.
Connection Diagram:
Product Usage Instructions
Initial Setup:
Connect the Neuron II 60 ESC to your motor, receiver, and power supply
following the provided connection diagram. Ensure proper wiring connections.
Parameter Configuration:
To configure parameters, you will need the STK tool (sold separately).
Connect the STK tool to your computer and power supply, then access the web-
based configurator within 5 seconds of powering the ESC.
Web-Based Configuration:
Visit the web-based ESC configuration page and access features like
reversing motor direction and adjusting other settings based on your needs.
Introduction
Based on the performance and design features of the first-gen NEURON ESC
products, the NEURON II line steps it up by offering a broader selection of
ESC models to various demands in different applications.
The NEURON II 60 comes with a fully enclosed all-CNC machined aluminum casing
design, ensuring efficient heat dissipation while handling a continuous
current of 60A. The NEURON II series can transmit telemetry data from built-in
sensors to the radio by the receiver, allowing users to get real-time insights
right from the radio system. RPM, power consumption, temperature, input/output
voltage, and current readings are all at your fingertips.
With added support for the FBUS protocol, the NEURON II takes convenience to a
whole new level! Users can now easily configure the BEC output voltage and
other ESC parameters directly from the transmitter via the receiver. Or with
even more flexibility, hook up NEURON II ESC to the ETHOS radio’s S.Port for
seamless wired configuration without requiring a receiver (this feature will
be available on ETHOS 1.5.0 and later versions). The traditional configuration
method through a PC webpage is also retained. There’s more! The NEURON II
60/80 comes with support for multiple signaling protocols which can be used to
drive and configure a wide range of compatible motors.
Overview
Specifications
- Dimension: 59×34×15.2mm(L×W×H)
- Weight: 75g (with wires included.)
- Battery Input Voltage Range: 11.2-25.2V (3S-6S Li batteries)
- BEC Output Voltage Range: 10A@5V~8.4V (Adjustable & Voltage Step 0.1V)
- Power Connector for BEC: JST
- Continuous Current: 60A
Features
- All-CNC Machined Aluminum Case aiding in Heat Dissipation
- Various Telemetry Data (for ESC & SBEC) via FBUS / S.Port
- – Telemetry data for ESC: Batt Voltage & Current (Resolution 125mA, Precision ±2%), RPM, Power Consumption, Temperature.
- – Telemetry data for SBEC: Output Voltage & Current (Resolution 50mA, Precision ±2%).
- Adjustable SBEC Output Voltage & ESC Parameters by LUA scripts (on ETHOS, OPTX radios.) or PC Configuration Webpage (by STK tool)
- Supports Various Signaling Inputs for Motor Control (PWM, DShot, OneShot)
- High-Performance32-bit Microprocessor
- Over-Temperature and Over-Current Protection
Connection Diagram
Parameter Configuration ( PC Webpage Programming via STK tool )
The FrSky ESC Neuron II 60 supports editing parameters through the STK
tool. The STK tool is not included in the packaging and needs to be purchased
separately by the user.
Note : To configure the Neuron II ESC, please connect the STK tool to your computer and connect the power supply to the Neuron II ESC. Once powering the ESC then, please click the “Connect” button on Webpage Configurator in 5 seconds to complete the connection.
The configuration methods provided below are for reference only. Due to
firmware updates or other reasons, the functionality description may vary.
Please refer to the latest official user manual for accurate configuration
instructions.
Here are the descriptions of various features on the web-based ESC
configuration page of FrSky Neuron II.
- Reverse motor direction: This feature allows you to control whether the motor spins in the opposite direction. Checking this option will reverse the motor direction.
- Slow start: It controls the gradual acceleration of the motor during startup to avoid sudden and strong reactions.
- Soft start: This feature enables a smooth acceleration of the motor during startup, reducing the impact force and load on the motor.
- ESC beeps: It determines whether the ESC emits audible beeps during startup, serving as an indicator of its status.
- PWM Min: This setting determines the minimum PWM signal value that the ESC will recognize as the lowest throttle position.
- PWM Max: It sets the maximum PWM signal value that the ESC will recognize as the full throttle position
- Soft brake: This feature controls whether the ESC implements a smooth braking action when transitioning to low throttle.
- 3D Mode: It activates a special mode in the ESC suitable for performing aerobatic maneuvers and 3D flight actions.
- Current calibration(%): This option allows you to calibrate the ESC to accurately measure current, providing precise current data.
- Current limit: It lets you set the maximum current output limit of the ESC to protect both the ESC and the motor from overloading.
- BEC output Voltage: You can specify the output voltage of the ESC’s built-in BEC (Battery Eliminator Circuit).
- Activated: Display ESC Activation Status.
- Trapeziodal commutation
- Physical ID: This setting specifies the physical ID used for communication.
- Application ID: This setting specifies the Sensor ID used for communication.
- Response Time(*100ms): It determines the time gap between communications.
- High demag. protection
- Motor pole count: It refers to the number of magnetic poles inside the motor. You need to set the correct pole count to ensure proper motor rotation and ESC commutation.
- Throttle channel: Specify the serial port signal channel for the throttle channel input signal used to control the ESC, such as SBUS/FBUS.
- OneWire ID: This feature assigns a unique ID to each ESC when using OneWire bus communication.
These features offer a wide range of configuration options to meet the requirements of different types of aircraft and flight preferences. Specific features and options may vary based on the version of FETtec Configurator and device support. Please consult the relevant documentation or official guides for more detailed information before using these options.
Parameter Configuration ( ETHOS Lua Programming via FBUS / S.Port )
Here are the descriptions of various features on the ETHOS LUA configuration page of FrSky Neuron II ESC.
This feature allows you to control whether the motor spins in the opposite
direction. Checking this option will reverse the motor direction.
Use Sine Wave Start
This feature enables a smooth acceleration of the motor during startup,
reducing the impact force and load on the motor.
It determines whether the ESC emits audible beeps during startup, serving as an indicator of its status.
This setting determines the minimum PWM signal value that the ESC will recognize as the lowest throttle position.
It sets the maximum PWM signal value that the ESC will recognize as the full throttle position.
This feature controls whether the ESC implements a smooth braking action when transitioning to low throttle.
It activates a special mode in the ESC suitable for performing aerobatic maneuvers and 3D flight actions.
This option allows you to calibrate the ESC to accurately measure current, providing precise current data.
It lets you set the maximum current output limit of the ESC to protect both the ESC and the motor from overloading.
You can specify the output voltage of the ESC’s built-in BEC (Battery Eliminator Circuit).
Trapeziodal commutation
This setting specifies the physical ID used for communication.
This setting specifies the Sensor ID used for communication.
It determines the time gap between communications.
It refers
to the number of magnetic poles inside the motor. You need to set the correct
pole count to ensure proper motor rotation and ESC commutation.
Specify the serial port signal channel for the throttle channel input signal used to control the ESC, such as SBUS/FBUS.
High demag. protection
Here is the telemetry sensor configuration and feedback for the ETHOS system.
Warnings
Before using the ESC, please read through the manuals of all power devices
and models. Ensure rational power configuration, or it will make the unit
overloaded and damaged.
- Always keep your model away from unsafe elements, such as concrete buildings and high-voltage power lines. Fly your models according to the manual strictly, or it may cause damage and serious injuries.
- Always disconnect the batteries from the ESC after use, or it may drive the motor to rotate and cause injuries. If the ESC is connected to the battery for a long time, the battery will be fully discharged, which may lead to the malfunction of both batteries and the ESC.
Firmware Upgrade for NEURON2 ESC
- Configuration Device: STK Tool (Separate Purchase Required)
- Webpage Configurator: https://gui.fettec.net/FrSky/ESC/
Step 1 :
Connect the STK tool to the PC, and select the “USB UART” port on the
Configurator webpage.
Step 2:
A connecting request window prompts up at this moment and then click the
“Connect” button.\
Step 3:
Connect the NEURON2 ESC to the S.Port 2 and switch the Dip to “Upgrade” mode.
Once powering the ESC then, please click the “Connect” button in 5 seconds to
complete the connection.
Step 4：
Click the “Local Firmware” button and find the path of the firmware to update
the ESC.
Step 5:
Click the tab “Flash selected” waiting for the completion of the flashing bar. A prompt of the “Warning” window means the flash is done.
- FrSky Electronic Co., Ltd. www.frsky-rc.com
- Contact us: frsky@frsky-rc.com
- Add: F-4, Building C, Zhongxiu Technology Park, No.3 Yuanxi Road, Wuxi, 214125, Jiangsu, China
- Technical Support: sales4tech@gmail.com
FAQ
Q: What is the input voltage range for the FrSky Neuron II 60 ESC?
A: The ESC supports input voltages from 3S to 6S, ranging from 11.2V to
25.2V.
Q: How can I reverse the motor direction using the web-based configurator?
A: In the web-based configurator, there is an option to reverse the motor
direction. Simply check the corresponding box to reverse the motor spin.
References
- Robinson+Cole
- FrSky Top Rated RC Hobby Radio, Receiver and RC Model - Lets you set the limits
- FETtec Configurator
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>