SOUNDEXTREME SEI-SELEDZ4 4 Zone LED Controller User Guide
- June 17, 2024
- SoundExtreme
Table of Contents
SEI-SELEDZ4 4 Zone LED Controller
Specifications
- Model: SEI-SELEDZ4
- Type: 4-Zone LED Controller
- Power Input: 12V
- Connection: Vehicle Signal Input Connectors
- Control Outputs: Zone 1, Zone 2, Zone 3, Zone 4
Product Information
ExtremeController Overview
The ExtremeController is a 4-Zone LED Controller designed to
enhance your vehicle’s lighting capabilities. It features multiple
output connectors and vehicle signal input connectors for seamless
integration with your vehicle’s lighting system.
Layout
The layout includes Connection Status LED Indicator,
Multifunction Button, Vehicle Signal Input Connectors, and LED
Control Output Connectors for each zone.
Product Usage Instructions
Connection and Setup
-
Attach the 8ft Power Cable to the 12V Power-In SAE
Connector. -
Ensure proper connection to the vehicle’s left turn, right
turn, brake, and reverse lighting signals. -
Connect the Remote Turn-On Wire to the appropriate
connector.
Installation Steps
-
For Gas Vehicles:
-
Loosen the bolts on the battery terminals and connect the wires
accordingly. -
Tighten the bolts securely and insert the fuse back into the
holder. -
For Electric Vehicles: Follow similar steps for connecting to
the power source.
Multifunction Button
The Button has three functions:
-
Short-Press: Re-enable EcoCast audio pairing for LED Music
Mode. -
Long Press: Clears the EcoCast pairing records.
FAQ
Q: What do the different LED indicators signify?
A: Flashing Blue indicates Remote Control Pairing Mode, Flashing
Green means searching for an EcoCast Transmitting device, and Solid
Green implies connection to an EcoCast Transmitting device.
Q: Can I use the controller without connecting it to the
vehicle’s signaling system?
A: While it’s optional, connecting to the vehicle’s signaling
system enables advanced lighting features like enhanced brake,
reverse, and turn signals.
ExtremeController
Model: SEI-SELEDZ4
4-ZONE LED CONTROLLER
User Guide
Introduction
· Please read the User Guide before installation and use.
· The ExtremeController is compatible with the ECOXGEAR audio and LED lighting
EcoSystem, which includes LEDCast and EcoCast Innovations. Look for the
LEDCast and EcoCast logos on the growing family of ECOXGEAR and SoundExtreme
audio and lighting solutions.
· The ExtremeController has four Zone LED Control Outputs. Each Zone supports
a maximum power output of 5A. Thus, the total current consumption on the power
supply to the ExtremeController depends on how many LEDs are connected to the
controller. The maximum current draw is 20A if four 5A units are connected to
the controller AND are all lit up at the same time.
· Please refer to specifications of your SoundExtreme LED product when you
analyze the current-draw requirements of your power supply.
· The voltage for the power input is +12VDC. You need to connect to a 12VDC
power supply. If your vehicle battery power is not 12V (e.g., 24V, 36V, or
48V), you will need a DC-DC voltage converter with 12V output (e.g. a 48V-to-
12V converter). Connecting the ExtremeController directly to higher voltages
will cause damage to the controller and VOID THE PRODUCT WARRANTY.
· The ExtremeController has a Remote Turn-On Input feature; this is to ensure
that the controller is completely powered off (no battery consumption) when
your vehicle is not in use. When the input has a signal between 12V to 56V,
the controller will turn on. When there is no input voltage, the controller
will turn off. In general, this Remote Turn-On signal comes from the vehicle
ignition switch.
· The ExtremeController has 4 Vehicle Signal Inputs (left turn, right turn,
brake, and reverse). When you connect the controller to these inputs, only LED
products that are connected to Zones 3 and 4 will be affected. If you are not
sure where these signal wires are located on your vehicle, consult your
vehicle’s manual
2
Introduction
or a technician. Incorrect connections to your vehicle may cause your
controller or your vehicle to malfunction. Please note that the maximum
voltage for these 4 Vehicle Signal Inputs is 12VDC. · The ExtremeController
can be controlled by the included RF Remote or a free SoundExtreme Smartphone
App available on the Apple App Store and Google Play Store. · The
ExtremeController can support multiple types of SoundExtreme LED products. All
4 Zones come preset to the 6 ExtremeWhip. To optimize the LED light
performance the first time you use the controller, or you make LED Zone
connection changes after the initial set up, please use the SoundExtreme
Smartphone App to choose the LEDCast product that is connected to each Zone. ·
The ExtremeController Music Modes work with ECOXGEAR or SoundExtreme products
with EcoCast wireless capability. When an LED Zone output is set to Music
Mode, the controller needs to wirelessly connect to an EcoCast-enabled audio
product. · Do NOT make modifications to the ExtremeController LED connectors
or try to connect this product to other manufacturers’ LED products. It may
cause permanent damage to the product and VOID THE PRODUCT WARRANTY.
3
ExtremeController Overview
ExtremeController Layout
Connection Status LED Indicator
Multifunction Button
Vehicle Signal Input Connectors: Left Turn, Right Turn, Brake, Reverse
Zone 4: LED Control Output Connector (Right)
Zone 3: LED Control Output Connector (Left)
Zone 2: LED Control
Power Inputs:
Output Connector
12V Power-In SAE Connector, Zone 1: LED Control
Remote Turn-On Wire (Dark Blue) Output Connector
4
ExtremeController Overview
Button & Connectors
8ft Power Cable
12V Power-In SAE Connector
Fuse Holder
10ft Remote Turn-On Extension Cable
Remote Turn-On Wire
Power Input Connector: Power-In SAE Connector (+12V and GND), Remote Turn-On Wire (Dark Blue).
· The Power-In SAE cable has an in-line 25 Amp Fuse Holder.
· Also included are an 8ft SAE Power Cable and a 10ft Remote Turn-On Extension
Cable (Dark Blue).
Vehicle Signal Input Connectors: Left Turn, Right Turn, Brake, Reverse
Vehicle Signal Input Connectors: Connect to the vehicle for left turn, right
turn, brake, and reverse lighting integration. (This connection is optional;
however, you won’t be able to use the Vehicle Signaling Features on your LED
product without it.)
Multifunction Button: The Button has 3 functions.
1. Short-Press: Re-enable EcoCast audio pairing for LED Music Mode. 5
ExtremeController Overview
2. Double-Click: Enable RF Remote Control pairing. · The included Remote
Control already comes paired and is
automatically connected to the ExtremeController. · This feature is meant to
be used if the connection is lost or a
replacement Remote Control is purchased. 3. Press and Hold for 3 seconds:
Clears the EcoCast pairing records. Connection Status LED Indicator: The LED
indicates 3 possible Connection Statuses. 1. Flashing Blue: The
ExtremeController is in Remote Control
Pairing Mode. 2. Flashing Green: The ExtremeController is searching for an
EcoCast Transmitting device to pair and connect to. 3. Solid Green: The
ExtremeController is connected to an EcoCast
Transmitting device.
LED Control Output Connectors
LED Control Output Connectors: Connect SoundExtreme LED products to each of
the 4 Zone Control Outputs. · All 4 Zone Outputs have the same electric
specifications. · Only Zones 3 and 4 integrate with the Vehicle Signal Inputs,
allowing the connected LEDs to function as enhanced brake, reverse, and turn
signal lights. 6
Installation and Wiring
Connecting to 12VDC Power Supply
The ExtremeController does not have an internal battery. It must be connected
to an external 12VDC power supply to function. When you install the
ExtremeController to a battery or a voltage regulator on a golf cart, a boat,
a quad bike, a UTV, or another vehicle, you need to make sure that your
vehicle battery or battery pack terminal voltage is 12VDC. If the battery
terminal voltage is not 12V, you will need a DCDC converter with output 12V.
Connecting the ExtremeController to a non-12VDC power source will lead to a
malfunction or damage to the controller. Note: Besides the power supply, the
ExtremeController relies on the Remote Turn-On Signal Input to turn on and
off. Refer to Connecting the Remote Turn-On Input Wire to a Switch for more
details. Installation: 12V Power-In SAE Connector
1. Attach the 8ft Power Cable to the 12V Power-In SAE Connector. Use Caution:
Do NOT connect to 12V Battery if the Power In SAE Connector is wet. Contact
may cause electric shock and injury if wet.
2. Remove the 25 Amp Blade Fuse from the Fuse Holder. 7
Installation and Wiring
Use Caution: Do NOT remove Fuse if the Fuse Holder is wet. An improperly
fitted cap may cause electric shock and injury if wet.
3. To close properly, push firmly to be sure the cap snaps into place.
4. Next follow either the Gas Vehicle or Electric Vehicle Installation
instructions.
Installation: Gas Vehicle
1. Loosen the bolts on the battery terminals.
Use Caution: Do NOT attempt to loosen bolts if battery is wet. Contact may
cause electric shock and injury if wet.
2. Connect the BLACK wire to the BLACK, negative terminal, then the RED wire
to the RED, positive terminal. Unit will not work correctly and may be damaged
if wires are not correctly attached.
3. Tighten the bolts on the battery terminals until the connectors are held
firmly in place.
4. Return the 25 Amp Blade Fuse into the Fuse Holder and close the cap.
Tip: Use zip ties to gather any excess wires, and secure them so that they are
not dangling, loosely.
Loosen Bolts Black Cable Red Cable
Tighten Bolts
8
Installation and Wiring
Installation: Electric Vehicle
1. Switch your vehicle to Tow mode, if available.
2. Wire the BLACK wire to the GROUND on output of the DC-DC Converter.
3. Wire the RED wire to the POSITIVE (+) post on the output of the DC-DC
converter. Unit will not work correctly and may be damaged if wires are not
correctly attached.
4. Return the 25 Amp Blade Fuse into the Fuse Holder and close the cap.
Use Caution: Do NOT connect to DC-DC converter if the 8ft Power Cable or the
Power-In SAE Connector are wet. Contact may cause electric shock and injury if
wet.
Tip: Use zip ties to gather any excess wires, and secure them so that they are
not dangling, loosely.
Black Cable
Red Cable
Connecting the Remote Turn-On Input Wire to a Switch
Besides the 12V power supply, the ExtremeController relies on the Remote Turn-
On Signal Input to turn on and power off. The input voltage range to turn on
is 12V to 56V. When the input voltage is 0, it will power off the controller.
You will need to connect the (Dark Blue) Remote Turn-On Wire to the vehicle
ignition switch with the supplied (Dark Blue) Remote Turn-On Extension Cable.
If you are not able to connect it to your vehicle ignition switch, connect
this input to a rocker switch (not
9
Installation and Wiring
included), then connect the rocker switch to a 12V to 56V power supply on your
vehicle or to a switch accessory panel. WARNING: The RF Remote Control does
NOT turn off the ExtremeController. The Remote only turns off the connected
LEDs. To prevent draining your vehicle’s battery, you must turn the vehicle
ignition off or the rocker switch off. Connecting to a Switch
Power Accessories
Ground To connect the ExtremeController to your vehicle’s ignition switch or a
rocker switch, follow the steps below:
1. Connect the (Dark Blue) Remote Turn-On Wire to the Accessories terminal of
your switch with the supplied (Dark Blue) Remote Turn-On Extension Cable.
2. Connect the Power terminal of your switch to your vehicle’s (12V – 56V)
power supply terminal with a cable that comes with your switch.
10
Installation and Wiring
Vehicle Battery
+12V Power Accessories
12V Power-In SAE Connector + 8ft Power Cable
Switch
Remote Turn-On Wire + 10ft Extension Cable
3. Once the connections are completed, the ExtremeController will turn on or
off when the switch is turned on or off.
Connecting to a Power Panel or Switch Panel If your vehicle has an accessory
power panel or switch panel, you can use a connection on the panel to turn the
ExtremeController on or off with the following steps: 1. Find a terminal on
the panel that has 12VDC – 56VDC output when
the switch is on and 0VDC output when the switch is off.
11
Installation and Wiring
2. Connect the (Dark Blue) Remote Turn-On Wire to the switch terminal with the supplied (Dark Blue) Remote Turn-On Extension Cable.
+12V Power
GND
Switch Terminal Switch On: 12VDC Switch Off: 0VDC
Vehicle Power / Switch Panel
12
Installation and Wiring
3. Once the connection is completed, when the vehicle is on, the
ExtremeController will turn on or off when the panel is turned on or off.
Recommendation: If you are not familiar with all of the switch connections on
the panel, consult your switch accessory panel’s manual or a technician.
Incorrect connections to your panel may cause your controller or your panel to
malfunction.
Connecting LEDCast-Enabled Products
1. Once the 12V Power and Remote-Turn On Input connections have been made,
turn on the vehicle ignition switch (or the rocker switch). The Connection
Status LED Indicator will flash Blue, indicating a successful power
connection. If not, check the ExtremeController wirings.
2. Now, turn off the vehicle ignition switch (or the rocker switch) to turn
off the ExtremeController. To avoid potential damage to the product, you MUST
disconnect the SAE Power Cable from the controller before connecting a
SoundExtreme LED product to it.
3. Connect LEDCast-enabled products to any of the 4 LED Control Outputs. The
following is an example configuration by Zone:
· Zone 1: ExtremeStrip Roof.
· Zone 2: ExtremeStrip Underglow.
· Zone 3 (left): ExtremeWhip installed on the vehicle’s left side.
· Zone 4 (right): ExtremeWhip installed on the vehicle’s right side.
Run the LED control cable from the LEDCast-enabled product to the
ExtremeController, making sure the cable does NOT touch any moving parts on
the vehicle. If the cable is longer than required, do NOT cut the cable and
reconnect. Instead, wrap the extra length on your vehicle and fasten the cable
with zip ties. Please ensure the cable does NOT touch or drag on the ground
AND is safely secured to prevent it from coming into contact with any moving
parts.
13
Installation and Wiring
4. To connect the cables connect the 3-pin female connector on the control
cable to the 3-pin male connector on a LEDCast-enabled product. Align the
arrow on both connectors, push in and screw the nut cap on the female
connector. Connect the 3-pin male connector on the control cable to the LED
control output 3-pin female connector on the ExtremeController.
5. Optional: Integrate with the Vehicle Signal Inputs. If you are familiar
with all of your vehicle’s signal input connections, you can connect the
Vehicle Signal Input Control Connectors to your vehicle’s turn, brake, and
reverse wires (connection cables between the ExtremeController and your
vehicle signal are not included) to add the Street Mode function to Zone 3 and
4.
· Pink Wire: Reverse Signal · Orange Wire: Brake Signal · Green Wire: Left
Turn Signal · Blue Wire: Right Turn Signal
Recommendation: If you are not sure where these signal wires are located on
your vehicle, consult your vehicle’s manual or a technician. Incorrect
connections to your vehicle may cause your controller or your vehicle to
malfunction. 14
Installation and Wiring
IMPORTANT: After you complete all the wiring and turn on the ExtremeController
for the first time, test for proper wiring and function as follows: · Turn
vehicle’s left turn signal on: LED’s connected to Zone 3 will
flash Yellow. · Turn vehicle’s right turn signal on: LED’s connected to Zone 4
will
flash Yellow. · Press the vehicle’s brake: LED’s connected to Zone 3 and 4
will
shine Red. · Carefully put your vehicle in reverse: LED’s connected to Zone 3
and 4 will shine White. 6. Wiring is now complete. When power is provided to
the
ExtremeController, use the included RF Remote Control or SoundExtreme
Smartphone App to control the system.
15
Lighting Control Concepts
Zones
A Zone corresponds to all of the LED lights that are connected directly to one
physical LED Control Output on the ExtremeController. When you change a Zone
status (On/ Off, Mode, etc.), the LEDs connected to that Zone will change
accordingly. You can control one Zone or multiple Zones at a time.
Modes
There are 3 LED Mode categories, totaling in 44 Modes supported by the RF
Remote. The SoundExtreme app can support many more Color Modes.
1. Color Mode: Each Color Mode lights up the LEDs in a solid color. There are
8 Color Buttons on the Remote Control: Red, Green, Blue, White, Orange,
Yellow, Cyan, and Purple. You can create a custom color by utilizing the
SoundExtreme Smartphone App.
2. Party Mode: There are 20 preset Party Modes accessible via the Remote
Control and SoundExtreme Smartphone App. The app allows you to customize each
of the 20 Party Modes, allowing for nearly unlimited color, cascading, and LED
chasing options.
3. Music Mode: There are 16 Music Modes accessible via the Remote Control and
SoundExtreme Smartphone App. In order to sync with the music, the
ExtremeController must be wirelessly connected to an EcoCast-enabled ECOXGEAR
or SoundExtreme audio product. Refer to EcoCast for Music Mode for more
information.
Scene
A Scene is programed via the SoundExtreme Smartphone App. You can customize
each Zone into a Scene (a preset). Setting the Scenes on the app allows a
1-button press to bring up your desired custom settings for all of the LED
products connected to the ExtremeController. 16
Lighting Control Concepts
The ExtremeController supports 6 lighting Scenes. Scenes 1-5 are user
customizable and programmable. The 6th scene, Street Mode, is for special use
and cannot be modified. The default Scene settings are:
· Scene 1: Orange for all 4 Zones.
· Scene 2: Flowing colors for all 4 Zones.
· Scene 3: Patriot 1 for all 4 Zones.
· Scene 4: Fading colors for all 4 Zones.
· Scene 5: Christmas for all 4 Zones.
· Scene 6: Street Mode Turns all LED lights off but keeps the controller
powered on so Zones 3 and 4 will still function as enhanced brake, reverse,
and turn signal lights.
Street Mode: Zone 3 and 4 Vehicle Signaling
If you have Integrated the ExtremeController with the Vehicle’s Signal Inputs,
you can use the Street Mode function.
Under normal operations, when all 4 Zones are turned off, the vehicle
signaling in Zones 3 and 4 automatically enters Off Mode.
When LEDs in any of the 4 Zones are turned on, as soon as the controller has a
vehicle’s signal input, Zone 3 and 4 LEDs will light up accordingly. The LEDs
will resume their original status (an LED Mode) once the vehicle signal input
is gone.
You can also use the RF Remote Control to turn the LED lights in all 4 Zones
on or off (when the controller has a vehicle’s Remote TurnOn Signal Input).
Simply press the ALL Button to turn the LEDs in all 4 Zones on or off. When
the LEDs in all 4 Zones are turned off, the controller has the following two
functions:
· Off Mode: When the LEDs in all 4 Zones are turned off, the controller
disables the vehicle signaling to the LEDs in Zones 3 and 4, i.e. Zone 3 and 4
LEDs will not light up, even if there is a vehicle
17
Lighting Control Concepts
signal input. This Off Mode is for users who do not want their LEDs to light
up while they are driving.
· Street Mode: When the controller is in this Mode, all 4 Zone LEDs are also
turned off. However, as soon as the controller has a vehicle’s signal input,
the LEDs in Zone 3 and 4 will light up accordingly. The LEDs will turn off
once the vehicle signal input is gone.
To enable Street Mode, press the Scene Button on the Remote to cycle through
to the 6th Scene or use the SoundExtreme Smartphone App and select Scene 6
Street Mode.
When the ExtremeController enters Street Mode, each of the LEDs in all 4 Zones
will briefly light up Blue in ascending order to indicate that Street Mode is
active.
When the ExtremeController is in Street Mode, any Mode change to a Zone (e.g.
change Zone 1 Color) or Scene change will bring the controller out of Street
Mode and into the selected setting.
When the controller exits Street Mode, each of the LEDs in all 4 Zones will
briefly light up Blue in descending order.
EcoCast for Music Mode
The ExtremeController is compatible with the ECOXGEAR audio and LED lighting
EcoSystem, which includes LEDCast and EcoCast Innovations. Look for the
LEDCast and EcoCast logos on the growing family of ECOXGEAR and SoundExtreme
audio and lighting solutions. EcoCast-enabled audio products are designed to
be paired with one or more EcoCast-enabled products. Simply initiate EcoCast
Transmitting Mode in one SoundExtreme or ECOXGEAR speaker and broadcast your
music to one or more EcoCast-enabled products in Receiving Mode. Once
connected to your controller, select a Music Mode to have all of your LED
lights complement the music.
Note: The ExtremeController is always in EcoCast Receiving Mode.
18
Lighting Control Concepts
EcoCast: Speaker to ExtremeController B
A
1. Follow the Pairing a Bluetooth Device instructions in your speaker’s user
guide to connect it (Speaker A) to your Bluetooth device. After your device is
connected to Speaker A, you can select a song to play.
2. Initiate EcoCast Transmitting Mode on Speaker A. 3. Power on your
ExtremeController (Controller B). It will already
be in EcoCast Receiving Mode. The Connection Status LED Indicator will flash
Green. 4. Once the connection between the products is successful, the
Connection Status LED Indicator on Controller B will shine solid Green. You
can now select one of the 16 Music Modes with the Remote Control or the
SoundExtreme Smartphone App. EcoCast: Additional Receiving Speakers and / or
Controllers
B
C A
D
19
Lighting Control Concepts
1. Power on the additional EcoCast-enabled products (Speaker C and Controller
D) and initiate EcoCast Receiving Mode in Speaker C (Controller D will already
be in EcoCast Receiving Mode). The Connection Status LED Indicator on
Controller D will flash Green.
2. Reinitiate EcoCast pairing on Speaker A. 3. Once the connection between
the speakers is successful, the
Connection Status LED Indicator on Controller D will shine solid Green. You
can now select one of the 16 Music Modes. Notes: · If all the speakers are
turned off, then turned on, the speaker(s) and controller(s) in EcoCast
Receiving Mode (Speakers and Controllers B, C, and D) will automatically re-
connect to the speaker in Transmitting Mode (Speaker A). If they are not
automatically re-connected, please follow the above steps. · To clear pairing
records on an ExtremeController, PRESS AND HOLD for 3 seconds. · If the
ExtremeController is unable to pair and connect with the speaker, re-enable
the EcoCast pairing on the speaker, then PRESS AND HOLD the ALL Button on the
RF Remote Control to enable EcoCast pairing on the controller. · The EcoCast
functionality is only available while using Bluetooth as your Audio Source on
legacy ECOXGEAR products at a maximum range of 30 feet between speakers. ·
While connecting the EcoCast-enabled products, make sure that they are within
a few feet of each other.
20
Standby Button
RF Remote Control
Zone Buttons: Z1 · · · Z4
Common Buttons: Mode, Scene, Bright, Speed, and Color
Zone-Mode Buttons: Z1-M · · · Z4-M
The RF Remote Control comes paired to the ExtremeController.
If the ExtremeController does not react when you press a button on the Remote
Control, check if the battery isolator (clear plastic strip) on the Remote
battery compartment is removed (pulled out) completely. Then, power off and
power on the ExtremeController. When the Connection Status LED Indicator on
the controller flashes Blue, PRESS AND HOLD the Mode Button on the Remote for
3 seconds. The Status LED Indicator will shine solid Green for 1 second, then
flash Green, indicating a successful pair.
Basic Functions
1. Turn on the vehicle ignition switch (or the rocker switch) to power on the
ExtremeController.
2. Press the ALL Button to turn on the LEDs in all of the Zones. Each of the
LEDs will briefly light up Green in ascending order and then shine solid
Orange or a random color pattern.
3. If you don’t see the LEDs light up, as a test, short-press the Red Button.
The LEDs in all the Zones will shine solid Red.
21
RF Remote Control
4. There are three ways to change the LED Mode:
· Short-press the Mode Button to cycle through the three LED Mode categories
for all the Zones.
· Short-press one of the 8 Color Buttons to light the LEDs in all the Zones in
the corresponding color.
· Short-press one of the Zone-Mode Buttons (Z1-M, Z2-M, Z3-M, or Z4-M) to
cycle through the three LED Mode categories for only the corresponding Zone.
Note: There are 44 distinct LED Modes. Instead of using the Mode Button to
cycle through to a desired LED Mode, you can also use the SoundExtreme
Smartphone App to find a specific LED Mode.
5. To optimize the LED lighting performance the first time you use the
ExtremeController, or you change the LEDs physically connected to a Zone, use
the SoundExtreme Smartphone App to select the LED product connected to each
Zone. Refer to the SoundExtreme Smartphone App instructions for more details.
6. If you have an ECOXGEAR speaker with EcoCast capability and / or a
SoundExtreme speaker with LEDCast technology, you can connect the
ExtremeController to either product for Music Mode.
If the ExtremeController is unable to pair and connect with the speaker, re-
enable the EcoCast pairing on the speaker, then PRESS AND HOLD the ALL Button
on the RF Remote Control to enable EcoCast pairing on the controller. Refer to
the EcoCast for Music Mode instructions for more details.
7. Short-press the Mode Button to cycle through the multiple Music Modes.
· When no music is playing the LED will be dark. So, please play music while
changing Music Modes to review the various Music Mode effects.
22
RF Remote Control
· There are 44 distinct LED Modes. Instead of using the Mode Button to cycle
through to a desired Music Mode, you can also use the SoundExtreme Smartphone
App to find a specific Music Mode.
8. Short-press any of the 8 Color Buttons to change the colors in all LED
Zones.
Advanced Functions
You can also change the LED lighting effect in only 1 Zone at a time: 1. To
activate the Zone you want to change, PRESS AND HOLD
the Zone Button. For example, press and hold the Z1 Button for 3 seconds. The
LEDs in Zone 1 will flash Green twice, indicating that Zone 1 is selected. 2.
You can now PRESS AND HOLD any of the 8 Color Buttons, the Bright Button, or
the Speed Button for 2 seconds (instead of a short-press) to modify the LEDs
in the selected Zone. 3. To change another Zone, e.g. Zone 3, PRESS AND HOLD
the Z3 Button. The LEDs on Zone 3 will flash Green twice, indicating that Zone
3 is selected. Follow step 2 to modify the LEDs in Zone 3. Note: Anytime you
short-press a Common Button on the Remote, it will change the LEDs on all
Zones.
23
Remote Functions Overview
BUTTON
ACTION
Short-Press
FUNCTION
Turn on / off the LEDs in all Zones.
Press and Hold (for 3 seconds)
Short-Press
To enable EcoCast pairing. To turn on / off the Zone 1 LEDs.
Press and Hold (for 3 seconds)
Short-Press
To select Zone 1. To turn on / off the Zone 2 LEDs.
Press and Hold (for 3 seconds)
Short-Press
To select Zone 2. To turn on / off the Zone 3 LEDs.
Press and Hold (for 3 seconds)
Short-Press
To select Zone 3. To turn on / off the Zone 4 LEDs.
Press and Hold (for 3 seconds)
To select Zone 4.
24
Remote Functions Overview
NOTES
· When turned on, each of the LEDs will light up Green in ascending order.
When turned off, the LEDs light up Red in descending order.
· Does not turn off the ExtremeController. Only the vehicle ignition switch
(or rocker switch) can power off the controller.
· Refer to Zones, Modes, and Scenes. Note: If you want to turn all of the LED
lights off but still want Zones 3 and 4 to function as enhanced brake,
reverse, and turn signal lights, use Street Mode (Scene 6).
· The Button on the ExtremeController has the same Action / Function.
· When turned on, LEDs in Zone 1 will light up Green in ascending order. When
turned off, the LEDs light up Red in descending order.
· The LEDs in Zone 1 will flash Green twice, indicating that the (Bright,
Speed, and Color) Common Buttons will only apply to Zone 1.
· When turned on, LEDs in Zone 2 will light up Green in ascending order. When
turned off, the LEDs light up Red in descending order.
· The LEDs in Zone 2 will flash Green twice, indicating that the (Bright,
Speed, and Color) Common Buttons will only apply to Zone 2.
· When turned on, LEDs in Zone 3 will light up Green in ascending order. When
turned off, the LEDs light up Red in descending order.
· The LEDs in Zone 3 will flash Green twice, indicating that the (Bright,
Speed, and Color) Common Buttons will only apply to Zone 3.
· When turned on, LEDs in Zone 4 will light up Green in ascending order. When
turned off, the LEDs light up Red in descending order.
· The LEDs in Zone 4 will flash Green twice, indicating that the (Bright,
Speed, and Color) Common Buttons will only apply to Zone 4.
25
Remote Functions Overview
BUTTON
ACTION
Short-Press Double-Click Short-Press Double-Click Short-Press Double-Click
Short-Press Double-Click Short-Press
FUNCTION
To cycle through the three LED Mode categories for Zone 1.
To cycle back to the previous LED Mode for Zone 1.
To cycle through the three LED Mode categories for Zone 2.
To cycle back to the previous LED Mode for Zone 2.
To cycle through the three LED Mode categories for Zone 3.
To cycle back to the previous LED Mode for Zone 3.
To cycle through the three LED Mode categories for Zone 4.
To cycle back to the previous LED Mode for Zone 4.
To cycle through the three LED Mode categories for all the Zones.
Double-Click
Press and Hold (for 3 seconds)
To cycle back to the previous LED Mode for ALL Zones.
To enter Pairing Mode with the ExtremeController.
26
Remote Functions Overview
NOTES
· There are 44 distinct LED Modes: 8 Color Modes, 18 Party Modes, and 16 Music
Modes. You can also use the SoundExtreme Smartphone App to find a specific LED
Mode.
· The RF Remote Control comes paired to the ExtremeController. This feature is
meant to be used if the connection is lost or a replacement Remote is
purchased.
27
Remote Functions Overview
BUTTON
ACTION
Short-Press
Press and Hold (for 3 seconds)
Short-Press
Press and Hold (for 2 seconds)
Short-Press
Press and Hold (for 2 seconds)
Short-Press
FUNCTION
To cycle through the 5 defined Scenes for all the Zones.
To set all Zones to shine Orange, at 100% brightness and 80% speed.
To cycle through 5 levels of Brightness for all the Zones.
To cycle through 5 levels of Brightness for the selected Zone.
To cycle through 5 levels of Speed for all the Zones.
To cycle through 5 levels of Speed for the selected Zone.
To select the corresponding Color for all the Zones.
Press and Hold (for 2 seconds)
To select the corresponding Color for the selected Zone.
28
Remote Functions Overview
NOTES
· Scene 6 (Street Mode) turns all the LED lights off but Zones 3 and 4 will
still function as enhanced brake, reverse, and turn signal lights.
· This feature is only available when one of the Zones has been selected via
one of the Zone Buttons. (Press and hold Z1, Z2, Z3, or Z4 for 3 seconds).
· This feature is only available when one of the Zones has been selected via
one of the Zone Buttons. (Press and hold Z1, Z2, Z3, or Z4 for 3 seconds).
· There are 8 Color Buttons on the Remote Control: Red, Green, Blue, White,
Orange, Yellow, Cyan, and Purple. You can also use the SoundExtreme Smartphone
App create a custom color.
· This feature is only available when one of the Zones has been selected via
one of the Zone Buttons. (Press and hold Z1, Z2, Z3, or Z4 for 3 seconds).
29
SoundExtreme App
The ExtremeController can be operated via the SoundExtreme Smartphone App.
Download and Install
For iPhones, download the app from the following URL:
https://apps.apple.com/us/app/soundextreme/id1670708941 For Android phones,
download the app from the following URL:
https://play.google.com/store/apps/details?id=com.cchip.ecoxgear
Alternatively, use the following QR Codes to download the SoundExtreme
Smartphone App.
iOS
Android
App Overview
Password Secured: The app is password protected so others cannot gain access
and control your ExtremeController. The default password is 0000.
Name Your Devices: You can change and customize the name of your devices and
Zones, such as Rear speakers, Soundbar, Subwoofer, Cabin Lights, Underglows,
Roof Lights, Whips, etc.
Set Up Modes: Use the app to set up the LED Mode for each of the 4 Zones on
your ExtremeController. You can also change the Brightness and Speed.
30
SoundExtreme App
Create and save Scenes: A Scene is a preprogrammed light show that you can
save for later quick-access. We have created 5 default Scenes that are fully
customizable and programmable. Set Up a Group: Create and set up a group of
devices (multiple ExtremeControllers, or other SoundExtreme products with
LEDCast built-in). This will allow all the LED lights connected to different
devices to be controlled by the SoundExtreme Smartphone App at the same time.
Bluetooth Low Energy: The SoundExtreme Smartphone App relies on a BLE
(Bluetooth Low Energy) connection between your phone and the
ExtremeController. Make sure you turn on Bluetooth on your smartphone.
Initial App Connection and Device & LED Setup
1. Launch the SoundExtreme App on your smartphone or other BLE-enabled
device.
2. On the SoundExtreme App homepage, tap Refresh List.
31
SoundExtreme App
3. If your ExtremeController is powered on, it will show up as 4 Zone
Controller on the app’s Connect Device screen. Tap the device name on the
screen. A checkmark will appear on the right. Tap the Connect button.
4. A dialog window will popup asking you to enter a password. The
ExtremeController default password is 0000.
5. If the app connects to your ExtremeController successfully, a popup
message will appear, showing the Device & LED Settings for the 4 Zones on your
controller and ask you if you want to change the settings. On the bottom of
the message there is a checkbox to ask if you want this message to be
displayed the next time the app connects to your controller.
6. If you choose to change the Device & LED Settings, the app will bring you
to the Device & LED Set Up menu for you to choose the LED device from the
pull-down list.
32
7. Once the Device & LED Settings are completed, the app will bring you to
the Device screen.
8. Select your controller. It will take you to the Scene Screen. There are 6
predefined Scenes on the controller. You can turn on one of first 5 Scenes to
light up the LEDs. For example, click the On / Off button at the right for
Scene 1, the Speaker LEDs will light up Orange, which is the LED lighting mode
defined for Scene 1.
SoundExtreme App
33
SoundExtreme App
Set Up Zones
1. Select your ExtremeController on the Device list, and the app will bring
you to the Zone screen.
2. Tap one of the 4 Zones, and you will go to the Zone LED Mode Settings
screen. There are 3 tabs: Color, Party, and Music, which allow you to select a
solid Color, a Party Mode, or a Music Mode.
34
· When you choose a Mode, the LEDs connected to the Zone you selected will
light up accordingly, giving you a preview.
· If you tap the Save button on the screen, the app will save your setting for
the selected Zone.
· If you tap the Cancel button or exit the LED Mode Settings screen, your Mode
selection will not be saved and LEDs connected to that Zone will display the
previously selected LED Mode.
SoundExtreme App
35
SoundExtreme App
3. After you set up the Modes for each of the Zones, the controller setup is
complete.
36
Set Up Scenes
1. Select your ExtremeController on the Device list, and the app will bring
you to the Zone screen. Tap the Scene tab. The app will show 6 pre-defined
scenes on your controller. As previously mentioned in Zones, Modes, and
Scenes, Scene 6 is designed for Street Mode and not editable. Street Mode
turns all the lights off but keeps the controller on. If you have the
controller connected to your vehicle’s turn signals, brakes and / or reverse
wires, the connected LED devices in Zones 3 and 4 will still light up when
applicable.
2. You can change a Scene’s LED settings by selecting any of the first 5
Scenes. When you select the Scene you will go to the LED Mode Setting screen.
You can use the same procedure as in the Set Up Zones section to set up each
Zone and save the Scene’s new LED settings.
SoundExtreme App
37
SoundExtreme App
3. After you set up LED Modes for all the Zones, the setup is complete for
the selected Scene.
Change Password
To add extra security, you can change the default password of 0000 to your
desired 4-digit numeric password. Please note that the password is stored in
your ExtremeController, not the SoundExtreme app. So, after you change the
password, please make a note in case you forget your password. The password
won’t be reset by reinstalling the app or changing to another smartphone. The
only way to reset your password is to conduct a factory reset on your
ExtremeController.
1. Select the Menu Icon at the top-right corner of the screen.
2. Select Device Password from the menu.
3. Once at the Device Password screen, select the device that you want to
change the password to.
38
4. Enter the current password, the new password, and re-enter the new
password. Then tap the Confirm button.
5. If the change is successfully saved, the app will display a confirmation
message.
This is a one-time event. You do not have to enter in your password every time
you launch the app, as your app will remember your password.
SoundExtreme App
39
SoundExtreme App
Factory Reset
If you forget the password, you will need to do a Factory Reset on the
ExtremeController so that the password is reset to its default value: 0000. ·
Turn off the power to the ExtremeController by turning off the
ignition switch (or the rocker switch), then turn it back on. · While the
Status LED Indicator flashes Blue, PRESS AND HOLD
the Button for 3 seconds. The indicator will flash Yellow to show that the
reset is successful. Note: Besides the password reset, a Factory Reset will
also configure the ExtremeController to the following factory settings: · The
LED Device Type is set to 6′ ExtremeWhip for all 4 Zones. · The LED Mode is
set to solid Orange Color with 100% Brightness and the Speed is set to 80%,
for all the 4 Zones. · All 5 customer configurable Scenes are set to the
Factory Default Scenes.
40
Dimensions
Specifications
4.6 in / 116.9 mm
3.13 in / 79.4 mm
1.04 in / 26.4 mm
Unit Weight 0.44 lbs (0.2 kg)
Power Input 12V, 20A
Remote Turn-on Input 12V 56V
Vehicle Signal (Left, Right, Brake, Reverse) Input: 12V
Blade Fuse 25A, 32V
EcoCast Range 30 ft / 9.1 m between Casting speaker and ExtremeController
LED Control Output on Each Zone 5A
Storage Temperature -40°F to 122°F / -40°C to 50°C
Operating Temperature 23°F to 95°F / -5°C to 35°C
Bluetooth Frequency Band 2.402~2.480GHz ISM Spectrum
Bluetooth Compliance Bluetooth® 5.1
41
Important Legal Information
FCC STATEMENT:
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: 1.) This device may not cause harmful
interference, and 2.) This device must accept any interference received,
including interference that may cause undesired operation. WARNING: Changes or
modifications not expressly approved by the party responsible for compliance
could void the user’s authority to operate the equipment. NOTE: FCC’s RF
Exposure guidelines, this equipment should be installed and operated with
minimum distance between 20cm the radiator to your body. This equipment has
been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential
installation. This equipment generates, uses, and can radiate radio frequency
energy and, if not installed and used in accordance with the instructions, may
cause harmful interference to radio communications. However, there is no
guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures: reorient or relocate the receiving antenna, increase the
separation between the equipment and receiver, connect the equipment into an
outlet on a circuit different from that to which the receiver is connected,
consult the dealer or an experienced radio/TV technician for help.
RF WARNING STATEMENT:
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
IC STATEMENT:
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions: 1.) This device may not
cause interference, and 2.) This device must accept any interference,
including interference that may cause undesired operation of the device.
PRODUCT USE AND PROTECTION:
Read and follow all instructions. Use only as intended. The SoundExtreme unit
is intended to be used indoors or outdoors and in land or water environments.
The unit has been tested to IP66 waterproofing standards, which means the unit
can be exposed to dust and water, but should NOT be submerged underwater. To
prevent fire or shock, do NOT attempt to power this unit if it is wet or you
suspect water has entered the unit. In this situation, please return the unit
to SoundExtreme for a free assessment. If we have found that the unit has
carried water, we will repair or replace the unit free of charge.
SAFETY ADVISORY & WARNING:
Read and follow all instructions. Use only as intended. CAUTION: Do NOT open
to repair. A qualified technician must carry out repair work. ATTENTION: Do
NOT connect to a SoundExtreme product with LEDCast technology while the unit
is wet. Make sure
all connections are dry BEFORE connecting to a power source. Failure to do so
may result in electrical damage to the unit and may void the warranty.
WARNING: Cancer and Reproductive Harm – www.P65Warnings.ca.gov ATTENTION: Do
NOT dispose of in a landfill. Contact SoundExtreme at www.gracesupport.com or
a certified recycling agent to dispose of the unit.
SAFETY:
This product has a limited life span of use and should be replaced when it
shows obvious signs of wear. Do not modify or remove any original component
parts of the speaker. Doing so could cause damage to the unit, allowing water
to ingress. A unit with water ingress should not be charged due to potential
risk of fire or shock. Please exercise care and good judgment when using your
SoundExtreme unit. You should always 1.) Return the unit to SoundExtreme if
you suspect water ingress into the unit or if the unit has experienced a
severe
impact that may have affected the integrity of the unit to take on water.
42
Important Legal Information
You should never 1.) Never power your SoundExtreme unit if you suspect water
has entered the device. Powering a device with water
inside could be potentially hazardous and cause fire or a spark. 2.) Never use
your SoundExtreme unit if you have dropped it or thrown it against a hard
surface which may have
destroyed the integrity of the housing. In the event of a severe impact to
your unit, please return the unit to SoundExtreme to review for potential
damage. 3.) Never attempt to fix, repair your SoundExtreme unit . Please send
it back to SoundExtreme for any assessments and repairs.
CARE, MAINTENANCE & PRECAUTIONS:
1.) Do NOT apply excessive force to any surfaces of the unit. 2.) Do NOT use
or store the unit in places with high temperature. 3.) AVOID prolonged
exposure to ultraviolet radiation (UV sunlight) and strong magnetic fields.
LIMITED MANUFACTURER’S WARRANTY:
The ExtremeController is covered by a 1-year limited warranty that covers
defects in workmanship and / or materials for a period of 1 year from original
purchase date. This warranty does not apply to any products which have been
abused, neglected, modified or used for a purpose other than the one for which
they were manufactured. Please refer to the above care and maintenance
instructions for suggested care details. The warranty is valid only for the
original owner who purchases the unit from an authorized dealer. Transfers do
not qualify for warranty protection. SoundExtreme reserves the right to
replace any out-of-stock or discontinued product with a comparable product.
Discontinued products may not be available for warranty replacement. Any
contents are NOT covered by the limited manufacturer’s warranty. Warranty
terms may be revised without notification at the discretion of the
manufacturer. Please visit www.soundextreme.us for additional product &
warranty information.
ExtremeController by SoundExtreme Inc., Houston, Texas. Designed in Texas.
Made in China.
43
What’s in the Box
ExtremeController
RF Remote Control
SAE Power Cable 8 ft long Remote Turn-On Extension Cable (Dark Blue) 10 ft long
44
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>