Clarke UBL1600R Rechargeable Under Car Bonnet LED Light User Manual

UNDERBONNET WORKLIGHT
MODEL NO: UBL1600R
PART NO: 4003536USER INSTRUCTIONS
ORIGINAL INSTRUCTIONS
GC07/23

INTRODUCTION

Thank you for purchasing this CLARKE worklight.
This underbonnet lamp incorporates a telescopic beam and two rubber coated brackets to assist in positioning in the underbonnet area. The LED lamp gives complete engine bay illumination without the inconvenience of a mains cable. The magnet at each end provides an alternative method of mounting the unit against a car body.
Before attempting to use this worklight, please read this manual thoroughly and follow the instructions carefully.

GUARANTEE

This worklight is guaranteed against faulty manufacture for a period of 12 months from the date of purchase. Please keep your receipt which will be required as proof of purchase.
This guarantee is invalid if the worklight is found to have been abused or tampered with in any way, or not used for its intended purpose.
Faulty goods should be returned to their place of purchase, no worklight can be returned to us without prior permission.
This guarantee does not effect your statutory rights.

ENVIRONMENTAL RECYCLING POLICY

**** Through purchase of this worklight, the customer is taking on the obligation to deal with the WEEE in accordance with the WEEE regulations in relation to the treatment, recycling & recovery and environmentally sound disposal of the WEEE.
In effect, this means that this worklight must not be disposed of with general household waste. It must be disposed of according to the laws governing Waste Electrical and Electronic Equipment (WEEE) at a recognised disposal facility.
The light source contained in this worklight has a life expectancy of approximately 50000 hours after which the worklight should be disposed of in an environmentally responsible way.
The Lithium Ion battery falls under the Waste Batteries and Accumulators Regulations 2009 and should be disposed of in a controlled manner.

SAFETY INSTRUCTIONS

1. ALWAYS check for damage before using the worklight. Inspect the power cable and plug for damage. Any damage should be properly repaired or the part replaced. Consult your local CLARKE dealer.
2. ALWAYS ensure that the voltage marked on the charger matches the power supply to be used.
3. NEVER use this lamp in a bathroom or in the vicinity of a swimming pool.
4. NEVER cover the lamp.
5. NEVER pull the cable to remove the charger plug from the power supply.
6. DO NOT look directly into the worklight when it is switched on.
7. Keep the worklight out of the reach of children.
8. Charge the worklight in a dry indoor location. DO NOT immerse in water or any other liquid.
9. ALWAYS fully charge before first use.
10. DO NOT turn on the light when charging.
11. DO NOT leave the worklight on charge for more than 24 hours.
12. DO NOT disassemble the worklight as there are no user changeable parts.
13. 13. This worklight utilises a rechargeable Lithium-ion battery that can rupture,
    ignite and cause serious injury if being used improperly.
    14. DO NOT put batteries and the worklight in the fire or high temperature.
    15. DO NOT puncture or damage the batteries.
    16. DO NOT immerse or expose the worklight to water.
    17. DO NOT dispose of the worklight in a fire or water.

THE FOLLOWING WARNING SYMBOLS ARE FOUND ON THE PRODUCT

| Indoor use
---|---
| Harmful to aquatic life
| Pacemaker hazard (due to magnet)
| Not suitable for use by children

CONTENTS

1. Lamp Body
2. Bracket x 2
3. Charger
4. M5x8 inner hexagon screws x 2
5. 4mm hexagon wrench

ASSEMBLY & CHARGING THE WORKLIGHT

1. Before use, fit the brackets to each end of the worklamp using the two screws supplied (a hex key is provided).
2. Connect the charger cable to the worklight and plug in to any domestic power socket.
3. The charger LED will change from green to red once the worklight is charging.
4. During this time, the battery condition display on the worklamp will display the condition as each of the blue LEDs will illuminate in turn as the charge status increases.
   • When all LEDs are continuously laminated the battery pack is fully charged. The charger LED will then change back to green.
   • Charge the battery every 3 months if the worklight is not in regular use to ensure the longevity of the battery unit.

OPERATION

SWITCHING ON AND OFF

1. Press the power button to ensure there is enough power before use. If low battery power or no power, continue to charge the worklight.
2. Press the power button to turn on.
   • Press and hold the power button and the brightness will drop to 20%. Press and hold again and the brightness can be cycled between 100%, 20% and Off.
   • The light flashes to show the setting has changed.
   • During use, the battery condition display will remain illuminated.

MOUNTING TO A CAR BONNET
To mount to an open car bonnet, extend the telescopic section until the brackets can be used to clamp the worklamp across the bonnet.

Note that the mounting hooks will not grip if the bonnet is raised over 45º.
Take extra care that the brackets do not slide down if the bonnet is wet.
Extend the lamp against the tension of the internal spring to suit the location.
The minimum size bonnet width is 1.15m meaning that the worklamp will not fit across small cars such as the Citroen C1, Toyota Yaris etc but can be used if fitted diagonally.

SPECIFICATION AND COMPONENT PARTS

DECLARATIONS OF CONFORMITY

| A SELECTION FROM THE VAST RANGE OF QUALITY PRODUCTS
AIR COMPRESSORS
From DIY to industrial, Plus air tools, spray guns and accessories.
GENERATORS
Prime duty or emergency standby for business, home and leisure.
POWER WASHERS
Hot and cold, electric and engine driven – we have what you need
WELDERS
Mig, Arc, Tig and Spot.
From DIY to auto/industrial.
METALWORKING
Drills, grinders and saws for DIY and professional use.
WOODWORKING
Saws, sanders, lathes, mortisers and dust extraction.
HYDRAULICS
Cranes, body repair kits, transmission jacks for all types of workshop use.
WATER PUMPS
Submersible, electric and engine driven for DIY, agriculture and industry.
POWER TOOLS
Angle grinders, cordless drill sets, saws and sanders.
STARTERS/CHARGERS
All sizes for car and commercial use.|
---|---|---

PARTS & SERVICE: 0208 988 7400
Parts Enquiries
Parts@clarkeinternational.com
Servicing & Technical Enquiries
Service@clarkeinternational.com
STE GUL RK Rg a aa
INTERNATIONAL
Hemnall Street, Epping, Essex CM16 4LG
www.clarkeinternational.com

Documents / Resources

| Clarke UBL1600R Rechargeable Under Car Bonnet LED Light [pdf] User Manual
UBL1600R Rechargeable Under Car Bonnet LED Light, UBL1600R, Rechargeable Under Car Bonnet LED Light, Under Car Bonnet LED Light, Car Bonnet LED Light, Bonnet LED Light, LED Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>