InVue S850 Handheld and Tablet Sensors Instruction Manual
- June 17, 2024
- inVue
Table of Contents
InVue S850 Handheld and Tablet Sensors
Product Information
Specifications:
- Model: S850/S960 Handheld and Tablet Sensors
- Connectivity: Micro USB, USB-C, Apple Lightning
- Compatibility: Standard and Insight Capable devices
Product Usage Instructions
Preparation:
Wipe the back of the device with the provided alcohol pad. Let it dry
completely.
Installation:
- If installing sensors on different types of devices, ensure to select the correct sensor type based on your device (handheld or tablet).
- Remove the clear film from the adhesive before proceeding.
Handheld Sensor:
Place the sensor on the centre of the back of the handheld device with the
sensor cable pointing towards the top of the device. Apply pressure for 10
seconds.
Tablet Sensor:
For tablet sensors, place the sensor on the centre of the back of the tablet
with the sensor cable facing the top of the device. Apply pressure for 10
seconds.
Wall-Mounted Handheld Devices:
- If using tablet sensors for wall-mounted handheld devices:
- Place the sensor on the back of the handheld with the sensor cable facing towards the bottom of the device. Apply pressure for 10 seconds.
- Stretch the alarm/power cable around the side of the sensor and plug it into the device.
Final Steps:
- Plug the sensor cable into the back of the stand.
- Place the device and sensor on top of the stand and plug in the alarm/power connector.
- The system is armed when the standing LED is illuminated.
Removal:
- To remove the sensor connector, use the key fob tool to press the black connector tab towards the connector. Failure to do so may result in a broken connector.
- Pull the sensor connector from the stand.
- To remove the sensor from the device:
- Unplug the alarm/power connector from the device.
- Use the scraper removal attachment (DNTX93) to break the adhesive bond between the sensor and the device.
Frequently Asked Questions (FAQ)
-
Q: Can I reuse the adhesive after removing a sensor?
A: No, it is recommended to use a new adhesive when reapplying a sensor to a device for optimal performance. -
Q: What should I do if the LED on the stand does not illuminate after arming?
A: Check the connections and ensure everything is properly plugged in. If issues persist, contact customer support for further assistance.
Handheld and Tablet Sensors, Micro USB, USB-C, Apple Lightning, Standard and Insight Capable.
Using Instruction
-
Wipe the back of device with the provided alcohol pad. Let it dry completely.
Note: Some devices may require the usage of a polish kit (ADH2300 or ADH2313) to promote the adhesion of an LSE plate or adhesive. -
If installing sensors on different types of devices, be sure to select the sensor type intended for your device. Handheld devices will use the sensor with the straight power connector cable and tablets will use the sensor with the coiled cable.
-
Remove the clear film from the adhesive.
-
4a. For Handheld Sensors:
Place the sensor in the centre of the back of the device with the sensor cable pointing towards the top of the device. Ap-ply pressure for 10 seconds.-
4b. For Tablet Sensors:
Place the sensor on the centre of the back of the tablet with the sensor cable facing the top of the device. Apply pressure for 10 seconds. -
4c. For wall-mounted Handheld devices use tablet sensors:
- Place the sensor on the back of the handheld with the sensor cable facing towards the bottom of the phone. Apply pressure for 10 seconds.
- Stretch the alarm/power cable around the side of the sensor as shown and plug it into the device.
-
-
Plug the sensor cable into the back of the stand.
-
Place the device & sensor on top of the stand and plug in the alarm/power connector.
-
The system is armed if the standing LED is illuminated.
-
To remove the sensor connector use the key fob tool to press the black connector tab in towards the connector.
Note: Failure to use the key fob to remove the connector may result in a broken connector. -
Pull the sensor connector from the stand.
-
To remove the sensor from the device:
-
Unplug the alarm/power connector from the device.
-
Use the scraper removal attachment (DNTX93) to break the adhesive bond between the sensor and the device.
Contact Information
- www.invue.com
- NA / LATAM // 704.752.6513 • 888.55.INVUE
- EMEA // +31.23.8900150
- APAC // +852.3127.6811
© 2023 InVue Security Products Inc. All rights reserved. InVue is a registered trademark of InVue Security Products.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>