KIDOMO F02 Mini Drone with Camera User Manual

USER MANUAL
KIDOMO F02 Mini Foldable Drone
V1.3

DISCLAIMER & SAFETY GUIDELINES

1. Please keep the small parts of the drone out of reach of children to avoid accidents.

2. Note that a distance of 2–3 meters should be maintained between the drone and the user or other people during flight to avoid injury caused by collision.

3. Do not dispose of this product as normal household waste.

4. Do not fly the drone above or near obstacles, crowds, open water, public roads, high-voltage power lines or trees.

5. Do not use the drone in severe weather conditions such as wind, snow, rain, smog, hail, lightning, tornadoes or hurricanes.

6. Keep clear of the rotating propellers and motors.

7. Keep the drone in eyesight at all times. Please do not rely solely on a first-person -view camera to control your drone.

8. Children operating the drone should be guided by an adult, and the drone should be kept within eyesight of the operator (or instructor) for easy control.

9. Be sure to observe all local regulations, obtain appropriate authorizations and understand the risks.
   NOTE: It is solely your responsibility to comply with all flight regulations.

10. Do not look directly at the beam to avoid injury caused by laser radiation. KIDOMO accepts no liability for damage, injury or legal responsibility incurred directly or indirectly from the use of this product. The user shall observe safe and lawful practices including but not limited to those set forth in these Safety Guidelines.

MAINTENANCE AND CARE

1. Thoroughly check the drone after a crash or violent impact.
2. Do not charge the battery before it cools down.
3. Remove the batteries if you will not use the drone for a long time.
4. Do not overcharge the battery. Unplug the charger once it is fully charged.
5. Store the drone and remote control in a cool dry place out of direct sunlight.
6. Avoid bringing the camera into direct contact with water or other liquids. Wipe it dry with a soft absorbent cloth if it gets wet.
7. Do not charge the battery next to flammables such as carpets and timber floors, or on the surfaces of electro-conductive objects. Always keep an eye on the battery while charging.
8. To avoid losing your drone, fly it in the open air after you have gained plenty experience and confidence in handling it.

DRONE DIAGRAM

REPLACING THE PROPELLERS

1. Replacement propellers must be replaced in their relative position on the machine. Propeller A must be installed in the A position and Propeller B must be installed in the B position, otherwise the control of the drone will be compromised.
2. During flight, Propeller A will rotate clockwise and Propeller B will rotate counterclockwise.

INSTALLING THE PROTECTIVE COVER
Snap the protective frame connectors into the shackles.

REMOTE CONTROL DIAGRAM

1. Power ON/OFF
2. Left Joystick
3. Right Joystick
4. Headless Mode
5. One-key Return
6. One-key Landing
7. One-key Takeoff
8. Fast/Slow Switch
9. Right Trimming
10. Left Trimming
11. Backward Trimming
12. Forward Trimming
13. Roll
14. Phone Clamps

INSTALLING BATTERIES

3×1.5V AAA batteries for the remote control (not included)Insert the battery into the drone (3.7V 650mAh Li-Po battery included)

RECHARGING DRONE BATTERY

First, take the battery out of the drone and connect one end of the USB charging cable to the USB interface of the computer (or USB power adapter) and the other end to the battery charging jack. The USB light will be on when charging and off when fully charged, and the charging time will be about 40 minutes. NOTE: Only use the provided charging cable. Do not use the provided charging cable to charge other products.

READY TO FLY

Note:

1. Make sure the propellers and protective covers are installed correctly and tightened, and that the power capacity of the drone is more than 50%.
2. Before flying, please set the frequency and calibrate the drone and remote control.

1. HOW TO SET THE FREQUENCY
Step1: Turn on the power of the fuselage and place the drone on a level surface.
Step2: Turn on the power switch of the remote control.
Step3: The two LED lights at the front of the drone will flash. Push the left joystick of the remote control to its highest point, then pull it to its lowest point. The controller will “beep”, indicating that frequency setting is complete. After completion, the LED light at the front of the drone will be steadily lit. 2. HOW TO CALIBRATE
Move the right joystick of the controller to the lower right side and the left joystick to the lower left (these actions should be performed at the same time). The two LED lights at the front of the drone will stop flashing and be steadily lit. When the controller emits a “beep”, the drone lights will be steadily lit, indicating successful calibration.
NOTE: If the drone encounters an impact or external collision, it can lead to a deviation in direction. In this case, land the drone on flat ground to ensure that its forward direction (the front of the lens) is consistent with the forward direction of the controller. Then complete the calibration. 3. LOW POWER ALARM
When the power capacity of the drone is lower than 50%, the two LED lights at the front of the drone will flash slowly. When the power of the drone is very low, the two LED lights will flash. In this case, stop flying the drone and only continue when it is fully charged.

FLIGHT OPERATION METHODS

Ascend/
descend| When the left joystick is pushed up/down, the drone will ascend/descend.|
---|---|---
Turn| When the left joystick is pushed left/right, the drone will turn left/right.|
Forward/
back| When the right joystick is pushed up/down, the drone will move forward/back.|
Sideways| When the right joystick is pushed left/right, the drone will move left/right.|
Roll| When the roll start button is pressed and the right joystick is pushed left/right, the drone will roll 360 degrees to the left/right.|

CONNECTING YOUR MOBILE DEVICE

1. Download the “WiFi_CAM” app on your mobile device from the App Store/Google Play or by scanning the QR code below.
2. Power on the drone and the LED lights will flash. Go to Wifi settings on your mobile device and connect to the network (KIDOMO___xxxxxx).

APP OPERATION PANEL

1. RUN THE APP “WiFi_CAM”
2. Press to enter help and information.
3. Press to enter the control interface.
4. CONTROL INTERFACE
5. Press to enter the flight control interface.
6. Press to open the hidden menu for more options.
7. Press to activate the altitude hold mode.

FLIGHT OPERATION GUIDE

1. HEADLESS MODE
The default front in the headless mode faces the direction in which the drone is facing when pairing with the remote control. If you need to change the direction the drone is facing in the headless mode, please re-pair it with the remote control.
In the headless mode, the drone always moves in the direction of the remote control joysticks, regardless of its orientation. For example, when you push the right joystick to the right, the drone will always move to the right (regardless of which direction the drone is facing).
Start: To enter this mode, turn on the drone, and press the Headless Mode button on the remote control. The remote control will keep beeping, the two LED lights at the front of the drone will flash and headless mode will start.
Exit: Press the “Headless Mode” button again to exit headless mode. The remote control will beep once and the indicator light will be steadily lit. 2. ONE-KEY RETURN
Press the “One-key Return” button and the drone will return automatically. If it deviates from its course when returning, the course can be corrected using the right joystick.
Note: When the drone is returning, press the “One-key Return” button again (the remote control will “beep”) and the drone will cancel the automatic return. Alternatively, push the right joystick forward and the drone will cancel the automatic return.
3. 360° FLIP
Fly the drone to a height of over 3 meters, press the “Roll” button and move the right joystick to make the drone perform a 360° flip. 4. TRAJECTORY FLIGHT
Tap to activate trajectory flight mode. Draw a path on the right margin of the screen and the drone will follow it. Tap the “Trajectory Flight” button again to exit this mode. 5. SPEED SWITCH
The drone is set to low speed by default. Press the “Speed Switch” button once for medium speed. Press it again for high speed. A third press will return it to low speed.
6. GESTURES FOR PHOTO/VIDEO
Tap to activate this function. When you face the camera and make a “High five” gesture within a distance of 2-3 meters of the camera, it takes a photo. When you face the camera and make a “fist” gesture within a distance of 2-3 meters of the camera, it records a video.

FAQ

Q1: Why do the drone LEDs not light up?

• Press the power switch on the drone. • Replace or recharge the drone battery. • Make sure the connectors of the battery are plugged in firmly.

Q2: Why do the drone LEDs keep flashing, but the drone never responds to any command from the remote control?

• Pair the drone with the remote control again. • Replace or recharge the drone battery. • Make sure the remote control batteries have enough power.

Q3: Why is flight not stable?

• Return the drone and restart to perform flight calibration as instructed. • Ensure flight trimming accordingly. • Fly the drone in suitable weather conditions.

Q4: Why is the drone unresponsive to the controls?

• Make sure the distance between the drone and the mobile device is effective. • Keep the drone away from open water, high-voltage power lines and trees.

CONTACT US

For any inquiries about KIDOMO products, please feel free to contact us.
We will respond within 24 hours.
Email: support@kidomo.net
Tel: 301-670-7335 (US) Mon-Fri 9am-5pm (EST)
Official website: www.kidomo.net

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>