Aqara WL-S02D Smart Home Water Leak Sensor T1 User Manual

: June 17, 2024
: Aqara

Table of Contents

Aqara WL-S02D Smart Home Water Leak Sensor T1
Product Information
Product Usage Instructions
Product Introduction
Device Binding & Initialization
Product Specifications
Safety Warnings And Caution
Declaration Of Conformity
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Aqara WL-S02D Smart Home Water Leak Sensor T1

Product Information

Aqara Water Leak Sensor T1 is a device that detects water leakage and soaking using the Zigbee 3.0 wireless communication protocol. It can detect transitions from waterless to water and from water to water-break. When leakage or soaking is detected, it sends timely alarm notifications through the app and can control other smart devices through hub linkage.

Indicator Light
The indicator light on the sensor serves different functions:

Long Press of 5s: Reset/Connect to Network
Single Press: Effective Range Test

Device Components

Reset Button
Inductive Probe

Product Usage Instructions

Device Binding & Initialization

Ensure the Aqara Home app and Aqara hub are installed.
Open the app, tap Home, then tap + in the top right corner to enter the Add Device (Accessory) page.
Select Water Leak Sensor T1 and follow the instructions to add it.
For detailed instructions, visit www.aqara.com/support or scan the QR code for the electronic manual.
If the connection fails, move the sensor closer to the Hub and try again.

Specifications

Model: WL-S02D
Battery: CR2032
Manufacturer: Lumi United Technology Co., Ltd.
Address: Room 801-804, Building 1, Chongwen Park, Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan Residential District, Nanshan District, Shenzhen, China

Warnings

This product is NOT a toy. Keep children away from it.
Designed for indoor use only. Do NOT use outdoors.
Do NOT place near a heat source. Ensure normal ventilation if placed in an enclosure.
Do NOT attempt self-repairs. Authorized professionals should handle repairs.
The product is for home entertainment and convenience purposes only; not for security use.

Caution

Risk of explosion if incorrect battery type is used. Dispose of used batteries properly.
Do not ingest the battery; it poses a Chemical Burn Hazard.
Keep batteries away from children to prevent swallowing.
Maintain a separation distance of at least 20cm between the antenna and the user’s body during normal use.

FAQ

Q: What should I do if the sensor does not detect water leakage?
A: Ensure the sensor is properly placed in areas prone to leaks and verify its connection to the hub.
Q: Can I use the sensor outdoors?
A: No, the sensor is designed for indoor use only to prevent damage.

Product Introduction

Aqara Water Leak Sensor T1 is a device that may detect water leakage and soaking based on the Zigbee 3.0 wireless communication protocol. It may detect two states, namely from waterless to water, from water to water-break. When leakage or soaking occurs, it may timely push the alarm information through the app, and control other smart hardware products through the linkage of the hub device.

An Aqara hub is required. Some functions require specific models of the Aqara hub. Please visit www.aqara.com/support for more details.

Long Press of 5s: Reset/Connect to Network
Single Press: Effective Range Test

Device Binding & Initialization

Before activating the accessory, please make sure you have the Aqara Home downloaded and the Aqara hub installed. Please open the app, “tap Home” and then tap”+” in the top right corner to enter the “Add Device (Accessory)” page.
Select”Water Leak Sensor T1″, and add it according to instructions.
For details, please see www.aqara.com/support or scan the QR code below to get the detailed electronic manual.

If the connection fails, please move the accessory closer to the Hub and try again

Product Specifications

Water Leak Sensor T1

Model: WL-S02D
Battery: CR2032
Wireless Protocols: Zigbee 3.0
Dimensions: ⌀50 × 50 × 15 mm (1.97 × 1.97 × 0.59 in.)
Zigbee Operation Frequency: 2405-2480 MHz
Zigbee Maximum Output Power ≤ 13 dBm
Operating Temperature: -10°C ~ 55°C (14°F ~ 131°F)
Operating Humidity: 0 ~ 100% RH, no condensation
What is in the Box: Water Leak Sensor T1 × 1, User Manual × 1
Manufacturer: Lumi United Technology Co., Ltd.
Address: Room 801-804, Building 1, Chongwen Park, Nanshan iPark, No. 3370, Liuxian Avenue, Fuguang Community, Taoyuan Residential District, Nanshan District, Shenzhen, China
Online Customer Service: www.aqara.com/support
Email: support@aqara.com.

Safety Warnings And Caution

This product is NOT a toy. Please keep children away from this product.
This product is designed for indoor use only. Do NOT use outdoors.
Do NOT place this product near a heat source. Do NOT place it in an enclosure unless there is normal ventilation.
Do NOT attempt to repair this product by yourself. All repairs should be performed by an authorized professional.
This product is only suitable for improving the entertainment, and convenience of your home life and reminding you about the device status. It should NOT be used as security equipment for homes, buildings, warehouses or any other places. If a user violates the product use instructions, the manufacturer will NOT be liable for any risks and property losses.

Caution

Risk of explosion if the battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
Do not ingest battery, Chemical Burn Hazard.
This product contains a coin/button cell battery. If the coin/button cell battery is swallowed, it can cause severe internal burns in just 2 hours and can lead to death.
Keep new and used batteries away from children.
If the battery compartment does not close securely, stop using the product and keep it away from children.
If you think batteries might have been swallowed or placed inside any part of the body, seek immediate medical attention.
Disposal of a battery into a fire or a hot oven, or mechanically crushing or cutting of a battery, can result in an explosion.
Leaving a battery in an extremely high temperature surrounding environment can result in an explosion or the leakage of flammable liquid or gas.
A battery subjected to extremely low air pressure may result in an explosion or the leakage of flammable liquid or gas. The equipment is only suitable for mounting at heights ≤ 2 m.

Under normal use conditions, this equipment should keep a separation distance of at least 20cm between the antenna and the body of the user.

Declaration Of Conformity

EU Declaration of Conformity
Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Water Leak Sensor T1, WL-S02D] complies with Directive 2014/53/EU. The full text of the EU Declaration of Conformity is available at the following internet address: https://www.aqara.com/DoC/.

UK Declaration of Conformity
Hereby, [Lumi United Technology Co., Ltd] declares that the radio equipment type [Water Leak Sensor T1, WL-S02D] complies with Directive 2017 (SI 2017 No. 1206, as amended by SI 2019 No. 696). The full text of the UK Declaration of Conformity is available at the following internet address: http://www.aqara.com/DoC/.

WEEE Disposal and Recycling Information
All products bearing this symbol are waste electrical and electronic equipment (WEEE as in directive 2012/19/EU) which should not be mixed with unsorted household waste. Instead, you should protect human health and the environment by handing over your waste equipment to a designated collection point for the recycling of waste electrical and electronic equipment, appointed by the government or local authorities. Correct disposal and recycling will help prevent potential negative consequences to the environment and human health.

Please contact the installer or local authorities for more information about the location as well as the terms and conditions of such collection points.

The symbol on the product or its packaging indicates that this product may not be treated as household waste. Instead, it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment.

FCC ID:2AKIT-AS014
Federal Communications Commission (FCC) compliance statement:

This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
This device may not cause harmful interference, and
This device must accept any interference received, including interference that may cause undesired operation.
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note:
This equipment has been tested and found to comply with the limits for a Class B digital device, according to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit diﬀerent from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

RF Exposure statement:
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

IC:22635-AS014
IC NOTICE TO CANADIAN USERS

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject to the following two conditions:

This device may not cause interference.
This device must accept any interference, including interference that may cause undesired operation of the device.

This Class B digital apparatus complies with Canadian ICES‐003. This device complies with RSS‐247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20 cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Please read this manual carefully and keep it.