POWER CACHE 39602 HD Lithium Jump Starter Power Bank User Manual
- June 5, 2024
- POWER CACHE
Table of Contents
HD Lithium Jump Starter Power Ban
P/N 39602
User’s Manual
SAFETY WARNINGS AND GUIDELINES
Please read this entire manual before using this device, paying extra attention to these safety warnings and guidelines. Please keep this manual in a safe place for future reference.
- Do not leave the power bank unattended while charging.
- Do not use the power bank while it is being charged.
- Allow the power bank to cool for at least 15 minutes between each jump-start.
- Do not use the power bank with damaged clamps or a defective power plug.
- Do not allow children under 18 years of age to use the power bank without adult supervision.
- After performing a jump start, wait at least 30 minutes before attempting to charge the power bank.
- Always use the cables included with the power bank or certified replacement cables.
- Do not overcharge the internal battery.
- Do not smoke, strike a match, or cause a spark in the vicinity of the power bank.
- Only charge in a well-ventilated area.
- This power bank is not intended for use in a commercial repair facility.
- Store the power bank indoors in a cool, dry place when not in use
- This power bank is intended for temporary use outdoors. Reasonable care should be taken when using the power bank in wet conditions.
- This device contains a Lithium-ion battery. Dispose of this device only in accordance with local, state, or federal regulations for electronic waste.
- Clean using a soft, dry cloth only. Do not use chemical cleaners, solvents, or detergents. For stubborn deposits, moisten the cloth with warm water.
- This device has no user-serviceable parts. Do not attempt to open it, service, or modify this device
INTRODUCTION
This PowerCache™ HD Lithium Jump Starter Power Bank is rated to deliver up to 1,200 amps and features a 16,000mAh/59.2Wh lithium-ion battery. It has a USB Type-C® input/output and is charged using a USB-C® wall charger or another power source. It includes a set of PowerCache Smart Battery Clamps with built- in safety features, which are used to jump-start a vehicle with a dead battery. It also features two USB Type-A outputs for use in charging or powering USB devices, such as tablets, phones, etc., and an LED lamp for illumination. When used properly, this PowerCache HD Lithium Jump Starter Power Bank has been tested and certified for safety and performance by an accredited third-party laboratory to conform to UL® Standard 2743
CUSTOMER SERVICE
The Monoprice Customer Service department is dedicated to ensuring that your ordering, purchasing, and delivery experience is second to none. If you have any problem with your order, please give us an opportunity to make it right. You can contact a Monoprice Customer Service representative through the Live Chat link on our website www.monoprice.com or via email at support@monoprice.com. Check the website for support times and links
PACKAGE CONTENTS
Please take an inventory of the package contents to ensure you have all the
items listed below. If anything is missing or damaged, please contact
Monoprice Customer Service for a replacement.
1x PowerCache™ HD Lithium Jump Starter Power Bank
1x PowerCache Smart Battery Clamp Cable
1x USB Type-C® Charging Cable
1x Carry Case
1x User’s Manual
PRODUCT OVERVIEW
- Power Button
- Power/Battery Level Indicators
- Battery Clamp Cable Connector
- USB Type-A Output 2 Port
- USB Type-A Output 1 Port
- LED Lamp
- USB Type-C® Input/Output Port
- DC Output
CHARGING
Perform the following steps to charge the power bank. It should be charged for at least 3 hours before first use and at least once every 3 months to ensure the battery is fresh and capable of holding a full charge.
- Plug one end of the included USB Type-C® Cable into the USB Type-C Input/Output Port on the power bank.
- Plug the other end into a USB power source, such as a wall charger (not included). The Power/Battery Level Indicator will flash, indicating that charging is in progress.
OPERATION
Jump-Starting
This jump starter is only compatible with 12V engines up to 7.0L Gas/6.7L
Diesel in displacement. Using this product with larger displacement engines or
voltages other than 12V can cause serious personal injury, as well as damage
the device.
- Ensure the power bank has at least a 25% charge remaining. If less than 25% changed, it may not be able to start the engine. We recommend fully charging the power bank before performing a jump start.
- Attach the black clamp of the Battery Clamp Cable to the negative lead on the battery, then attach the red clamp to the positive lead.
- Plug the other end of the Battery Clamp Cable into the Battery Clamp Cable Connector on the power bank. The LED on the cable shows circling clockwise.
- Use your vehicle’s starter to start the engine. The LED on the cable should show the power bank’s current voltage. Note that the power bank will stop power output after20 seconds and the LED on the cable will flash
- Unplug the Battery Clamp Cable from the power bank within 30 seconds.
- Remove the red clamp from the battery’s positive lead, then remove the black clamp from the battery’s negative lead.
Notes:
- Never allow the red and black clamps to come into contact with each other.
- After successfully starting your vehicle, the power bank will automatically reset.
- Do not crank the engine more than 3 times in succession.
- If your vehicle fails to start, unplug the Battery Clamp Cable from the power bank, wait for 15 minutes, then reconnect the cable and try again to start the engine again.
Charging USB Devices
Perform the following steps to charge a USB device, such as a tablet, phone,
etc.
-
Plug one end of your device’s charging cable into one of the USB
Type-A Output Ports or into the USB Type-C® Input/Output Port for a USB-C® device, then plug the other end into your device’s charging port. -
Momentarily press the Power Button on the power bank to start charging.
Using the LED Lamp
- Press and hold the Power Button for about 3 seconds to turn the LED Lamp on.
- Momentarily press the Power Button to cycle through the Full On, Flashing , and SOS light modes.
- Press and hold the Power Button for about 3 seconds to turn the LED Lamp off.
FAULT PROTECTION INDICATIONS
Protection Function|
LED Indication
| Warning Sound
---|---|---
Reverse Polarity| | One ring per second
Short Circuit| | One ring per second
Reverse Charging| | One ring per second
Low Voltage 14.0 ±0.3V| | One ring per second
Over Voltage 17.5 ±0.3V| | Long buzz
Overheat| | One ring per second
SPECIFICATIONS
| Part Number | 39602 |
|---|---|
| Model | G21 |
| Battery Capacity | 16,000mAh/59.2Wh |
| Jump Start Voltage | 12V |
| Jump Start Current | 600A |
| Jump Peak Current | 1200A |
| USB Type-C® Input/Output | 5 VDC, 3A |
| USB Type-A Output 1 Power | 5 VDC, 3A or 9 VDC, 2A or 12 VDC, 1.5A |
| USB Type-A Output 2 Power | 5 VDC, 2.1A |
| DC Output Power | 12 VDC, 6A |
| Operating Temperature | +50 — +104°F (+10 — +40°C) |
| Dimensions | 7.6″ x 3.5″ x 1.4″ (193 x 89 x 36 mm) |
TECHNICAL SUPPORT
Monoprice is pleased to provide free, live, online technical support to assist
you with any questions you may have about installation, setup,
troubleshooting, or product recommendations. If you ever need assistance with
your new product, please come online to talk to one of our friendly and
knowledgeable Tech Support Associates. Technical support is available through
the online chat button on our website
www.monoprice.com or through email by sending a
message to tech@monoprice.com. Check the
website for support times and links.
REGULATORY COMPLIANCE
Notice for FCC
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference, and
- this device must accept any interference received, including interference that may cause undesired operation.
Modifying the equipment without Monoprice’s authorization may result in the equipment no longer complying with FCC requirements for Class B digital devices. In that event, your right to use the equipment may be limited by FCC regulations, and you may be required to correct any interference to radio or television communications at your own expense.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
Notice for Industry Canada
This Class B digital apparatus complies with Canadian ICES-003.
5011081
CONFORMS TO UL STD.2743
Monoprice™, PowerCache™, HyperJump™, the PowerCache logo, and all
Monoprice logos are trademarks of Monoprice Inc.
USB Type-C® and USB-C® are trademarks of USB Implementers Forum, Inc.
UL® and the UL logo are registered trademarks of UL LLC.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>