tekkiwear W3 Smartwatch User Manual

Tekkiwear W3 Smartwatch User Manual

Adaptation platform and requirements

Android 4.0 or higher & IOS 8.5 and above  Mobile phone hardware supports Bluetooth 4.0

Product diagram

Watch client download

Scan the QR code below to download and install the watch clienthttp://t9.fit/QcCAAA

Connect the watch

Operation guidance

Introduction to call function

You can make calls by connecting your phone’s Bluetooth to the watch
( Note : other functions must be connected to the mobile phone through the APP to be used )

Use attention points

1. If the watch has been connected by another mobile phone, please disconnect it on the original mobile phone and restore the factory settings once in the settings of the watch.
2. Please note that the Bluetooth name of the call connection is ‘W3″, (the Bluetooth device named ‘ W3 ” must not be connected here, otherwise there will be a problem that the secondary device cannot be searched when the APP is connected)
3. Please keep the call within 5 meters , otherwise the call quality will be affected.

Operation on the mobile phone: Setting s-Bluetooth-search for ·w3· after the connection is connected, you can make or receive calls.

Watch function introduction

Frequently asked questions and answers

Call and music player connection question s and answers If you need to play and answer calls through the watch, please connect the device with the W3 Bluetooth name in the mobile phone-settings-Bluetooth (if you can’ t use it after a period of time due to operational problems, you can also repeat the steps)

The shortlisted device found W3, after confirming that Bluetooth switch on the mobile phone has been turned on

• a. Please slide down on the top of the watch ( top drop-down menu)lettings-confirm that the phone is upon
• b. If necessary, if you still can’ t find it, please go to watch-settings-return to factory settings, and the to back to step 1 to a device connected to Bluetooth called W3

• 3. If the watch end leaves the phone during the delivery period, in order to achieve low power consumption and increase battery life, the watch will automatically disconnect from the phone, as shown in the figure below, it is displayed as u not connected

• 4. At this time, please pull down the menu -settings-call on the watch side, switch the switch once and then turn it on, the watch side will automatically reconnect with the phone.

Click to close the call function , and then click to call again to change the status to HONH again to re-enter the connection state.

• 5. The watch will automatically connect with the phone again

APP function introduction

1. “Daily” interface can view the number of steps, heart rate, sleep  and exercise date. :
2. In the “Device” interface, you can perform related settings and view the device connection.
3. “My” interface can be set for personal privacy.

Why does the blood pressure value deviate from the sphygmomanometer?

The deviation between the measured value of the watch and the sphygmomanometer is determined by many factors . The measurement position of the sphygmomanometer is the brachia! artery, and the measurement position of the watch is in the two main branches of the arterioles. Under normal circumstances, the aortic blood pressure measurement and the arteriole blood pressure measurement the value will vary by three to forty; if you use a watch and a sphygmomanometer to measure at the same time, because the blood flowing in the arteries is eccentric, the sphygmomanometer uses the strap below the middle of your elbow to be under pressure, temporarily blood unable to smoothly flow to the lower pulsating branch ; increased vascular tension, making the upper and lower blood pressure measurements more deviations.

Why can’ t I take a hot bath with my watch?

The temperature of the bath water is relatively high, it will produce a lot of water vapor, and the water vapor is mutually, it is molecular radius is small, it is easy to seep into the gap of the watch case, when the temperature drops, it will condense into liquid droplets again, it is easy to short circuit the internal circuit of the watch, damage the circuit board of the watch, and then damage the watch.

Why can’t the watch receive notifications?
Android phone settings:

1. Confirm that the message push switch is turned on on the mobile client
2. Confirm the message and then the mobile phone notification bar can be displayed normally, the watch message push is pushed by reading the message in the mobile phone notification bar, if there is no message in the mobile notification bar and the watch client ha no message, the watch will not be able to receive the push. (You need to find the notification settings in the phone settings and turn to on the notification switch of WeChat/phone/SMS/mobile client)
3. Open the accessibility settings of the watch client (Find the access ability in the phone settings, open the accessibility settings of the watch client)

Apple phone settings:

1. Confirm that the message push switch is turned on on the mobile client
2. The confirmation message can be displayed normally in the mobile notification bar (You need to find the notification settings in the phone settings and turn to on the notification switch of WeChat/phone/SMS/mobile client)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>