UNIVIEW 0235C7C6 Villa Door Station User Manual

UNIVIEW 0235C7C6 Villa Door Station

Packing List

Contact your local dealer if the package is damaged or incomplete. The package contents may vary with the device model.

2

|

Screw components

| 2    (for plastic model)

3    (for metal model)

|

Set

3| Tail cable| 1| PCS
4| Wall mount bracket| 1| PCS
5*| Embedded bracket| 1| PCS
6| Drill template| 1| PCS
7| Product Documents| 1| Set

Remarks

means optional and supplied with metal models only.

Appearance

The dimensions, structure, and tail cables may vary with the device model. The figures are only for illustrative purposes.

The cable specifications are as follows:

Connect RS485 interface

RS485_B| Yellow
GND| Black
ALM_IN1| Purple|

Connect alarm input interface

ALM_IN2| White/Purple
ALM_IN3| Light Green
ALM_IN4| Yellow/Black
GND| Black|

Connect power interface

VDD12V| Red
LOCK1_NC| Pink|

Connect door lock interface

LOCK1_COM| White/Yellow
LOCK1_NO| White/Green
LOCK2_NC| Gray
LOCK2_COM| White/Orange
LOCK2_NO| White/Blue
GND| Black|
---|---|---

Installation

Preparation

• Before installation, plan wiring for power cable, network cable, etc. The number of cables depends on the actual networking conditions.
• Please prepare the following tools:
  • Electric drill
  • Phillips screwdriver
  • Marker
  • Tape measure
  • ESD wrist strap or gloves
  • Glue gun

Installation Steps
The following figures are for reference only. The installation method may vary with scenarios.

Wall Mount

NOTE!

• (Optional) A junction box can be used for wall mount.
• (Optional) A sun shield can be used for a wall mount.

The above accessories should be self-prepared or purchased separately. Please consult your dealer or technical support for the recommended accessories specifications.

1. Mount the junction box (skip this step if no junction box). Use the existing junction box embedded in the wall or drill a hole to embed one. The two installation holes on the box should be parallel to the ground during installation. Paste the drill template.
   • With junction box: Align the two holes (A) on the drill template with the two installation holes on the junction box. See the left figure below.
   • Without junction box:
   1. Paste the drill template on the wall with the arrow perpendicular to the ground.
   2. Use a Ø6mm to Ø6.5mm drill bit to drill two 30 mm-depth holes on the A position (be careful not to damage cables in the wall).
   3. Insert the expansion bolts into the two holes.
2. Mount the bracket and sunshield.
3. Keep the two snaps on the bracket facing upward and the screw hole at the bottom of the bracket facing outward.
4. Tighten the bracket and sunshield.

  * With junction box: Align the screw holes of the bracket and sun-shield to those of the junction box, insert round tail cross screws, and tighten them.
  * Without junction box: Insert the pointed tail cross screws into the expansion bolts to fix the bracket and sunshield.

3. (Optional) Install the Micro SD card.

NOTE!
Please format the Micro SD card before use.

WARNING!
Do not hot-plug the Micro SD card, otherwise the door station or the SD card may be damaged.

Connect all the cables.

1. Use the Phillips screwdriver to loosen the screws on the rear panel, and then remove the panel.
2. Connect the network cable and other cables to the rear panel correctly, and then lead the cables out from the cable groove.
3. Fix the rear panel (with rubber cushion facing inward) onto the door station with screws.

Mount the door station onto the bracket.

1. Align the slots on the door station with the two snaps of the bracket, and then insert.
2. After the screw hole of the door station is aligned with the bracket hole, insert a Torx socket screw to fix the station and the bracket.

Embedded Mount

NOTE!

• Only metal door station supports embedded mount.
• The embedded bracket will be used for the embedded mount.
  (Optional) You can use an embedded sunshield for an embedded mount. Please consult your dealer or technical support for the recommended accessories specifications.

1. Fix the embedded bracket (hereinafter referred to as “bracket”).
   • Ensure that the wall has enough space to mount the bracket. The bracket size is as follows.
2. Lead two screws through the bracket holes to fix the bracket on the wall.
3. (Required for sun-shield mount) Mount the rubber plug on the protrusion of the bracket (shown in the figure), which can prevent the tamper-proof button of the  door station from continuously sounding due to loosening.
4. Loosen the screw at the station’s bottom to separate the front shell from the station.
5. (Optional) Insert the sunshield from the rear side of the station. As shown below.
6. (Optional) Install the Micro SD card. See Step 4 in Wall Mount for details.
7. Connect all the cables. See Step 5 in Wall Mount for details.
8. Fix the door station and the sunshield to the bracket.
9. Align the three holes of the station with those of the bracket, insert the screws and tighten.
10. Insert the screw into the bottom of the station again, and then tighten.

Startup

After the door station is installed correctly, you can use a network cable to connect the station to the PoE power supply or connect one end of the power adapter (user-purchased or prepared) to the power interface of the station and the other end to the main supply.

Web Login

The default network settings are shown in the table below and can be modified as Log in to the door station’s Web interface to perform management or maintenance operations required.

•  Gateway: 192.168.1.1

Note:

DHCP is enabled by default. If a DHCP server is deployed in your network, the door station may be assigned an IP address, and you need to use the assigned IP address to log in.

Username| admin
Password| 123456

Note:

The default password is intended only for your first login. To ensure security, please change the password after your first login. You are strongly recommended to set a strong password of at least nine characters including all three elements: digits, letters, and special characters. If the password is changed, use the new password to log in.

Follow these steps to log in to the Web interface:

• Open your Internet Explorer (IE9 and higher), input the IP address of the door station in the address bar, and then press Enter to open the login page.

NOTE!

You may need to install a plug-in at your first login (close all the browsers when the installation starts). Follow the on-screen instructions to complete the installation and then open the browser again.

• Enter the username and password, and then click Login.

Disclaimer and Safety Warnings

Copyright Statement
©2023 Zhejiang Uniview Technologies Co., Ltd. All rights reserved. No part of this manual may be copied, reproduced, translated, or distributed in any form or by any means without prior consent in writing from Zhejiang Uniview Technologies Co., Ltd (referred to as Uniview or us hereafter). The product described in this manual may contain proprietary software owned by Uniview and its possible licensors. Unless permitted by Uniview and its licensors, no one is allowed to copy, distribute, modify, abstract, decompile, disassemble, decrypt, reverse engineer, rent, transfer, or sublicense the software in any form or by any means.

Trademark Acknowledgements

Unvuniarch are trademarks or registered trademarks of Uniview. All other trademarks, products, services, and companies in this manual or the product described in this manual are the property of their respective owners.

Export Compliance Statement
Uniview complies with applicable export control laws and regulations worldwide, including that of the People’s Republic of China and the United States, and abides by relevant regulations relating to the export, re-export, and transfer of hardware, software, and technology. Regarding the product described in this manual, Uniview asks you to fully understand and strictly abide by the applicable export laws and regulations worldwide.

EU Authorised Representative
UNV Technology EUROPE B.V. Room 2945,3rd Floor,Randstad 21-05 G,1314 BD,Almere,Netherlands.

Privacy Protection Reminder
Uniview complies with appropriate privacy protection laws and is committed to protecting user privacy. You may want to read our full privacy policy on our website and get to know the ways to process your personal information. Please be aware, that using the product described in this manual may involve the collection of personal information such as face, fingerprint, license plate number, email, phone number, and GPS. Please abide by your local laws and regulations while using the product.

About This Manual

• This manual is intended for multiple product models, and the photos, illustrations, descriptions, etc, in this manual may be different from the actual appearances, functions, features, etc, of the product.
• This manual is intended for multiple software versions, and the illustrations and descriptions in this manual may be different from the actual GUI and functions of the software.
• Despite our best efforts, technical or typographical errors may exist in this manual. Uniview cannot be held responsible for any such errors and reserves the right to change the manual without prior notice.
• Users are fully responsible for the damages and losses that arise due to improper operation.
• Uniview reserves the right to change any information in this manual without any prior notice or indication. Due to such reasons as product version upgrades or regulatory requirements of relevant regions, this manual will be periodically updated.

Disclaimer of Liability

• The product described in this manual is provided on an “as is” basis. Unless required by applicable law, this manual is only for informational purposes, and all statements, information, and recommendations in this manual are presented without warranty of any kind, expressed or implied, including, but not limited to, merchantability, satisfaction with quality, fitness for a particular purpose, and non-infringement.
• To the extent allowed by applicable law, in no event shall Uniview’s total liability to you for all damages for the product described in this manual (other than as may be required by applicable law in cases involving personal injury) exceed the amount of money that you have paid for the product.
• Users must assume total responsibility and all risks for connecting the product to the Internet, including, but not limited to, network attacks, hacking, and viruses. Uniview strongly recommends that users take all necessary measures to enhance the protection of network, device, data, and personal information. Uniview disclaims any liability related thereto but will readily provide necessary security-related support.
• To the extent not prohibited by applicable law, in no event will Uniview and its employees, licensors, subsidiary, and affiliates be liable for results arising out of using or inability to use the product or service, including, not limited to, loss of profits and any other commercial damages or losses, loss of data, procurement of substitute goods or services; property damage, personal injury, business interruption, loss of business information, or any special, direct, indirect, incidental, consequential, pecuniary, coverage, exemplary, subsidiary losses, however caused and on any theory of liability, whether in contract, strict liability or tort (including negligence or otherwise) in any way out of the use of the product, even if Univiewhas been advised of the possibility of such damages (other than as may be required by applicable law in cases involving personal injury, incidental or subsidiary damage

Network Security

Please take all necessary measures to enhance network security for your device. The following are necessary measures for the network security of your device:

• Change the default password and set a strong password: You are strongly recommended to change the default password after your first login and set a strong password of at least nine characters including all three elements: digits, letters, and special characters.
• Keep firmware up to date: It is recommended that your device is always upgraded to the latest version for the latest functions and better security. Visit Uniview’s official website or contact your local dealer for the latest firmware.
• The following are recommendations for enhancing the network security of your device:
• Change password regularly: Change your device password on a regular basis and keep the password safe. Make sure only the authorized user can log in to the device.
• Enable HTTPS/SSL: Use an SSL certificate to encrypt HTTP communications and ensure data security.
• Enable IP address filtering: Allow access only from the specified IP addresses.
• Minimum port mapping: Configure your router or firewall to open a minimum set of ports to the WAN and keep only the necessary port mappings. Never set the device as the DMZ host or configure a full cone NAT.
• Disable the automatic login and save password features: If multiple users have access to your computer, it is recommended that you disable these features to prevent unauthorized access.
• Choose username and password discretely: Avoid using the username and password of your social media, bank, email account, etc, as the username and password of your device, in case your social media, bank, and email account information is leaked.
• Restrict user permissions: If more than one user needs access to your system, make sure each user is granted only the necessary permissions.
• Disable UPnP: When UPnP is enabled, the router will automatically map internal ports, and the system will automatically forward port data, which results in the risk of data leakage. Therefore, it is recommended to disable UPnP if HTTP and TCP port mapping have been enabled manually on your router.
• Multicast: Multicast is intended to transmit video to multiple devices. If you do not use this function, it is recommended you disable multicast on your network.
• Check logs: Check your device logs regularly to detect unauthorized access or abnormal operations.
• Isolate video surveillance network: Isolating your video surveillance network with other service networks helps prevent unauthorized access to devices in your security system from other service networks.
• Physical protection: Keep the device in a locked room or cabinet to prevent unauthorized physical access.
• SNMP: Disable SNMP if you do not use it. If you do use it, then SNMPv3 is recommended.

Learn More

You may also obtain security information under the Security Response Center at Uniview’s official website.

Safety Warnings
The device must be installed, serviced, and maintained by a trained professional with the necessary safety knowledge and skills. Before you start using the device, please read through this guide carefully and make sure all applicable requirements are met to avoid danger and loss of property.

Storage, Transportation, and Use

• Store or use the device in a proper environment that meets environmental requirements, including but not limited to, temperature, humidity, dust, corrosive gases, electromagnetic radiation, etc.
• Make sure the device is securely installed or placed on a flat surface to prevent falling.
• Unless otherwise specified, do not stack devices.
• Ensure good ventilation in the operating environment. Do not cover the vents on the device. Allow adequate space for ventilation.
• Protect the device from liquid of any kind.
• Make sure the power supply provides a stable voltage that meets the power requirements of the device. Make sure the power supply’s output power exceeds the total maximum power of all the connected devices.
• Verify that the device is properly installed before connecting it to power.
• Do not remove the seal from the device body without consulting Uniview first. Do not attempt to service the product yourself. Contact a trained professional for maintenance.
• Always disconnect the device from power before attempting to move the device.
• Take proper waterproof measures by requirements before using the device outdoors.

Power Requirements

• Install and use the device in strict accordance with your local electrical safety regulations.
• Use a UL-certified power supply that meets LPS requirements if an adapter is used.
• Use the recommended cord set (power cord) in accordance with the specified ratings.
• Only use the power adapter supplied with your device.
• Use a mains socket outlet with a protective earthing (grounding) connection.
• Ground your device properly if the device is intended to be grounded.

Battery Use Caution

• When battery is used, avoid:
  • Extremely high or low temperature and air pressure during use, storage, and transportation
  • Battery replacement.
• Use the battery properly. Improper use of the battery such as the following may cause risks of fire, explosion, or leakage of flammable liquid or gas.
  • Replace the battery with an incorrect type;
  • Dispose of a battery in a fire or a hot oven, or mechanically crushing or cutting a battery;
• Dispose of the used battery according to your local regulations or the battery manufacturer’s instructions.

Regulatory Compliance

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. Visit http://en.uniview.com/Support/Download_Center/Product_Installation/Declaration/ for SDoC Caution: The user is cautioned that changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 20cm between the radiator and any part of your body.

LVD/EMC Directive
This product complies with the European Low Voltage Directive 2014/35/EU and EMC Directive 2014/30/EU.

WEEE Directive–2012/19/EU
The product this manual refers to is covered by the Waste Electrical & Electronic Equipment (WEEE) Directive and must be disposed of responsibly.

Battery Directive-2013/56/EU
The battery in the product complies with the European Battery Directive 2013/56/EU. For proper recycling, return the battery to your supplier or to a designated collection point.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>