RECTORSEAL GDLDOME2000 Guardian Dome D-Lock Instruction Manual

: June 17, 2024
: Rectorseal

Table of Contents

RECTORSEAL GDLDOME2000 Guardian Dome D-Lock
Specifications
Product Usage Instructions
FAQ
Installation Instructions
Read User Manual Online (PDF format)
Download This Manual (PDF format)

RECTORSEAL GDLDOME2000 Guardian Dome D-Lock

Specifications

Models Available: GDLDOME2000, GDLDOME3000, GDLDOME4000
Manufacturer: RectorSeal

Product Usage Instructions

Installation:

Clean the floor sink of debris and grime build-up within the throat of the drain.
Determine the appropriate size Guardian Dome-D-Lock to be installed: 2, 3, or 4.
Once size is determined, follow the specific installation instructions provided for your chosen model.

Monitoring the Dome-D-Lock:

Ensure that the Dome-D-Lock is properly secured and locked. It should only need to be removed for sanitation purposes.
If cleaning is required, use hot soapy water and a plastic brush to clean any built-up grime or debris. For thorough cleaning, wash it by hand or run it through your dish machine.
Before re-installing, inspect all parts to ensure they are in good condition.
Monitor that your Guardian Dome-D-Locks are secured/locked in place once a month to guarantee protection of your drain pipes.

FAQ

Q: How often should I clean the Dome-D-Lock?

A: The Dome-D-Lock should be monitored and cleaned as needed for sanitation purposes. For thorough cleaning, it is recommended to clean it once a month.

Q: Can I use harsh chemicals to clean the Dome-D-Lock?

A: It is recommended to use hot soapy water and a plastic brush for cleaning. Avoid using harsh chemicals that may damage the product.

Installation Instructions

TOOLS NEEDED:

The following tools to properly secure the Guardian Dome-D-Lock:

3/8″ Ratchet
3/8″ Ratchet Extension
Tamperproof Torx Key (GDLT40 for 2″ and GDLT45 for 3″ & 4″ drain locks)
Rag

HOW TO INSTALL

Clean the floor sink of debris and grime build up within the throat of drain. (Photo #1)
Determine the appropriate size Guardian Dome-D-Lock to be installed: 2″, 3″ or 4″. Once size is validated, place the Dome-D-Lock in the hole of the floor sink.
Note: If the drain lock has too tight of a fit, the rubber banding can be removed.
Assemble the ratchet, ratchet extension and tamperproof key. Determine which tamperproof key will be needed to secure the desired Dome-D-Lock. GDLT40 key for 2″ and GDLT45 for 3″ and 4″.
While holding down the Dome-D-Lock with one hand, insert the driver and key into the tamperproof bolt and tighten (clockwise) until firmly secured. Do not over tighten. (Photo #2)

MONITORING THE DOME-D-LOCK

Once the Dome-D-Lock is properly secured and locked, there should be no need to remove it other than for sanitation purposes. As needed, use hot soapy water and a plastic brush to clean any built up grime or debris. If the Dome-D-Lock is to be removed for cleaning, wash it by hand or run it through your dish machine. Before re-installing, make certain all parts are in good condition.
Monitor that your Guardian Dome-D-Lock is are secured/locked in place once a month to guarantee protection of your drain pipes.

Manufactured by

RectorSeal, LLC 2601 Spenwick Drive, Houston, TX 77055,

3255 Wyandotte St. East, Windsor, ON N8Y 1E9, Canada • 519-966-4901 A CSW Industrials Company. RectorSeal, the logos and other trademarks are property of RectorSeal, LLC, its affiliates or its licensors and are protected by copyright, trademark and other intellectual property laws, and may not be used without permission. RectorSeal reserves the right to change specifications without prior notice. ©2023 RectorSeal. All rights reserved. R51071-0823

Limited Warranty

For more information on our product warranty, visit