WAGNER Attachment Wood and Metal Extra Gravity Spray Instruction Manual

: June 17, 2024
: Wagner

Table of Contents

WAGNER Attachment Wood and Metal Extra Gravity Spray
Product Usage Instructions
Gravity spray attachment
Start-up
Shutting down and cleaning
2 years guarantee
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

WAGNER Attachment Wood and Metal Extra Gravity Spray

WAGNER-Attachment-Wood-and-Metal-Extra-Gravity-Spray-product-
image

Specifications:

Designed for applying water-soluble paints, lacquers, and spray films
Not suitable for wall paints (dispersion and latex paints)
Container capacity: 600 ml and 150 ml
Gravity feed system
Material quantity regulation feature
2 years warranty

Product Usage Instructions

Preparation of the Coating Material:

Stir the material and pour the required amount into the paint container.
Dilute the material as per the manufacturer’s recommendation if needed.

Start-up :

Insert the container into the gun body and fasten it with the bayonet catch.
Connect the gun body with the Click & Paint handle.
Place the gun on a level surface with the stand folded out.
Fill the container only when attached to the gun to prevent leaks.
Fill the container with the prepared coating material.
Attach the valve hoses to the container cover and gun body.

Adjusting the Material Quantity:
Set the material volume by turning the regulator on the trigger guard of the spray gun.

Lower material volume: Turn anti-clockwise (-)
Higher material volume : Turn clockwise (+)

Selecting the Spray Setting :
WARNING! Danger of injury! Never pull the trigger guard while adjusting the air cap.

Slightly unscrew the union nut, then turn the air cap to the desired spray setting position.
Tighten the union nut after selecting the spray setting.

FAQ :

Q: What types of materials can be sprayed with this attachment?
A: The attachment is suitable for water-soluble paints, lacquers, and spray films. It is not recommended for wall paints like dispersion and latex paints.
Q: How should I adjust the material quantity for spraying?
A: You can adjust the material volume by turning the regulator on the trigger guard. Turn anti-clockwise for lower volume and clockwise for higher volume.

Gravity spray attachment

General instruction

Read the operating instructions carefully before using the tool and observe the safety instructions. Keep the operating instructions in a safe place.
The Gravity Feed spray attachment was developed for applying water-soluble paints and lacquers as well as paints and lacquers containing solvents. It is also suitable for processing spray film. Wall
paints (dispersion and latex paints) cannot be processed.
CAUTION!
- The units may only be used with a functional valve. If paints rises in the ventilating hose (Fig. 1 , item 7) do not operate the unit further!
- Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary.
- Do not place the spray gun on the side.
- Do not combine components from different spray attachments. The parts could be damaged.

Description (Fig. 1)

Union nut| 2) Air cap
Nozzle| 4) Seal
Stand (fold-out)| 6) Container (600 ml)
Ventilating hose with valve| 8) Container (150 ml)
O-ring| 10) Gun body
Trigger| 12) Material quantity regulation
Container seal|

Preparation of the Coating Material
The Standard spray attachment can be used to spray paints, varnishes and glazes that are undiluted or slightly diluted. Detailed information is available in the technical data sheet of the manufacturer ( Internet download).

Stir the material up and put the required amount into the paint container.

Thinning recommendation

Sprayed material|
Glazes| undiluted
Wood preservatives, mordants, oils, disinfection agents, plant protective agents| undiluted
Paints containing solvents and water-soluble paints, primers, spray films, vehicle coating paints, thick-film glazes| dilute by 0 – 10% (undiluted with Flexio)

If the convey capacity is too low, add 5 – 10% dilution step-by-step until the convey capacity fulfills your requirements (observe maximum permissible dilution according to manufacturer’s instructions).

Start-up

Insert container into gun body and fasten by turning with bayonet catch. (Fig. 2)
Connect gun body with Click & Paint handle (not included).(Fig. 3)
Place the gun on a level surface with the stand folded out.
Fill the container only if it is attached to the gun, otherwise the coating material will leak.
Remove the container cover.
Fill container with prepared coating material.
Close container with cover.
Attach the valve hoses to the container cover and gun body.(Fig. 4)

Adjusting the material quantity (fig. 5)
Set the material volume by turning the regulator on the trigger guard of the spray gun.

lower material volume turn anti-clockwise (-)
higher material turn clockwise (+)

Selecting the spray setting
WARNING! Danger of injury! Never pull the trigger guard while adjusting the air cap.

With the union nut (fig. 6, 1) slightly unscrewed, turn the air cap (2) to the desired spray setting position (arrow). Then tighten the union nut.

Fig. 7 A = vertical flat jet for horizontal surfaces
Fig. 7 B = horizontal flat jet for vertical surfaces
Fig. 7 C = circular jet for corners, edges and hard-to-reach surfaces

Interruption of Work
When processing 2-component varnishes, clean the device immediately.

Shutting down and cleaning

Switch the unit off.
Unscrew the container cover and fill the remaining coating material back into the original container.
Pour water or solvent into the container. Do not use flammable materials for cleaning purposes.
Close the container again.
Spray the water or solvent into a container or a cloth.
Repeat the above procedure until the water or solvent emerging from the nozzle is clear.
Turn off the machine and remove the plug.
CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects. The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe.
If the valve is soiled with paint, it must be cleaned. To do this, unplug the hose, split it and remove the diaphragm. Carefully clean all parts or replace if necessary. (Fig. 8)
The unit may only be operated with an integer diaphragm. When assembling, insert the diaphragm with the pin pointing downwards.
Unscrew the union nut and remove the air cap and nozzle. Clean the air cap, nozzle seal and nozzle with a brush and solvent or water.
Push the nozzle seal (Fig. 9, 4) over the needle (14); the groove (slot) should point towards you.
Put the nozzle (Fig. 9, 3) onto the gun body and find the correct position by turning it.
Put the air cap (Fig. 10, 2) onto the nozzle (3) and tighten it using the union nut (1). $WAGNER-Attachment-Wood-and-Metal-Extra-Gravity-Spray- $13$$

Spare Parts List (Fig. 1)

Australia (AUS) version order no. in brackets

| 2362877

AUS (2361747)

3| Nozzle| 2361238
4| Seal| 0417706
6| Container 600 ml with cover| 2410208
7| Valve complete with hose| 2410217
8| Container 150 ml with cover| 2410210
9| O-ring| 2362875

The CLICK&PAINT SYSTEM with additional spray attachments and accessories offers the right tool for each work.
Further information about the WAGNER range of products for renovating is available under www.wagner-group.com
Environmental protection

The appliance and accessories should be recycled in an environmentally friendly way. Do not dispose of the appliance with household waste. Support environmental protection by taking the appliance to a local collection point or obtain information from a specialist retailer.

Important Note regarding Product Liability!
Using other accessories and spare parts can lead to partial or total loss of liability and guarantee claims. With original WAGNER accessories and spare parts, you have the guarantee that all safety regulations are fulfilled.

2 years guarantee

The guarantee runs for two years, counting from the date of sale (sales slip). It covers and is restricted to free-of-charge rectification of faults which are demonstrably attributable to the use of faulty materials in manufacture, or assembly errors; or free-of-charge replacement of the defective parts. The guarantee does not cover incorrect use or commissioning or fitting or repair work which is not stated in our operating instructions. Wearing parts are also excluded from the guarantee. The guarantee excludes commercial use. We expressly reserve the right to fulfil the guarantee. The guarantee expires if the tool is opened up by persons other than WAGNER service personnel. Transport damage, maintenance work and loss and damage due to faulty maintenance work are not covered by the guarantee. Under any guarantee claim, there must be proof of purchase of the tool through submission of the original receipt. Wherever legally possible, we exclude all liability for injury, damage or consequential loss, especially if the tool has been used for a purpose other than that stated in the operating instructions, commissioned or repaired other than in accordance with our operating instructions or if repairs are performed by someone who is unqualified. We reserve the right to perform any repairs in excess of those stated in our operating instructions. In case of guarantee or repair, please refer to your point of sale.

WAGNER SPRAYTECH (UK) LTD