KENTON ROLAND JUNO 6 MIDI Retrofit Instructions
- June 17, 2024
- KENTON
Table of Contents
User instructions for Kenton MIDI retrofit for
ROLAND JUNO 6
These instructions are only for Juno 6 MIDI retrofit kits produced after
1March 2006 Firmware JN605100 or later
N.B. Different instructions apply to earlier Kenton Juno 6 MIDI retrofit kits.
USING THE MIDI INTERFACE
When you turn on the synthesizer for the first time, you will be in omni-off
mode channel 1 for receive and also channel 1 for transmit – See the following
pages for other factory default settings. When you select a receive channel,
this will be stored in memory and will be remembered for when you subsequently
turn on the synth – all parameters listed on the next page are stored.
If you want to put the machine back to the factory default settings at any
time, switch the synth on whilst holding the red push button pressed – hold
for a couple of seconds then release.
RED PUSH BUTTON
Three modes are available by pushing the red push button during normal playing mode. Before you press the red button however, make sure that no keys are pressed on either the Juno 6 or the remote MIDI keyboard otherwise the results may be unpredictable. The key presses can be entered on the Juno 6’s own keyboard, or from the remote MIDI keyboard.
-
PROGRAM CHANGE MODE
For sending program changes from the keyboard. Press the red push button once only (short press – then release), any key then selects a program change which it sends through the MIDI Out. When the key is released, you are then automatically returned to playing mode. For example a short press on the red push button followed by bottom C will send program change #0 whereas top C will send #60. (Nothing is stored in non-volatile memory after this operation) -
SET-UP MODE
For setting MIDI channels and assignments. Give the red push button two short presses (half a second each) – then release. Follow this with a key or sequence of keys as detailed on page 2. After making a MIDI channel assignment, you will be automatically returned to playing mode but after making other assignments you will need to press the ENTER key (Top C) to return to playing mode. This is to enable you to make the multiple key presses required when re-assigning Sources to Destinations. (N.B. all set-ups are stored in non volatile memory). -
TRANSPOSE MODE / ARPEGGIO CLOCK DIVIDE SETTING MODE
Press and hold the red push button for about four seconds – then release. Middle C will sound on the synth and continue to sound until you press a key. The key that you press on the remote keyboard will be the new middle C for MIDI IN. You can set any value up to two octaves up or down – settings outside this range will be ignored (where middle C = no transposition) . Note that transpose mode cannot be entered from set-up mode. (N.B. the transposition will be stored in non volatile memory).
The bottom four octaves on a 61 note remote keyboard are used to set “transpose” but the top octave will set the arpeggio divide.
G = Set triplet on (can be used with any of below)
Ab = Clock divided by 8 (eighth speed)
A = Clock divided by 4 (quarter speed)
Bb = Clock divided by 2 (half speed)
B = Clock normal – no divide (full speed)
TOP C = Enter – return to normal playing & store new setting
For more information on the operation of the arpeggio clock with MIDI, see
note #11 further on.
Function of keys during set-up mode: 
ASSIGNING MIDI CONTROL SOURCES TO DESTINATIONS
| SOURCE | DEFAULT DESTINATION |
|---|---|
| Pitch-bend wheel | Pitch-bend |
| Modulation wheel (cc#1) | Modulation |
| Aftertouch | Modulation |
| Velocity | —- |
Controller X (def cc#16)
Controller Y (def cc#17)| VCF / Filter cutoff
MIDI Volume (cc#7)| VCA / Volume
-
To assign sources to destinations,
a) press the red push button twice to enter set-up mode
b) select a source by using one of the keys A to Eb (see table on previous page)
c) [optionally if the source is Controller X or Y, you can assign a controller to it now – see below] d) select destinations OFF to de-select previous assignments for this source
e) select destinations ON to make new assignments for this source
f) either hit Top C to enter/exit, or select a new source and make assignments for that [go back to b] -
Controllers X & Y can be assigned to any continuous controller (cc). By default controller X is assigned to cc#16, and controller Y is assigned to cc#17. To re-assign either of them, first press the red push button twice to enter SET-UP mode. Next press the Db or D key (see table on previous page) to select the X or Y controller source, then send a MIDI message of the required continuous controller. Then either press top C to enter / exit, or use some of the destination keys to assign what this controller will control.
– For example to set controller Y to respond to cc#4, press the red button twice, press D, send a cc#4 message to the Juno 6 from another synth or MIDI controller, then press top C to enter /exit. [or select another function] -
Sources can have multiple destinations, so for example controller X could be assigned to control both filter and volume at the same time, should you want it to.
-
Where pitch-bend wheel is the source, only the bend wheel UP will affect destinations other than pitch-bend.
Also where pitch-bend is the destination, sources other than pitch-bend wheel will only bend the pitch UP. -
Receive channel setting will return you directly to playing mode, all other keys will let you stay in SET-UP mode until you press the ENTER key (Top C).
-
The ENTER key (Top C) also performs a “reset all controllers” function – OFF in most cases, but ON for volume, and centre for pitch bender.
-
If you want to put the MIDI back to the default settings at any time, switch the synth on whilst holding the red push button pressed – hold for a couple of seconds then release.
-
During set-up mode, the retrofit will receive on ALL MIDI channels.
-
List of continuous controllers (cc) recognised – (numbers in decimal)
01 modulation wheel
07 Main volume
64 sustain pedal
121 reset all controllers 123 all notes off
124 omni mode off (always poly) 125 omni mode on (always poly)
126 (mono mode) = all notes off 127 (poly mode) = all notes off
nnn Controller X (user defined where nnn = any controller) (default = cc#16)
nnn Controller Y (user defined where nnn = any controller) (default = cc#17) -
List of other commands recognised – (numbers in hexadecimal)
8nH notes off 9nH notes on & velocity
BnH continuous controller (see above)
DnH channel pressure (aftertouch) EnH pitch-bend change
FEH active sensing -
Using arpeggio clock. With the rear panel toggle switch in the UP position, the Juno 6 will function as normal.
With the switch in the DOWN position the Juno 6 will use MIDI clock. You may need to set the divide rate – see the first page. If you want to use the external jack input for clock, you should set the switch in the up position.
To select MIDI clock merely set the rear panel switch to the DOWN position and
the arpeggiator will take its tempo from MIDI. Note that if the switch is set
to MIDI and there is no MIDI clock present, the Juno 6 will not play, if it is
in arpeggio mode.
To change the divide rate, press the push button and hold in for about four
seconds, until a note sounds, (this is transpose mode) the bottom four octaves
are used to set “transpose” but the top octave will set the arpeggio divide.
TOP C = ENTER – Return to normal playing and store
B = Clock normal – no divide (full speed)
Bb = Clock divided by 2 (half speed)
A = Clock divided by 4 (quarter speed)
Ab = Clock divided by 8 (eighth speed)
G = Set triplet on (can be used with any of above)
You will need to press TOP C (Enter) after any selection.
If you want to use Triplet, you will need to set this after the divide ratio,
as pressing any of the divide ratios cancels Triplet.
GENERAL INFORMATION ABOUT MIDI CONNECTIONS
Any MIDI IN should be connected to a MIDI OUT or a MIDI THRU similarly any
MIDI OUT should be connected only to a MIDI IN and any MIDI THRU should also
only be connected to a MIDI IN.
MIDI OUT (if fitted) is the signal from the synthesizer (or drum machine etc.)
that is to be sent to another instrument. MIDI IN is a received signal that
contains MIDI information from another synth, and MIDI THRU is an exact copy
of information arriving at the MIDI IN socket. This allows several instruments
to be connected together.
If you want to wire your own MIDI cables the following information may be
useful.
- Although a 5 pin connector is used, only two connections plus an earth connection are required.
- If you look at the din plug from the wiring side you will see that the pins are numbered. From left to right (or clockwise) these are 1 – 4 – 2 – 5 – 3.
- The pins numbered 1 & 3 are not used.
- The screen (earth) is connected to pin 2 (centre pin)
- Pin 4 of one plug should be connected to pin 4 of the other
- Pin 5 of one plug should be connected to pin 5 of the other
- You should now have a working MIDI lead
- It is preferable to label one end of the cable MIDI IN & the other end MIDI OUT, to avoid confusion.
WARRANTY
All Kenton MIDI Kits come with a 12 month (from purchase date) back to base warranty, (i.e. customer must arrange and pay for carriage to and from Kenton Electronics). Note that kits should be fitted as soon as possible after purchase, as the retrofit kits are in a continuous state of development.
Kenton Electronics Limited
Unit 3, Epsom Downs Metro Centre,
Waterfield, Tadworth, KT20 5LR, UK
Tel: +44 (0)20 8544 9200
Fax: +44 (0)20 8544 9300
www.kenton.co.uk
Copyright (c) KENTON Electronics & John Price 1986-2023
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>