YOLINK YS7905-UC Water Depth Sensor User Guide
- June 12, 2024
- YOLINK
Table of Contents
Water Depth Sensor
YS7905-UC
Quick Start Guide
Revision May. 10, 2023
Welcome!
Thank you for purchasing YoLink products! We appreciate you trusting YoLink
for your smart home & automation needs. Your 100% satisfaction is our goal. If
you experience any problems with your installation, with our products or if
you have any questions that this manual does not answer, please contact us
right away. See the Contact Us section for more info.
Thank you!
Eric Vanzo
Customer Experience Manager
The following icons are used in this guide to convey specific types of
information:
Very important information (can save you time!)
Before You Begin
Please note: this is a quick start guide, intended to get you started on the
installation of your Water Depth Sensor.
Download the full Installation & User Guide by scanning this QR code:
Installation & User Guide
https://www.yosmart.com/support/YS7905-UC/docs/instruction
You can also find all current guides and additional resources, such as videos
and troubleshooting instructions, on the Water Depth Sensor Product Support
Page by scanning the QR code below or by visiting:
https://shop.yosmart.com/pages/water-depth-sensor-product-support Product
Support Support produit Soporte de producto
Your Water Level Monitoring Sensor connects to the internet via a YoLink hub
(SpeakerHub or the original YoLink Hub), and it does not connect directly to
your WiFi or local network. In order for remote access to the device from the
app, and for full functionality, a hub is required. This guide assumes the
YoLink app has been installed on your smartphone, and a YoLink hub is
installed and online (or your location, apartment, condo, etcetera, is already
served by a YoLink wireless network).
Included
|
---|---
4 x Cable Tie Mount| 8 x Cable Tie
|
Quick Start Guide| 1 x ER34615 Battery Pre-Installed
Required Items
The following items may be required:
|
---|---
Screws and Anchors| Medium Phillips Screwdriver
|
Drill with Drill Bits| Double-sided Mounting Tape
Get to Know Your Water Depth Sensor
LED
Behaviors
| Blinking Red Once, Then Green Once
Device Start-Up
---|---
| Blinking Red And Green Alternately
Restoring to Factory Defaults
| Blinking Red Once
Updating Water Depth
Measurement
| Quick Blinking Green
Control-D2D Pairing in Progress
| Quick Blinking Red
Control-D2D Unpairing in
Progress
| Slow Blinking Green
Updating
| Fast Blinking Red Once Every 30 Seconds
Low Battery, Replace Batteries Soon
Power Up
Install the App
If you are new to YoLink, please install the app on your phone or tablet, if
you have not already. Otherwise, please proceed to the next section.
Scan the appropriate QR code below or find the “YoLink app” on the appropriate
app store.
|
---|---
Apple phone/tablet iOS 9.0 or higher| Android phone/ tablet 4.4 or higher
http://apple.co/2Ltturu| http://bit.ly/3bk29mv
Open the app and tap Sign up for an account. You will be required to provide a
username and a password. Follow the instructions, to set up a new account.
Allow notifications, when prompted.
You will immediately receive a welcome email from no-
[email protected] with some helpful information.
Please mark the yosmart.com domain as safe, to ensure you receive important
messages in the future.
Log in to the app using your new username and password.
The app opens to the Favorite screen.
This is where your favorite devices and scenes will be shown. You can organize
your devices by room, in the Rooms screen, later.
Refer to the full user guide and online support for instructions on the use of
the YoLink app.
Add Your Water Depth Sensor to the App
-
Tap Add Device (if shown) or tap the scanner icon:
-
Approve access to your phone’s camera, if requested. A viewfinder will be shown on the app.
-
Hold the phone over the QR code so that the code appears in the viewfinder. If successful, the Add Device screen will be displayed.
-
Follow the instructions to add your Water Depth Sensor to the app.
Install the Water Depth Sensor
Sensor use considerations:
The Water Depth Sensor measures the depth of water in a tank or container
using a pressure sensor in the probe. The weight of the water is sensed by the
probe, and this data is converted to water depth in the app. Therefore, the
probe must be placed at the bottom of the tank or container it is used.
Sensor location considerations:
Before installing your Water Depth Sensor, consider the following important
factors:
- The sensor body is designed for outdoor use, but it must not be submerged; do not install the sensor where it can possibly be submerged later. Internal water damage to the sensor is not covered by the warranty.
- The sensor has a SET button and LED indicator that should be accessible; install the sensor at an accessible location.
Install the Water Depth Sensor’s Probe
-
Uncoil and suspend the probe into the water container. The probe should sit on the bottom of the container, in a vertical orientation as shown in the diagram.
-
When the correct position is attained, secure the probe cable to the container sidewall, lid, or other fixed and stable surface, so that the probe position does not change. You can use cable ties and mounts to secure the probe cable, but to avoid damaging the cable, do not overtighten the ties or otherwise pinch or crimp the cable.
Install the Water Depth Sensor (Main Assembly)
Determine how you will mount the sensor to the wall or surface, and have
hardware and anchors appropriate for the wall surface on hand. The sensor is
intended to be wall-mounted, using screws. It can be placed in another
enclosure. If using alternative methods, such as mounting tape, ensure the
sensor is securely installed, so as to not fall off the wall later (physical
damage is not covered by the warranty).
- Holding the sensor in position, mark the location of the sensor’s two mounting holes to the wall surface.
- If using anchors, install them, per the manufacturer’s instructions.
- Insert and tighten one screw in each of the sensor’s mounting holes, ensuring the sensor is secured to the wall or mounting surface.
Refer to the full installation and user guide and/or the product support page, to complete the settings in the YoLink app.
Contact Us
We are here for you, if you ever need any assistance installing, setting up or
using a YoLink app or product!
Need help? For fastest service, please email us 24/7 at
[email protected]
Or call us at 831-292-4831 (US phone
support hours: Monday – Friday, 9AM to 5PM Pacific)
You can also find additional support and ways to contact us at:
www.yosmart.com/support-and-service Or scan the QR code: Finally, if you have any feedback or suggestions
for us, please email us at [email protected]
Thank you for trusting YoLink!
Eric Vanzo
Customer Experience Manager
15375 Barranca Parkway
Ste. J-107
Irvine, California 92618
© 2023 YOSMART, INC IRVINE,
CALIFORNIA