VOLT VHS-650 Ultra Premium Cast Brass Up Down Instruction Manual
- June 17, 2024
- VOLT
Table of Contents
VOLT VHS-650 Ultra Premium Cast Brass Up Down
Specifications:
- Product Model: VHS-650
- Power Supply : Transformer rated maximum of 300 watts at 15 volts
- Main Low Voltage Cable: Intended for shallow burial – less than 6 inches (152 mm)
- Manufacturer Contact : www.voltlighting.com or call 1-813-978-3700
Product Usage Instructions:
Remove Lens:
Twist the top and bottom lens to remove them from the luminaire.
Install Bulb and Lens:
- Insert the bulbs (sold separately) with the correct wattage and type marked on the luminaire label.
- CAUTION: Do not exceed the maximum wattage marked on the luminaire label.
- NOTE: DO NOT touch the bulb with bare hands. Use a soft cloth to handle the bulb.
- Tighten the lenses back onto the fixture body.
Remove Luminaire from Wall Mount:
Remove the mounting screws off the top and bottom of the luminaire and take out the luminaire from the wall mount.
Install Wall Mount:
- Place the wall mount at the desired location and mark two points on the wall surface for the wall anchors.
- Drill proper holes on the wall.
- Insert the wall anchors into the drilled holes, pass the main low-voltage supply cable through the centre hole on the wall mount, attach it to the wall, and secure it with lock screws.
Wire Connection:
Using two wire connectors (sold separately), connect the supply wires from the fixture to the main low-voltage supply cable leads.
Install Luminaire:
Carefully tuck all wires into the wall mount. Attach the back of the luminaire over the wall mount and secure it by threading the mounting screws onto the top and bottom of the luminaire body.
Frequently Asked Questions (FAQ):
- Q: Can I use a power supply exceeding 300 watts with this luminaire?
- A: No, this luminaire is intended to be used only with a power supply rated maximum of 300 watts at 15 volts. Exceeding this limit may damage the product.
- Q: How do I handle the bulbs during installation?
- A: Do not touch the bulbs with bare hands. Use a soft cloth to handle them to prevent damage or reduce their lifespan.
IMPORTANT: PLEASE READ BEFORE INSTALLATION
This luminaire is intended for installation in accordance with local codes and
the National Electric Code (NEC). Failure to adhere to these codes and
instructions may result in serious injury, property damage and void the
warranty.
These instructions do not intend to cover all variations in installation,
operation maintenance or mounting situations.
- Make sure that the power is turned OFF before installing or servicing this luminaire.
- WARNING: risk of electrical shock. Install all luminaires 10 feet (3.05M) or more from pool, spa or fountain.
- This luminaire is intended to be used only with a power supply (transformer) rated maximum of 300 watts (25 AMPS) at 15 volts.
- Listed wire nuts must be suitable for wet locations and wiring connections must be made with UL listed wire connectors that are suitable for outdoor use.
- Position the low voltage wire and wire connector so that it is located within 6 inches (15.2 cm) from a building structure, a luminaire or fitting.
- The main low-voltage cable is intended for shallow burial – less than 6 inches (152 mm).
- If additional lengths of low-voltage cable are required, please contact www. voltlighting.com or call 1-813-978-3700.
IMPORTANT SAFETY INSTRUCTIONS
INSTRUCTIONS ON THE RISK OF FIRE, OR INJURY TO A PERSON’S LIGHTED LAMP IS HOT!
WARNING – To reduce the risk of FIRE OR INJURY TO PERSONS.
- Turn off/unplug and allow to cool before reducing the lamp.
- The lamp gets HOT quickly!
- Do not touch the hot lens, guard or cowl.
- Keep lamps away from materials that may burn.
- Do not touch the lamp at any time.
- Use a soft cloth.
- Oil from the skin may damage the lamp.
- Do not operate the fixture with a damaged or missing lens or shield.
PACKAGE CONTENTS
- Wall Mount
- Mounting Screws
- Wall Anchors
- Luminaire
PRODUCT DIMENSIONS
REMOVE LENS
Twist the top and bottom lens to remove them from the luminaire.
INSTALL BULB AND LENS
Insert the bulbs (sold separately) with the correct wattage and type marked on
the luminaire label.
CAUTION : Do not exceed maximum wattage marked on the luminaire label.
NOTE : DO NOT touch the bulb with bare hands. Use a soft cloth to handle
the bulb.
Tighten the lenses back onto the fixture body.
Remove Luminaire from the Wall Mount
Install Wall Mount
Place the wall mount at the desired location and mark two points on the wall
surface for the wall anchors. Remove the wall mount and drill the proper holes
on the wall.
Insert the wall anchors, into the drilled holes. Pass the main low-voltage
supply cable through the centre hole on the wall mount and attach it to the
wall. Secure with the lock screws. Hand tighten until snug.
Wire Connection
Using two wire connectors (sold separately) connect the supply
wires from the fix-ture to the main low-voltage supply cable leads.
INSTALL LUMINAIRE
Carefully tuck all the wires into the wall mount. Attach the back of the luminaire over the wall mount. Secure it by threading the mounting screws onto the top and bottom of the luminaire body.
INSTALL/REPLACE BULB
Remove the lens assembly of the luminaire body to expose the bulb and replace
it with the correct wattage and type marked on the luminaire label. Reinstall
the lens assembly.
IMPORTANT: Halogen bulbs must be protected from moisture and dust at all
times. Always reinstall the shade and lens when removed.
CONTACT
- 1-813-978-3700
- Mon-Fri 8 am-8 pm • Sat-Sun 10 am – 6 pm (EST) Specifications and product details are subject to change without notice. © Copyright 2023, VOLT® Lighting, Lutz FL USA 33549
- All rights reserved.
- customersupport@voltlighting.com
- www.voltlighting.com
References
- Factory Direct Landscape Lighting | VOLT® Lighting
- Factory Direct Landscape Lighting | VOLT® Lighting
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>