SANODUSCHA FIBABRB01V1 Freestanding Bathtub Instruction Manual

SANODUSCHA FIBABRB01V1 Freestanding Bathtub

Product Information

Specifications

• Model : FIBABRB01V1.0
• Type : Freestanding Bath
• Capacity : Not specified
• Material : Not specified

Product Usage Instructions

Before Installation

Before starting the installation process, ensure that all fittings are provided. Place the assembled bath on a mat to prevent damage to the bath surface. This product requires a two-person lift using proper lifting techniques. It is recommended to fit a bath waste to the bath before installation. If you are unsure about the installation process or waste connection, consult a qualified tradesperson. Ensure compliance with the council and local authority by-laws for all installations.

Installation Procedure

1. Place the bath upside down on a dust sheet or soft cloth to protect the surface. Level the feet on the base of the bath and lock them into place.
2. Turn the bath over and position it in its final location in the bathroom. Use a spirit level to check alignment and adjust the feet if needed.
3. Turn the tub upside down and install a drain line according to your home’s sewer configuration.
4. Turn the bath right side up and rest it on blocks to access and attach household pipework.
5. Once the waste option is chosen and attached to the household pipework, pour water through the waste to check for leaks. Apply silicone underneath the bath for a finished look.

After Installation

After installation, run water into the bath and inspect connections for any leaks.

Care & Cleaning

For cleaning, use a soft cloth or sponge with mild soap and water. Avoid scouring pads or abrasive cleaners as they may damage the surface. Do not use disinfectants or ammonia concentrates. Periodically, polish the bath with LIBRA acrylic polish to restore its sheen.

FAQ

• Q: Can I use abrasive cleaners on this product?
  • A : No, avoid using abrasive cleaners as they may dull the surface of the bath.
• Q: How long should I wait before using the bath after applying silicone?
  • A : Allow 24 hours for the silicone to dry off before using the bath.

CAUTION

• Risk of personal injury. Bathtubs can be extremely heavy. Obtain sufficient help to carefully lift or move the bathtub.
• Risk of property damage. Make sure that a watertight seal exists on all bath drain connections.

TOOLS

YOU MIGHT NEED

BEFORE INSTALLATION

• Before installation check that all fittings have been supplied.
• Assembled bath on a mat to protect against damage to bath surface. This product requires a two-person lift-use proper lifting techniques.
• This installation guide recommends a bath waste be fitted to the bath prior to installation – if any doubt about Installation and waste connection
• please consult a qualified tradesmen
• Follow each step in turn.

IMPORTANT :All installations must comply with council and local authority by-laws. It is the responsibility of the installer to ensure that the waste is made watertight by means of silicone sealant or caulking compound.
NOTE : Bath can be installed after the wall & floor tiling is completed. Bath drain supplies should be arranged preliminarily according to the selected bath.

WARNING

• CAUTION
  • Ensure the floor where the bath will sit is level.
  • The waste & overflow is supplied with the product, however, other items required such as a waster trap and connectors are not supplied and must be purchased and must be purchased separately.
  • Because of the technical features of the product it should only be used with the waste & overflow supplied.
  • Handgrips for this product are not available.
  • The bathtub must be carried upside down, do not life or support the bath by the sides.

Prior to installation, the bath should be checked for damage as we recommend all work is to be carried out by a qualified person.

INSTALLATION PROCEDURE

1. Place the bath upside down on a dust sheet or soft cloth so as not to scratch the surface. Level the feet on the base of the bath and lock them into place.
2. Turn the bath over and temporarily place it in what will be the final position in the bathroom. Check along the top of the bath using a spirit level and adjust the feel if necessary and lock it into place.
3. Turn the tub upside down and install a drain line in the tub according to your home’s sewer configuration
4. Turn the bath the right way up and rest on two blocks(ideally 4”x4”)in position to gain access underneath to attach the household pipework.
5. Once the waste option has been chosen and attached to the household pipework water should be poured through the waste to check for leaks. Once this has been done apply silicon to the underside of the bath to complete the look.
6. Please allow 24 hours for the silicon to dry off before use. The installation guide includes options for waste connection: The final decision about installation and waste connection should be taken by a qualified person.

AFTER INSTALLATION

Run water into the bath and check connections for leaks.

CARE & CLEANING

• Use a soft cloth or sponge for cleaning.Do not use any scouring pads like pot clean-ers etc. as this will dull the surface
• Use mild soap and water for everyday use.
• Do not use any abrasive cleaning materials.
• Do not use any disinfectants, aerosol cleaners, ammonia concentrates, etc.
• Every few months give your bath a light polish with LIBRA acrylic polish to restore the original sheen.

CARE AND MAINTENANCE MANUAL

• ALWAYS
  • Clean every day by thoroughly rinsing with mild soap and warm water and wiping dry with a cloth.
  • Keep the tub free of any standing water as this can cause a buildup of mineral deposits, which can affect the appearance of your sink.
  • Always rinse the bathtub after using any cleaning agent and wipe dry with a cloth. Clean any mineral deposits that built up over time with a mild solution of vinegar and water followed by thorough flushing with water.

NEVER

• Use steel wool or a scouring pad as it damages the sink surface and causes discoloration.
• Let household cleaning agents or bleach sit in your bathtubs for a long period as this may ruin the finish of your sink.
• Leave rubber mats, sponges, or cleaning pads in the bathtub for long periods as this may damage the finish of your tub.
• Use the inside of the tub as a cutting surface.

NOTE

• The uneven surface — To finish polishing a bathtub, we usually apply max to make it shine and protect it from stains and scratches. However, the extra wax will eventually generate an uneven Surface. Before using it , please use a clean cloth with warm water in circular motions to lightly wipe the surface to remove the extra wax.
• The water stain — To finish testing the bathtub overflow, we usually inspect the bathtub overflow drains by running water down the drains to test if there is any leak at the overflow. Therefore, water stains may be found on the surface of the bathtub.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>