AKUVU Rechargeable Smart Barking Collar User Manual

User Manual Rechargeable Smart Barking Collar

Smart Dog Bark Control Collar
Read and fully understand this manual before use

Important Safety Information

• DO NOT leave the collar on the dog for more than 12 hours per day.
• When possible, re-position the collar on the dog’s neck every 1 to 2 hours.
• Check the fit to prevent excessive pressure; follow the instructions in this manual.
• Never connect a lead to the collar; it will cause excessive pressure on the contacts.
• Wash the dog’s neck area and the Metal Prongs of the collar weekly with a damp cloth.
• For the comfort of your dog, please choose the Prong Covers of the proper length and wear them to the Metal Prongs before use.

Product Information

Test The Product

1A Charge the Bark Control Collar before useDescription of Charging
When the product is on charge. the Battery Bar blinks from left to right and the Indicator blinks fast.
When the product is fully charged. Battery Bar stop blinking and the Indicator becomes solid.
A warning tone will be delivered if the product is on charge with an improper charger.
Note:

1. The improper charger means one with an output voltage over 5V.
2. Use the magnetic charging cable in the package when charging. Other magnetic charging cables may not be suitable for this product and may cause electric damage.
3. The Charger, Power Bank and other charging devices shown in the above pictures are not included in the box.

1B Power onthe Bark Control Collar1C Set the Bark Control Collar to Test Mode, the display will show digit 0.
After that, imitate a dog bark towards the Sensor Mic located at the back of the product (the Sensor Mic is under the strap and you don’t need to take off the strap to test when itis dressed up).1D The Bark Control Collar Responds at the Test Mode:If the product responds as cescr bed above. you’ve succeeded In setting up the Bark Control Collar properly

Put the Product on Your Dog

Note: have a look if you have a small dog! Please ensure to fit the product snugly, yet loose enough to allow one finger to fit between the strap and your dog’s neck. Note

1. The stimulation may not work if your dog has long hair, itis sometimes necessary to trim the hair around the Metal Prongs and to use the longer Metal Prongs and Prong Covers.
2. The hexagon hole on the Test Bulb Tool can be used to fasten or unfasten the Metal Prongs to the Contact Points.

Great! Now you have successfully put the Bark Control Collar on your dog and it’s ready for training.

Mode Setting

The following instruction will guide you on how to switch modes.

1. Power on the product by pressing and holding the Power/Set Button for 2 seconds
2. Press the Mode Button to switch modes, the mode icons will be changed
3. 4 Modes:

Variable Warning Tone Mode 6 Variable Warning Tone of different frequencies in 6 steps| Vibration Mode 3 levels of Vibration in 3 steps
---|---
Variable Warning Tone+ Vibration Mode 6 Variable Warning Tone+3 levels of Vibration Working collaboratively in 6 steps| Variable Warning Tone+ Vibration Mode +Shock Mode 6 Variable Warning Tone+3 levels of Vibration+ 6 levels of Shock Working collaboratively in 6 steps

Indicator & Display

Indicators

How It Works

Icon Description:

NOTES:

1. The product will go to the next step if your dog keeps barking within 1 minute.
2. The product will automatically go back to Step 1 if itis not activated within 1 minute.

CONTACT US:

In the process of using the product, if you encounter any problems, you can contact the online customer service to provide you with solutions.
TEL: 1-866-663-6767
Website: www.akuvu.net
Email: AkuvuService@Gmail.com
Monday through Friday, 8:00am — 5:00pm PT

Frequently Asked Questions Answers

Q: Why doesn't the product work when the dog barxs?

A: Please first ensure to fit the product snugly, yet loose enough to allow one finger to fit between the strap and your pet’s neck. Some dogs have weak barking, and in this case, you will need to level up the sensitivity level. A thick coat on the neck area may also have a small chance to decrease the sensing from the barking. Please trim the coat near the area where you place the product.

Q: Why is the product triggered saretimes in a noisy env ronment though the dog isn't barking?

A: Though we have optimized the barking detection to the best, some environment noises may have a similar frequency to barking, which may have a small chance to activate the product. Please lower the sensitivity level.

Q: Can I use the product when otner dogs are p aying avound?

A: Dogs will bark when playing and get excited. For the comfort and safety of your pet, we don't suggest using this product in such an environment.

Q: How dol know if I can usetris product formy dog?

A: The product is designed for healthy dogs over 6 months old. Most importantly, this product cannot be used on unhealthy or aggressive dogs, and if you are unsure whether this product is appropriate for your pet. please consult your veterinarian or a certified trainer.

Q: Can this product stop my dag s howl?

A: No, this Bark Control Collar is designed to detect the barking only. It cannot detect or stop the howling.

Q: Can I charge this product with any type of charger?

A: No, you are suggested to charge this product with a charger of 5V output voltage. because a charger with an output voltage over 5V may cause damage to the product. The product will stop charging automatically if the input voltage becomes too high and deliver a warning tone.

Q: Will my dog stop barkirg comp etely?

A:The Bark Control Collar effectively and humanely stops all barking when it is worn. It should only be worn during periods of unwanted barking.

Q: Is the Bark Control! Collar safe and humane?

A: Yes. The Bark Control Collar is designed to get your dog's attention, not to punish him. However, the initial Static Shock correction may startle your dog.

****Troubleshooting

Doesn’t Work

1. Please turn it on and check if the left and right green indicators flash when itis in standby.
2. Please adjust the sensitivity before using it again (5-evel sensitivity, 5-level is the most sensitive)
3. Check the MIC hole for blockage and clean if necessary.
4. Please wear the device on the dog’s neck near the mouth.
5. If the problem persists, please contact us for assistance.

Doesn’t Charge

1. Please check if the charger currently being used outputs a voltage of 5V or less. If you hear a“beep beep” warning sound while charging, it means that your charger is outputting a voltage higher than 5V, triggering the product’s over voltage protection.

2. Please switch to another charging method, such as a computer USB or power bank

3. Please check if the charging magnetic contact points are clean and in good contact.
   If there is dirt, it needs to be cleaned.

4. If the issue still persists, please contact us to replace the charging cable.

Doesn’t Turn On

1. After charging, try to turn it on again (press and hold the power button for 2 seconds to turn it on) (there are two buttons at the bottom of the product, a power button and a mode M button, please distinguish them).
2. Contact us for assistance.

Goes off with Other Dogs Barking

1. Try to lower the sensitivity level (refer to the sensitive use card in the package)
2. If itis still triggered by mistake, please contact us to solve it.

Certification Statements

**** This device complies with Part 15 of the FCC Rules.
Operation is subject to the following two conditions

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Warning: Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority too perate the equipment.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
** Consult the dealer or an experienced radio/TV technician for help.
The company declares under its own responsibility that this product complies with the basic requirements of CE(2014/30/EU) and RoHS (2011/65/EU).
Without the approval of our company or the distributor, unauthorized changes or modifications to the equipment may violate the CE regulations, may cause the user to lose the right to operate the equipment, and invalidate the warranty.
Recycling Information &Battery Disposal
**Please observe the regulations for electronic and electrical devices to be disposed of in the respective country. In some countries or regions, this device must be recycled. If this device is no longer required, it must not be disposed of with normal municipal waste.
Separate collection of spent batteries required in many regions; check the regulations in your area before discarding spent batteries. For more recycling information, please refer to local regulations.

Model: S2
Version:1.0
Made inP.R.C

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>