Insta360 Triple Suction Cup Car Mount Instructions

: June 17, 2024
: Insta360

Table of Contents

Insta360 Triple Suction Cup Car Mount
Product Usage Instructions
What’s Included
Specifications
Installation
Steps
Disclaimer
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Insta360 Triple Suction Cup Car Mount

Insta360-Triple-Suction-Cup-Car-Mount-product

Specifications

Weight: 976g (34.4oz)
Suction Cup Diameter: 7.3cm (2.9inch)
Material: aluminum alloy, carbon fiber, plastic, rubber

Product Usage Instructions

Installation
Place the three suction cups where you wish to install the mount, adjusting the angle as you attach the support rods. After adjustment, press the suction cup air pump to fix the suction cups into place. Then via the knob, lock the adapter in place, using the horizontal support rod and the expansion support rod to hold the mount together.

Steps

Install the suction cups on the horizontal support rod.
- Loosen the knobs, slide the 2 suction cup adapters 1 into the horizontal support rod, and tighten the knobs 2 to complete the assembly.
Install the suction cups.
- The suction cup comes with an anti-slip bar. Slide the suction cup 3 into the chute of the adapter and tighten the knob 4 to complete the assembly.
Install your Insta360 Action Invisible Selfie Stick (sold separately).
- Insert the bottom of the selfie stick 5 into the middle locking hole of the horizontal support rod and tighten the knob 6 to complete the assembly.
Install the expansion support rod and the suction cups.
- Loosen the knob of the expansion support rod, then install it onto the first section 7 of the selfie stick, locking the knob 8 to secure the stick and installation. After fixing the expansion support rod, slide the suction cup 9 into the chute of the expansion support rod, then tighten the knob 10 to complete the assembly.
Check the stability of the Triple Suction Cup Car Mount carefully. If you find no leakage or issues with stability, you can start shooting.

FAQ

Q: What is the warranty period for the product?
A: The warranty period of the attached product is 3 months from the original retail purchase. Warranty service may vary according to the applicable laws of your state or jurisdiction. For detailed warranty policies, please visit https://insta360.com/support.

What’s Included

$Insta360-Triple-Suction-Cup-Car-Mount- $1$$

Specifications

Weight : 976g (34.4oz)
Suction Cup Diameter : 7.3cm (2.9inch)
Material : aluminum alloy, carbon fiber, plastic, rubber

Installation

Place the three suction cups where you wish to install the mount, adjusting the angle as you attach the support rods. After adjustment, press the suction cup air pump to fix the suction cups into place. Then via the knob, lock the adapter in place, using the horizontal support rod and the expansion support rod to hold the mount together.

Steps

Install the suction cups on the hoirzontal support rod.
Loosen the knobs, slide the 2 suction cup adapters 1 into the horizontal support rod, and tighten the knobs 2 to complete the assembly.
Install the suction cups.
The suction cup comes with an anti-slip bar. Slide the suction cup 3 into the chute of the adapter and tighten the knob 4 to complete the assembly. $Insta360-Triple-Suction-Cup-Car-Mount- $2$$
Install your Insta360 Action Invisible Selfie Stick (sold separately).
Insert the bottom of the selfie stick 5 into the middle locking hole of the horizontal support rod and tighten the knob 6 to complete the assembly.
Install the expansion support rod and the suction cups.
Loosen the knob of the expansion support rod, then install the onto the first section 7 of the selfie stick, locking the knob 8 to secure the stick and installation.
After fixing the expansion support rod, slide the suction cup 9 into the chute of the expansion support rod, then tighten the knob 10 to complete the assembly.
Check the stability of the Triple Suction Cup Car Mount carefully. If you find no leakage or issues with stability, you can start shooting.
If it is found that the suction cup is loosely sticking, press the suction cup with your hand and continuously press the piston rod to fix the suction cup more firmly to the surface.

$Insta360-Triple-Suction-Cup-Car-Mount- $3$$

Notes

Please assemble the Triple Suction Cup Car Mount according to the instructions above and do not use with any other accessories. If malfunction or damage is caused by failure to follow the instructions in this document, the warranty will be void.
This Triple Suction Cup Car Mount can only be used with Insta360 Action Invisible Selfie Stick, do not use with other selfie sticks.
It is recommended to use this product in the environment of 0°C – 40°C (32°F – 104°F).
Try to install all three suction cups on the same surface. If they cannot be installed on the same plane, the suction cups on both sides of the horizontal support rod must be applied on the same plane, and the suction cup on the expansion support rod must be installed on another suitable surface to provide adequate support.
Before installing the suction cup, ensure that the surface of the car or area is smooth and clean.
When installing the suction cups, ensure that the suction cups are fully attached to the surface. If they are unable to attach fully, try to release the knob, adjust the angle of the suction cups, install and retighten.
The white area on the suction cup’s rod is the indicator line. After the suction cup is installed, observe this indicator line. If the indicator line returns to the outside of the pump within a short period of time (the indicator line can be seen on the outside), it means there is a leakage, and the suction cup needs to be reinstalled.
After installing the Triple Suction Cup Car Mount, ensure that all knobs on the mount are tightened. If a knob cannot be tightened, or after all knobs are tightened, there is a misalignment or potential leakage, the expansion support rod or selfie stick will not correctly lock, and the mount is not ready for use.
During driving, or when stopping to rest, check the suction cup for any accidental air leakage (if you see the indicator line on the outside). If the suction cup has air leakage, reapply the suction cups to prevent the mount from falling and damaging the camera.
When removing the suction cup, pry the edge of the suction cup with your fingers to create a gap at the joint of the suction cup and the absorption plane, then remove the suction cup easily.
After use, if the surface of the suction cup is dirty, clean it promptly to ensure that the suction cup can maintain sufficient application force for the next use.
When installed with the Triple Suction Cup Car Mount, do not use your vehicle in excessively rugged off-road conditions (including but not limited to very bumpy and steep mountain roads with large stones), vehicle speed should not exceed 100km/h (62mph);
The suction cups in this product are a modular design. When a single suction cup is used, it can only be connected to the Insta360 Action Invisible Selfie Stick, keep the selfie stick in a contracted state and do not extend the selfie stick.

Disclaimer

Please read this Disclaimer carefully. Using this product means that you acknowledge and accept the terms of this disclaimer. By using this product, you hereby acknowledge and agree that you are solely responsible for your own conduct when using this product and any consequences thereof. You agree to use this product only for proper and lawful purposes. You understand and agree that Arashi Vision Inc. (hereinafter referred to as ‘Insta360’) accepts no liability for any and all misuse, consequences, damages, injuries, penalties, or any other legal responsibility directly or indirectly incurred by your using this product. Before every use, make sure that your product is functioning properly. If there’s any damage or irregularity, stop using it immediately. Within the scope of state laws and regulations, Insta360 reserves the right of final explanation and revision for the commitment.

After-Sales Service
The warranty period of the attached product is 3 months from the original retail purchase. Warranty service may vary according to the applicable laws of your state or jurisdiction. For detailed warranty policies, please visit https://insta360.com/support.

Arashi Vision Inc.
ADD: 11th Floor, Building 2, Jinlitong Financial Center, Bao’an District, Shenzhen, Guangdong, China