DELL P7524QT 5 Inch Ultrawide 4K UHD Touch Screen Monitor Instructions
- June 17, 2024
- Dell
Table of Contents
DELL P7524QT 5 Inch Ultrawide 4K UHD Touch Screen Monitor
Specifications
- Product Model: DELL P7524QT
- Screen Size: Not specified
- Resolution: Not specified
- Material: Various components as detailed below
Product Material Information:
The DELL P7524QT monitor contains various materials that should be disposed
of or recovered separately in compliance with EU Council Directive 75/442/EEC:
- Capacitors/Condensers
- Mercury-containing components
- Batteries
- Printed circuit boards (with a surface greater than 10 squarecm)
Components containing toner, ink, and liquids
Tools Required
List of tools required for disassembly:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
Disassembly Procedures
-
S1 Turn off power..
-
Unplug external cables(power cable and video cable) from the monitor.
-
Use a screwdriver to remove 8pcs screws for releasing the handles. (Torque:15±0.5kgf). Remove 60pcs screws for unlocking the rear cover(Torque: 3±0.3kgf).
-
Remove the handles and rear cover, then use a screwdriver to remove 7pcs screws for releasing the PC box.(Torque: 4.5±0.3kgf)
-
Remove the handles and rear cover, then remove the 5pcs rubbers as the picture below shown.
-
Use a screwdriver to remove 10pcs(4+6) screws for releasing the PC box.(Torque:3±0.3kgf)
-
Remove 2pcs O/C mylar tapes away from the back bracket, then remove 22pcs black tapes and 1pcs conductive tape as the picture below shown.
-
Disconnect all the cables as the picture below shown. Use a screwdriver to remove 2pcs screws for unlocking AC power outlet.(Torque: 4.5±0.5kgf)
-
Use a screwdriver to remove 8pcs screws for unlocking speakers. (Torque: 6kgf±0.5)
DELL P7524QT -
Use a Hex-head screwdriver to remove 4pcs screws for unlocking VGA connectors. (Torque: 4.5kgf±0.3) Use a screwdriver to remove 12pcs screws for unlocking the USB board, IO holder and main board, remove 16pcs screws for locking the power board, driver board, touch board and T-Con board. (Torque: 4.5kgf±0.3)
Disconnect the FFC cables away from the T-con board. -
Use a screwdriver to remove 42pcs screws (left: 11pcs, right :11pcs, top: 10pcs, bottom: 10pcs) for unlocking 4pcs strips.(Torque: 6±0.3kgf)
-
Use a screwdriver to remove 2pcs screws for unlocking the key board and the holder with strip.(Torque: 2±0.3kgf)
-
Use a screwdriver to remove 14pcs screws for unlocking the front bezels(top, left, right, bottom).(Torque: 3±0.3kgf)
-
Disconnect the touch cable and FFC cables. Use a screwdriver to remove13pcs screws(Torque: 6±0.3kgf), 12pcs screws (Torque: 3±0.3kgf) for unlocking the ED holder with the assembled unit.
-
Tear off 12pcs conductive foams on the specific position of the O/C SB, then release the O/C SB away from the back bracket.
-
Turn over the panel module with the bracket for screen faced up. Use a thin film(such as Prism film) to disassemble the O/C with glass carefully, then remove the O/C with glass and put then on a protective cushion.
-
Use a tripper to lift up the unit, then use a screwdriver to remove 10pcs screws for unlocking the ED unit , then use the tripper to put down the unit. (Torque: 3.0±0.3kgf)
-
Use a ED holder fixture to fix the ED holders, then lift up the ED holder unit for removing the ED unit, and then put the unit on a protective cushion.
-
Use a screwdriver to remove 24pcs screws for unlocking the bottom-middle bezel and then remove the bottom-middle bezel.(Torque: 2±0.3kgf)
DELL P7524QT
-
Remove 1pcs DEBF film, 1pcs Diffuser film, 1pcs LGP, 1pcs Reflector film away from the back bracket.
-
Use a screwdriver to remove 17pcs screws for unlocking the L/B heat sink with the back bracket. (Torque: 3±0.3kgf)
-
Use a screwdriver to remove10pcs screws for unlocking the two VESA brackets with back bracket.(Torque: 5±0.3kgf)
-
Remove electrolyte capacitors (red mark) from printed circuit boards.
DELL P7524QT
-
S23-1 Cut the glue between bulk cap. and PCB with a knife.
-
S23-2 Ensure cutting path within the glue, don’t touch bulk cap. or PCB.
-
S23-3 Cut into the bottom of bulk cap. and pullit up carefully.
-
S23-4 Take out bulk cap. pin solder with soldering iron and absorber.
-
S23-5 Lift the bulk cap. up and away from the PCB.
DELL P7524QT
Product material information
The following substances, preparations, or components should be disposed of or recovered separately from other WEEE in compliance with Article 4 of EU Council Directive 75/442/EEC.
Tools Required
List the type and size of the tools that would typically can be used to disassemble the product to a point where components and materials requiring selective treatment can be removed.
Tool Description:
- Screwdriver (Phillip head) #1
- Screwdriver (Phillip head) #2
- Penknife
- Soldering iron and absorber
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>