User Manual
M300S

service@azdome.hk

Important Safety Information

Thankyou for purchasing this AZDOME dashcam
This instruction manual containsinformation on howto operate yourdashcam Before using your dashcam, we recommend thatyou read through this manual to ensure correct usage.
Toimprove the performance of the product, the contents of this manual are subject to change without prior notice.

• Do not disassemble, repair, or modify the product yourself.
  Doing so may cause fire, electricshock, or malfunction. For internal inspection and repair, contact the service center.

• If any foreign matter gets inside the product, detach the power cord immediately.
  Contact the service center for repair.

• Do not adjust the product while driving.
  Doing so may cause an accident. Stop or parkour carina safe place before installing and setting up the product.

• Do notinstall the product in a location where the product can interfere with the driver’s field of vision.
  Doing so may cause an accident.

• Do not use a damaged or modified power cord. Only use the cords provided by the manufacturer.
  Damaged or modified power cords may cause an explosion, fire, or malfunction.

• Do not operate the product with wet hands.
  Doing so may cause electric shock

• Do not install the production an environment with high humidity, or combustible gases or liquids.
  Doing so may cause an explosion and/or fire.

• Do not leave the product near infants, children, or pets.
  There is arisk of them swallowing small components, and/or their saliva may get into the product, causing an explosion due toashortcircuit.

• Do not spray water or wax directly onto the product while cleaning the inside of the car.
  Doing so may cause fire, electric shock, or malfunction “If smoke or an unusual smell is emitted from the power cord, detach the power cordimmediately.
  Contact the service center or your distributor.

• Keep the terminals of the power cord clean.
  Failure to do so may cause excessive heat and fire.

• Use the correct input voltage.
  Failure to do so may cause explosion, fire, or malfunction.

• Plugin the power cord firmly so that it cannot easily be disconnected.
  Failure to do so may cause fire

• Donor cover the product with any material.
  Doing so may cause external deformation of the product or fire.
  Use the product and peripherals in a well-ventilated location

Warranty and Support

The AZDOME dash cam comes with a full 12 months warranty.
If you have any questions regarding your product, please do not hesitate to contacts at service@azdome.hk. Queries are typically answered within 12-24 hours Azidoes firmly committed to always improving our products, services, and user experience. If you have any thought son how we can do even better, we welcome your constructive feedback and suggestions.

Packing List

Check the box for each of the following items before installing the dash cam

Note

• Toimprove the performance of the product, the contents of this manual are subject to change without prior notice.

Specification

1920×1080 30 -1920×1080 30P + 1920×1080 30
GPS Track| Built-in
WiFi| Built-in (2.4GHz /5GHz Dual band)
USB Port| Charging and Storage
Power Interface| 5V/2.5A
Operation Temperature| -20°C to 70°C
---|---
Storage Temperature| -30°C~+85°C

Getting Started

of Tips Please read and understand tips before operating.

• Setting Date & Time: Please calibrate the date/time based on ‘your location under the TIME ZONE SETTING by going trap system settings menu, please refer to page EN-54
•  Before first time use, you MUST format the memory carding the camera to prevent any errors and for smooth operation, please reefer to page EN-56
• Make sure to always keep the camera plugged into power, because camera’ s adapts super capacitor, if no power supply iddahs cancan’ towering.
• You will need to insert a Micro-SD card before you can start recording. Please insert only a brand name Class-10 or above  higher speed Micro-SD card.

  | Description

  ---|---
  1| Sticker Mount
  2| Front Camera
  3| Micro-SD Card Slot
  4| Micro USB Charging Port
  5| WiFi Key
  Short Press 3 times in a row to shift between from 2.4GH TO 5GHZ.
  -Press and Hold for 3 seconds to turn on/off WiFi
  -Press once to shift from “Charge Mode” to “Storage Mode” when connected to USB Cable that can transfer data(NOT INCLUDED)
  -Press and Hold for 10 seconds to Format Micro-SD Card and set to default settings
  6| Rear Camera Slot (AV-IN)
  ---|---
  7| Recording LED Indicator
  8| GPS LED Indicator
  9| Mic-phone
  10| Reset Button
  11| Speaker
  12| Rear Camera

Installation

Installs front camera behind the rearview mirror. Install the
rear camerata the top of the back windshield. Remove any foreign matter and clean and dry the windshield before installation.

1. Turn off the engine, gently push the card into the slot until it locks into place.(Please using class 10 or above high-speed U3 micro-SD card)
2. Find a suitable place on windshield where don’ t obstruct the driver’ s field of vision and remove any foreign matter and clean and dry the windshield beforeinstallation.Tear off the protective layer of the electrostatic sticker and adhere the electrostatic sticker to the windshield to prevent mark/glue on your windshield after removing it
3. Peel off the protective film from the double-sided tape and attach the front camera to the electrostatic sticker Adjust the angle orthe lens by rotating the body of the front cameral
4. Peel off the protective film from the double-sided tape and attach the rear camera to the rear windshield. Adjust the angle of the lens by rotating the body of the rear camera, connect the front cameraand the rear camera
5. Use the pry tool to lift the edges of the rubber window sealing and molding and tuck in the rear camera connection cable.
6. Plugthe cigarette lighter power cable into the cigarette lighter socket and the front camera. Use the pry tool to lift the edges of the windshield trim/molding and tuck in the power cord.
7. Turn on the engine. The dashcam will power up and start recording. Video files are stored on the microSD card Turn off the engine. The dashcam will automatically stop recording and power down

Calibrate Date/Time

AZDOME M300s is built-in GPS, need to set Time zone firestink APP so that the video date/time stamp will be correct

|
---|---
https://itunes.apple.com/us/app/azdome/id1449342214?mt=8| https://play.google.com/store/apps/details?id=cn.com.blackview.azdome

Note

The cellular data maybe cause the live video not to be viewed If the APP won’t show the live video, please disable the
“AZDOME” cellular data of your cellphone. Sure that the Local Network of the “AZDOME” is turned on.

• For Latest iOS System: Setting → AZDOME →Click “Wireless Data “→Select “WLAN”
• Fooleries System: Setting→AZDOME→Disable the “Cellular Data””

WiFi Dashcam is Not cloud dash cam, which all dash cams workalike this, you can’t view your videos remotely away from more than 10 FT from your car. To utilize the WiFi feature, you will need to stay within the 10FT range from your Dash Cam Like your home WIFI, you don’t get a WiFi signal outside your home, the same way the Wifi range for this tiny device s 10FT/3m The AZDOME is available for devices running Android 5.0 and higher, or i0S9.0and higher.

Format Micro-SD Card
There are two ways to format Micro-SD card

a. Press and hold WiFi button for 10 secondsto format and default settings, youwill hear sound “di” when format successfully.
b. Please connect to AZDOME APP, using the function menu named “Format” todo,

General Setting

Photo Size— 12M/ 10M(Default)/ 8M/ 5M/ 3M/ VGA
Here you can choose your desired photo resolution. Higher the resolution better the pixel resolution for captured image.

Video Resolution
Allow to choose the desired video resolution and fpsfframes per second). Higher resolution and fps videos result in smoother videos, but also take more storage space.

• 3840×2160 25P+1920×1080 25(Default)
• 2560×1440 30p+1920×1080 30
• 1920×1080 30p+1920×1080 30

Loop Record — 1min/ 3mins(Default)/ 5mins/Off Allow the dash-cam to continuously record. Please notice: the dash-cam will keep deleting the oldest files automatically when memory card gets full so that it cankeep recording over and over.
Horseleeches length of video file for the loop recording

WDR — On(Default)/Off
Wide Dynamic Range (WDR) improves the exposure by taking the combinations of over exposed and under exposed image into one robust wide range of lighting with higher depth image.

Audio Recording — On(Default)/Off
AZDOME has built-in microphone to record audio with video You can choose to record mute video by choosing OFF.

G-Sensor — Off/ High/ Medium(Default)/ Off
H-Sensor is a 3-axisimpact gravitational accelerometer which is designed to detect physical and gravitational forces on the camera While Video is Being Recorded: In the evenwhen G-Sensorics triggered due to physical or gravitational impact force on the camera, the current loop cycle length of video file will be locked so it will NOT be deleted by loop cycle function

Picture in Picture

• Front Camera: APP ONLY show the front camera image
• Rear Camera: APP ONLY show the rear camera image
• Front(Big)+Rear(Small): The front carbamates the primary image, rear camera is the secondary image
• Front(Small}+Rear(Big): The front camera image is the secondary image, rear camera s the primary image

Parking Monitor

This function menu will be shown when connected to 3-lead hard-wire kit.
-Off: The dashcam will also power off when the car power off ~Time-Lapse Parking Mode:The function is Time-lapse Parking Monitor(1 seconds 1 frame per second), if ON Weyburn OFF the car’ s engine and turn the key to the lock position. Then the camera will STOP the loop recording and it will go into the Time-lapse Parking Monitor recording mode automatically While this Time-lapse Parking Monitor is being recorded, If someone hits your car, then the camera will lock the Time-lapse Parking Monitor recording files, then saved in EMR folder of Micro SD card > then go on Time- lapse Parking Monitor recording.
Now when you start your car for the nettime, the camera will automatically STOP the Time-Lapse Parking Mode. Then it will go into normal video mode automatically to start the continuous video recording.
Note: when playback the Time-Lapse Parking Mode video files plays at faster speed -Impact Detection Parking Mode: If set ON, when you turn OFF theca’ engine and turn the key to the lock position, the dashcam will also power off, but if someone hits your car, the dashcam will turn on to recording for I minutes and saved in EMG folder of Micro SD card, then dash cam power off.

Speed Unit —KM/H(Default)/MPH
You can choose desired speed option stamp to be displayed and
recorded on video stamp based on your selection.

Volume – Low/Medium (Default)/High/Off
This feature allows you to set the volume level for the boot sound volume, prompt volume through camera’ s internal built-in speaker.

Boot Sound
This feature allows you to turn ON/OFF camera button’ s beep sound.
Frequency — 50HZ/ 60HZ(Default)
Hereyoushould choose the frequency accordingly to your power supply specification used in your country based on your geographical location.
Mirror Rear Camera
This feature works only on the rear camera image.
On: Theimage of the rear camera is as same as in the rear mirror, what’ son the left in reality->it’ s on the right of the dash cam screen;
Off: The rear camera image is as same as what you see, what’ son the left in reality- it’ s on the left of the dash cam screen.
Vertical Flip Rear Camera
This feature will allow you to flip your video 180 degree so you cans still have a correct side of image when the cameras mounted upside-down
GPS Information
APP will show the status of longitude, latitude, live speed, satellite number.
Plate Number
This feature will allow you to insert custom vehicle ID or Driver D to be stamped on video
Remaining Time of Recording
This feature will allow you to check the remaining time recording of inserted memory card into the dash cam.
Video Stamps
This feature menu allows
you to choose your choice of stamps
for the bottom of the video. By default they are aloo ON
Time zone Setting
GPTimer Zones GMT/UTC+9
Date/Time
It will Synchronize the phone system date/time
Free Space
Free Space in the Micro-SD card.
Formats Card
This feature will allow you to format inserted memory card, all the data will be deleted
WIFI Name
Here you can change the WiFi Name in APP, the dashcam’ s default SSID: M300S-**
M300Sis built in 2.4G and 5GHz Dual-frequency WiFi module, the default values 5G Oxymorphone can’ t search M300S WiFi, it mesa your phone ONLY support 2.4GHZ band, Short Press 3 times WiFi button in arow toshiftto2.4GHZ

WIFI Password
Here you can change the Wii Password in APP, the default password: 12345678
Default Settings
Here you can restore all the settings to factory default settings.
Firmware Version
Here you can check the current firmware version installed on your camera. You will need this information in the future to check if newer version of firmware is available.

Playing and Managing Videos

Managing videos in Wi-Fi

1. Search forte AZDOME app in the Google Play Store or Apple App Store and install it on your smartphone
2. Pair” your smartphone with the AZDOME dash cam via Wi-Fi Direct:
   a. Power on the engineer the dash camwill power on and Wifi will ON automatically.Choose your AZDOME dashcam from the phone WiFi network list. The dashcam’ s default SSID begins withits model number (e.g. M300S-**, password 12345678)
   b. Go to dash cam preview interface. Press the “Device Album” to get Photo, Video, Emergency files
   c. You also can select files to download into your smartphone, please find these downloaded files in APP original interface menu named “Local Video”
   d. You can playback the video or edit the video files.

Managing videos by Micro-SD card reader

1. Please remove the Micro SD card from camera and insert it directly in your laptop if you have a Micro SD Card slot (otherwise please using a MicroSD Card reader)
2. you should be able to see drive D” or “E” or other name depending on the pre-installed hard drives.Onceyou find the added flash drive, double click init, then you will see the file folders- Movie / EMR/ Photo
   Movie: The loop recording video files that can be overwritten. EMR:Thevideo file will be locked so it will NOT be deleted byoop recording
   function Photo:The photos Then simply double click on the video to play themFilename A=Front dash FCAMvideo
   file Filename B=Rear camera video

AZDOME GPS Player

1. Please got our official website www.azdomes.com/pages/support to download the AZDOME Player(For Windows or macOS)
2. Install the AZDOME Player in your computer. (Note: Paes close or ignore the prompt of the anti-virus software, we confirm thatitwill not bring any security impact to your computer.)
3. Take off the memory card from the dashcam and insertitto your compute
4. There are two ways to play video A, Click File-Open icon to choose the folder which you want to play, click to start play. (Note that you can ONLY select one folder to playland see no video files) B, Seclect from “My Computer” and find the memory card disk, choose the video file you want to play, you can drag and drop the file directly to the player. You can get the GPS information onthe player. Customer Service Center service@azdome.hk

Update Firmware

If you get stuck with any settings and want to update to the latest firmware

1. Please download the firmware file in azdome.hk/downloads.html->

2. Copy the firmware
   file named “FW96670.bin” to Micro SD card andinsert Micro-SD card to dash cam;

3. Connect to power,
   then the red light will be flash rapidly, it will take 30-40 seconds to update. The dash cam will power on automatically and says “WiFiis ON” when update successfully.

4. Press and hold WiFi button for 10 seconds to format the Micro SD Card in dash cam, otherwise the dash-cam will update again when next power on.

Rear Camera
Disconneted| Rear camera connected to dashcam faild
---|---
Memory Card is Full| Too much video files to delete
Two point four G WiFi| 2.4GHZ WiFi Mode
Five G WiFi| 5GHZ WiFi Mode

FAQ

Q:lcan’ tget live video on AZDOME APP, what should | do ?

If can’ t get live-video on APP, please turn off cellular data of AZDOME APP, take iPhone and Google phone(Android 12) for example. Technical Service : service@azdome. hk M300S is builtin 2.4G and 5GHz Dual-frequency WiFi module, the defaultvalue s 56 Ifyour phone can’ t search M300S WiFi, it measyour phone ONLY support 24GHZ band, please Short Press WiFi button for 3 times in a row to shift to 2.4GHZ.

Notice

****This product complieswith the radio interface requireme- nts of the European Community.
This symbol means the product must not be discarded as Household waste, and should be delivered to an appropriate and recycling  helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contactyourlocal municipality, disposal service, or the shop where you bought this product.
Changes or modifications notexpressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference n a residential
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, therein
guarantee that interference will not occur in a particular installation.
Ifthis equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipmentoff on, the users encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that ophichthid receiver is connected
• Consult the dealer or an experienced radio/TV technician for help.

This device complies with Part 15 of the FCC Rules
Operation s subject to the following two conditions: 1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated withe minimum distance of 20cm between the radiator & your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.

Dong Guan Kaka Electronic Technology Co, Ltd.
www.azdomes.com service@azdome.hk
Address : Room 102, Building 1, No.1 Long cheng Street, Qingxi Town,
Dongguan, Guangdong, 523660, CN V20220818

Documents / Resources

| AZDOME M300S 64GB Memory card included Car Dashcam [pdf] User Manual
M300S 64GB Memory card included Car Dashcam, M300S, 64GB Memory card included Car Dashcam, card included Car Dashcam, included Car Dashcam, Car Dashcam
---|---

References

• Best Dash Cam For Car | Wireless Dash Cam – AZDOME Official Stores

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>