MAXIM 21282 Light Vanity User Manual

MAXIM 21282 Light Vanity

Product Information

Specifications

• Model Number: 21280, 21281, 21282
• Fixture Type: 2 Light Vanity
• Mounting Bracket: Included
• Outlet Box Screw: 2 pcs
• Cap Nut: 2 pcs
• Support Screw: 2 pcs
• Green Ground Screw: 1 pc
• Socket Ring: 2 pcs
• Hex Nut: 2 pcs
• Wire Connector: 3 pcs

Product Usage Instructions

Preparation

1. Ensure you have all the necessary parts: mounting bracket, outlet box screw, cap nut, support screw, green ground screw, socket ring, hex nut, and wire connector.

Installation

Preparing the Mounting Bracket

1. Attach the mounting bracket (H1) to the fixture body.

Installing the Mounting Bracket

1. Secure the mounting bracket to the desired location using the outlet box screw (H4) and cap nut (H7).

Making the Electrical Connections

1. Connect the wires from the fixture to the wires in the outlet box using the wire connectors (H6).
2. Ensure all wires are properly connected and positioned inside the outlet box.

Installing the Fixture Body to the Outlet Box

1. Choose the desired orientation of the fixture (facing up or facing down).
2. Attach the fixture body to the outlet box using the support screw (H2) and cap nut (H7).

Assembling the Glass Shades

1. Follow the instructions provided to assemble the glass shades.

Installing the Light Bulbs

1. Recommended bulb type: ST64 bulbs.
2. Alternatively, you can use two MAX 60 W medium base (E26) type A bulbs or MAX 9W medium base (E26) self-ballasted LED bulbs.
3. Do not exceed the recommended wattage.

Cleaning

Refer to the cleaning instructions provided in the user manual for proper cleaning and maintenance of the product.

Troubleshooting

If you encounter any issues with the product, please refer to the troubleshooting section in the user manual for guidance.

FAQ

Q: Can I install the fixture facing up or facing down?

A: Yes, you can choose the desired orientation of the fixture during installation.

Q: What type of bulbs should I use?

A: The recommended bulb type is ST64 bulbs. Alternatively, you can use two MAX 60 W medium base (E26) type A bulbs or MAX 9W medium base (E26) self-ballasted LED bulbs. Do not exceed the recommended wattage.

2 LIGHT VANITY
Model number: 21280, 21281, 21282

Hardware

(Parts are not to scale)

THIS MANUAL CONTAINS IMPORTANT SAFETY INFORMATION. PLEASE READ AND KEEP FOR FUTURE REFERENCE.

IMPORTANT SAFETY INFORMATION

• Please read and understand this entire manual before attempting to assemble, operate or install the product.
• Turn off electricity at main fuse box (or circuit breaker box) before beginning installation by removing fuse (or switching off circuit breaker).
• Be careful not to damage or cut the wire insulation (covering) during fixture installation. Do not permit wires to contact any surface having a sharp edge. To do so may damage or cut the wire insulation, which could cause serious injury or death from electric shock.
• All electrical connections must be in agreement with local codes, ordinances or the national electric code (NEC). Contact your municipal building department to learn about your local codes, permits and/or inspections. If you do not have electrical wiring experience, refer to a do-it-yourself wiring handbook or have your fixture installed by a qualified licensed electrician.
• Risk of fire – most dwellings built before 1985 have supply wire rated for 140°F/60ºC. Consult a qualified electrician before installation.
• Do not exceed the recommended wattage. Refer to the re-lamping label on the light socket for maximum wattage.
• Do not replace a bulb when electrical outlet switch is turned to the “ON” position.
• Do not immerse your lamp in water; doing so will damage the wire.
• Keep materials that burn easily away from lighted bulbs.

PREPARATION

• Before beginning assembly, installation or operation of product, make sure all parts are present. Compare parts with package contents list and diagram on previous page. If any part is missing or damaged, do not attempt to assemble, install or operate the product. Contact customer service for replacement parts.
• Tools required for assembly (not included): flathead screwdriver, phillips screwdriver, pliers, electrical tape, wire cutters, safety glasses, ladder, wire stripper.

INSTALLATION

1. Preparing the mounting bracket

   • Unscrew the two cap nuts (H7) from the support screws (long) (H2). Remove the mounting bracket (H1) from the fixture body (A), and keep the cap nuts (H7) for later use.
   • Loosen the hex nuts (H3) on the support screws (long) (H2) and adjust the support screws (long)(H2) so that they extend long enough to protrude through the canopy of the fixture body (A). Then secure the support screws (long) (H2) in place using the hex nuts (H3).

2. Installing the mounting bracket
   Fasten the mounting bracket (H1) onto the outlet box (not provided) using two outlet box screws (short) (H4).

3. Making the electrical connections

   • Strip 3/4 in. of insulation from the wire ends.
   • Connect the black wire from the fixture to the black wire from the outlet box, then connect the white wire from the fixture to the white wire from the outlet box.
   • Connect the bare copper ground wire to the ground wire from the outlet box. The bare copper ground wire from the fixture must loop one turn under the head of the green ground screw (H5) on the mounting bracket (H1) before
   • it is connected to the ground conductor of the supply circuit. Cover the wires with wire connectors (H6). Tape the wire connectors (H6) and wires together, and carefully position all wires inside the outlet box.

4. Installing the fixture body to the outlet box
   • Place the fixture body (A) over the outlet box, and ensure the heads of the support screws (long) (H2) come through the holes of back of the fixture body (A).
   • Tighten the cap nuts (H7) onto the protruding support screws (long) (H2) on the mounting bracket (H1) until the fixture body (A) is held firmly against the wall.
     Note: The whole fixture can be installed facing up or facing down.

5. Assembling the glass shades
   Unscrew the socket rings (H8) from the sockets on the fixture body (A). Set the glass shades (B) onto each socket, and secure them with the socket rings (H8).

6. Installing the light bulbs

   • Install the light bulbs (not provided) into the sockets. Use two MAX 60 W medium base (E26) type “ST64” bulbs (recommended).
     Note: You can also use two MAX 60 W medium base (E26) type “A” bulbs or MAX 9W medium base (E26) self-ballasted LED bulbs. Do not exceed the recommended wattage.

CLEANING

• Do not use any cleaners with chemicals, solvents, or harsh abrasives. Use only a dry, soft cloth to dust or wipe carefully.
• To clean the fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box. Use a dry or slightly dampened, clean cloth to wipe the exterior surface of the fixture.

TROUBLESHOOTING

• The light does not come on at all:
  • a) Check whether the bulbs were burned out.
  • b) Make sure the wall switch and circuit breaker are on.
  • c) Make sure the wiring is correct.
  • d) Make sure the circuit breaker is set in the “ON” position.
• Fuse blows or circuit trips when light is turned on.
  • a) Check for crossed wires, ensure wiring is correct.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>