SBOX PLB-133L Fixed Wall Mount Instruction Manual
- June 4, 2024
- SBOX
Table of Contents
SBOX PLB-133L Fixed Wall Mount
UNPACKING INSTRUCTIONS
- Carefully open the carton, remove the contents, and layout on cardboard or another protective surface to avoid damage.
- Check package contents against the Supplied Parts List in the next page to assure that all components were received undamaged. Do not use damaged or defective parts.
- Carefully read all instructions before attempting installation.
IMPORTANT SAFETY INFORMATION
Install and operate this device with care. Please read this instruction before
beginning the installation, and carefully follow all instructions contained
herein. Use proper safety equipment during installation.
Please call a qualified installation contractor for help if you:
- If you don’t understand these directions or have any doubts about the safety of the installation.
- If you are uncertain about the nature of your wall, consult a qualified installation contractor.
Do not use this product for any purpose or in any configuration not explicitly specified in this instruction. We hereby disclaim any and all liability for injury or damage arising from incorrect assembly, incorrect mounting, or incorrect use of this product.
CAUTION!
This TV mount must be securely attached to the vertical wall. If the mount is not properly installed it may fall, resulting in possible injury and/or damage.
Tools Required
- 5/32″(4mm) Drill Bit
- Phillips Screwdriver
- 3/8″(10mm) Masonry Bit
- Stud Finder
- Wrench or Socket Set
- Carpenter’s Level
Note: The mounting components and hardware supplied in this package are not designed for installations to walls with steel studs or to cinder block walls. If the hardware you need for your installation is not included, please consult your local hardware store for proper mounting hardware for the application.
Supplied Parts List
Step 1 Mounting the Monitor Brackets to a TV with Flat Back
First of all, make sure the diameter of the Bolt(d,e,f,g) your TV requires. Once you have determined the correct diameter, please see the relative diagram as below. You will thread the Bolt into the TV using the correct Lock Washer(l,m,n,o) and Washer(r,s). Please make sure the Monitor Brackets(b,c) are vertically centered and level with each other.
Step 2 Mounting the Wall Plate to the Wall
Brick, Solid Concrete and Concrete Block mounting:
Use the Wall Plate(a) as a template to mark 3 hole locations on the wall. Make
sure these holes are level. Pre-Drill these holes with a 3/8″(10mm) masonry
bit to at least 2.4″(60mm) in depth. Insert a Concrete Anchor(v) into each of
these holes. Make sure the anchor is seated completely flush with the concrete
surface even if there is a layer of drywall or other material in front. Attach
the Wall Plate to the wall using 3pcs Lag Bolts(t) and 3pcs Lag Bolt
Washers(u), shown in Diagram 2A.
Wood Stud mounting:
The Wall Plate(a) must be mounted to two wood studs at least 16″(406mm) apart.
Use a stud finder to locate two adjacent studs. It is a good idea to verify
where the studs are located with an awl or thin nail shown in Diagram 2B. Pre-
drill a 2.4″(60mm) deep hole at the desired height in each stud using a
5/32″(4mm) drill bit. Make sure these holes are in the center area of the
studs and level with each other. Attach the Wall Plate to the wall using the
2pcs Lag Bolts(t) and 2pcs Lag Bolt Washers(u).
Step 3 Attaching Monitor to Wall Plate and Insert Locking Bar
Warning: Some TVs may require two people to lift! We are not responsible for personal injury or product damage. First, hook the Monitor Brackets(b) over the top of the wall Plate(a), then let the bottom of the Monitor Brackets rotate to the wall as shown in Diagram 3A. Finally, insert the locking bar(c) as shown in Diagram 3B.
Thanks for choosing our products, enjoy the use.
https://tm.by
MHTepHeT-Mara3uH TM.by
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>