SBOX BARISTA 3In1 Multi Capsule Coffee Maker Instruction Manual

SBOX BARISTA 3In1 Multi Capsule Coffee Maker

Read this important information carefully before you use the appliance and save it for future reference.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following:

• This appliance is not intended for use by persons (including children) with reduced physical, sensory, or mental capacities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.
• Before plugging the appliance in, make sure that the power it uses corresponds to your electrical supply system and that the outlet is earthed.

ANY ERROR IN THE ELECTRICAL CONNECTION WILL NEGATE YOUR GUARANTEE.

• This appliance is designed for domestic use only. Any commercial use, inappropriate use or failure to comply with the instructions, the manufacturer accepts no responsibility, and the guarantee will not apply.
• Unplug the appliance when you have finished using it and when you clean it.
• Do not use the appliance if it is not working properly or if it has been damaged. If this occurs, contact an authorized service center.
• All interventions other than cleaning and everyday maintenance by the customer must be performed by an authorized service center.
• Do not use the appliance if the power cord or plug is damaged. The power cord must be replaced by an authorized center to prevent any danger.
• Do not immerse the appliance, power cord, or plug in water or any other liquid.
• Do not leave the power cord within reach of children.
• The power cord must never be closed to or in contact with the hot parts of your appliance, near a source of heat or over a sharp edge.
• For the safety, only use the manufacturer’s accessories and spare parts designed for this appliance.
• Do not pull on the cord to unplug the appliance.
• Never put your appliance on a hotplate.
• This appliance is intended to be used only in the household and similar applications such as:
• Staff kitchen areas in shops, offices, and other working environments.
• Farmhouses.
• By clients in hotels, motels, and other residential type environments.
• Bed and breakfast type environments.

SPECIAL INSTRUCTIONS:

• Children shall not play with the appliance.
• This appliance shall not be used by children.
• Keep the appliance and its cord out of reach of children

GENERAL DESCRIPTION

COMPACT DESIGN

Explanation of control panel
Function Buttons:

LED signals
All function buttons illuminated green: When the appliance is ready for operation; press any key for power on.

BEFORE THE FIRST USE

• Take the appliance and accessories out the box. Remove the stickers, protective foil, or plastic from the device.
• Place the device on a flat stable surface and ensure a minimum of 10cm free space around the device. This device is not suitable for installation in a cabinet or for outside use.

CAUTION:

• Improper handling of electrical equipment is dangerous and can be lethal. Please pay attention to the safety precautions in this manual, in particular the following:
  • Danger of scalding beware of hot water in a cabinet or for outside use.

WARNING!

• There is sharp needle upper the capsule adaptor. Do not put your hand or finger close to any part near the needle after the adaptor has been removed.
• Do not operate the machine with an empty water tank or water is less than MINIMUM level.
• Do not open the handle when the machine is brewing.
• Be careful, the adaptor can be very hot after brewing!
• Always pull out the power plug before cleaning the machine.
• Only use the machine in a dry room.
• Thoroughly rinse out the water tank with fresh water before using for the first time. Clean the machine using a damp cloth only.
• Children should be supervised to ensure that they do not play with the appliance.
• WARNING: The capsule holder must not be opened during use.
• The coffeemaker shall not be placed in a cabinet when in use
• The coffeemaker must be operated with the decorative door open or the cabinet door open.
• WARNING: Do not use the appliance if the surface is cracked.
• After the product is used, there is still residual heat on the surface of the heating element. Please cool it before cleaning to prevent burns.

SPECIAL INSTRUCTION

There are two ways to fill the water tank: directly into the machine. by using for example a jug. or by removing the water tank.

1. Filing without removing the tank:
   • Lift the water tank cover.
   • Fill the tank with cold fresh water.
   • The maximum capacity is 0.8 liter.
   • Replace the tank cover.
2. Filing by removing the water tank:
   • Hold the water tank tilted to remove it from the machine.
   • Fill the tank up to Fill the tank up to the “MAX” mark with cold fresh water (the maximum capacity is 0.8 liter).
   • Slide the water tank slowly on water tank base, when the water tank outlet is inserted in the inlet receptacle, push firmly to lock the water tank.

Before using for the first time or after long pauses (e.g., holidays), the machine must be flushed. This short procedure can thoroughly flush and clean the internal pipes.

• Press any function button to power on.
• The light of buttons will become steady on when the machine is heated up.
• Heating up time is approximately 35 seconds.
• Before pressing the button, make sure that:
• The handle is closed without a capsule inside.
• The water tank is full.
• The water tank is firmly in place, otherwise water may leak.
• A large bowl (250ml size or above) is placed under the dispenser.
• Open the handle when the flushing process has finished.
• Empty the bowl.

ADAPTERS:
This machine uses multiple adapters, see below for information:

1. Nespresso Capsules adapter
2. Dolce Gusto capsules adapter
3. Coffee powder adapter

USE

Nespresso® capsule

• Open the handle.
• Pull out the brewing basket for Nespresso® capsules.
• Insert a capsule to the brewing basket.
• Push in the brewing basket with capsule.
• Close the handle.
• Place a cup under the dispenser.
• Press the desired cup size button only once.
• The selected button will blink, and the machine will start brewing. When the brewing process is complete, dispensing will stop automatically when the default brewing volume is reached. This default setting volume can be adjusted to suit personal taste. Raise the handle and pull out the brewing basket to inject the used capsule into the container.
• After pressing the button, the desired button led flash a few seconds first, then the brewing will start. The flash process is for the heating, this is the normal procedure.

DOLCE-GUSTO® CAPSULE

• Open the handle.
• Pull out the brewing basket for Dolce-Gusto® capsules.
• Insert a capsule to the brewing basket.
• Push in the brewing basket with capsule.
• Close the handle.
•  Place a cup under the dispenser.
• Press the desired cup size button only once.
• The selected button will blink, and the machine will start brewing. When the brewing process is complete, dispensing will stop automatically when the default brewing volume is reached. This default setting volume can be adjusted to suit personal taste. Raise the handle and pull out the brewing basket to inject the used capsule into the container.
• After pressing the button, the desired button led flash a few seconds first, then the brewing will start. The flash process is for the heating, this is the normal procedure.

COFFEE POWDER

• Open the handle.
• Pull out the brewing basket for coffee power.
• Place the coffee powder adapter into the brewing basket.
• Put the coffee powder into the adapter and push firmly.
• Push the brewing basket into the machine.
• Close the handle.
• Place a cup under the dispenser.
• Press the desired cup size button only once.
• The desired coffee button only once. the brewing process is complete, dispensing will stop automatically when the default brewing time is reaches. This default setting time can be adjusted to suit personal taste.
• Raise the handle and pull out the brewing basket to inject the used coffee powder into the container.
• After pressing the button, the desired button led flash a few seconds first. then the brewing will start. The flash process is for heating, this is the normal procedure.

AUTOMATICALLY POWER-OFF FUNCTION

• The machine will automatically power off and go into energy saving mode when there is no operation within 9 minutes. Press any function button to activate the machine again.
• Coffee volume setting
• The amount of coffee can be changed by adjusting the default brewing time to suit personal taste.

PROGRAM-SUIT PERSONAL TASTE
Each coffee button can be programmed with a coffee volume for an individual cup size. The procedure for programming is the same for both coffee buttons.

Programmable volume range ………………………… 25 – 200 ml

1. Prepare coffee as usual (see user manual) but keep the coffee button pressed for at least 3 seconds to start programming mode.
2. Only release the button when the desired fill level is reached.

RESTORE THE ORIGINAL FACTORY DEFAULT COFFEE CUP VOLUME SETTING

• Press all 3 buttons at the same time for 5 seconds in Ready State,2 beeps.
• All the green led light flash for 5 seconds and back to the process “First use”. the” First use” Mode will see the red-light flashing, so please keep the water tank not empty.
• Take out the capsule / ground coffee in brewing adapter.
• Put back the brewing adapter into the machine.
• Press the red-light button, the machine will fill up water.
• Let water come out until the red light (flashing) turn to green light (flashing).
• Machine will pre-heat around 35 seconds, the green light stop flashing, machine ready to brew again.

DESCALING PROCEDURE

If all the button flash in red and green alternatively during the normal use, that’s mean the machine needs to be descaling (see below picture).

DESCALING PREPARATION:

• Eject capsule or ground coffee from the adapter, re-insert the adapter into machine (please only insert the Nespresso adapter or the Ground coffee adapter for this process, other adapter is not suitable).
• Remove and empty the water tank.
• Place a container under the outlet (volume size: larger than 1-liter).
• Fill the water tank with the descaler solution, obtained by diluting the descaler provided with water (fill the water tank up to the MAX line), re-insert the water tank to machine.
• Plug-in the power cord of machine, press the small cup button and medium cup button at the same time for 5 seconds, small cup button lights on in green, large cup button flash in red and green alternatively, the machine is in descaling mode now (see below picture).
• Press these two keys at the same time for 5 seconds
• Large cup button flash in green/ red alternatively

1 ST DESCALING PHASE:

• Step6: Press the small cup button, the small cup button green light off, large cup button keep flash in green/red alternatively.
• Step 7: At the same time, the machine start pumping some amount of water and stopped automatically, after waiting 2.5 minutes, the machine will pump and wait again, totally repeat 8 times.
• Step8: After 8 times pump and wait, machine will keep pumping water until water tank is empty, 1st descaling phase finished. Large cup button keep flash in green/red alternatively.

2ND DESCALING PHASE:

• Step9: Remove and clean the water tank, fill with fresh water up to the MAX line again, re-insert to the machine.
• Step10: Remove and clean the brew adapter, re-insert to the machine.
• Step11: At this moment, the medium cup button lights on in green, large cup button flash in red and green alternatively (flashing faster than the 1st phase), the machine is into the 2nd phase.
• Step9: Remove and clean the water tank, fill with fresh water up to the MAX line again, re-insert to the machine.
• Step10: Remove and clean the brew adapter, re-insert to the machine.
• Step11: At this moment, the medium cup button lights on in green, large cup button flash in red and green alternatively (flashing faster than the 1st phase), the machine is into the 2nd phase.

POWER OFF SETTING

Press Small Cup button + Large Cup button at the same time, then the machine will power off.

FACTORY DEFAULT SETTING
Totally reset of the machine:

• Step1 : Switch OFF machine (plug out) and open handle
• Step 2: Press and Hold Small cup and medium cup buttons
• Step 3: Switch on (plug in), Beep once
• Step 4: Release the buttons
• Step 5: Close the handle, Beep twice
• Step 6: Press Small cup medium cup +Large Cup these three buttons, long “Beep”
• Step 7: To quit switch OFF machine (plug out)
• Step 8: Turn on the machine (plug in); press any button, start from First use procedure.

“First Use” Mode to normal work

• The” First use” Mode will see the red-light flashing, so please keep the water tank not empty.
• Take out the capsule / ground coffee in brewing adapter.
• Put back the brewing adapter into the machine.
• Press the red-light button, the machine will fill up water.
• Let water come out until the red light (flashing) turn to green light (flashing).
• Machine will pre-heat around 35 seconds, the green light stop flashing, machine ready to brew again.

TROUBLESHOOTING

• Scale build-up in machine.
• Cold machine.

|

• Descale.
• Brewing a cup of water to warm up the circuit.

Water on table|

• Water tank is leaking.
• Drip tray full of water.

|

• Check if the valve on water tank is stuck.
• Empty the drip tray.

Handle cannot close| -The brewing basket is not placed well.| -Push the brewing basket into correct position.
**RED light flashing|

1. If the water tank empty.
2. If the machine lacks water
3. After the machine factory default setting

|

• Solve the red-light flashing
• Step1 : Fill up the water tank.
• Step2: Take out the capsule / ground coffee in brewing adapter.
• Step3: Put back the brewing adapter into the machine.
• Step4: Press the red-light button, the machine will fill up water.
• Step5 : Let water come out until the red light (flashing) turn to green light (flashing).
• Step6: Machine will pre-heat around 35 seconds, the green light stop flashing, machine ready to brew again.

SPECIFICATIONS

• Rated voltage 220-240V
• Rated power 1150-1350W
• Water Tank Capacity 800ml
• Programmable Cup Size 50ml / 100ml 1150ml
• Auto Shut Off 9 minutes

ENVIRONMENT FRIENDLY DISPOSAL
Do not throw away the appliance with the normal household waste at the end of its life, but hand it in at an official collection point for recycling. By doing this, you help to preserve the environment.
This Coffee machine are intended for household use only

WARRANTY CARD

• ITEM_____
• MODEL:___
• RECEIPT NO.___
• DATE OF PURCHASE:_____
• SELLING SPOT (COMPANY):____
• THE CUSTOMER: ___

WARRANTY PERIOD (MONTHS): 36

SIGNATURE__
STAMP:

All SBOX products are examined and tested after each stage of the production process and have all the required certificates (EMC, CE … ). The products are subject to the following warranty conditions:

• The warranty period for SBOX products is 36 months (on batteries 6 months) and begins on the day of being sold in the store
• The warranty can only be claimed upon presentation of the original purchase invoice and a filed warranty paper with a stamp from the store it was bought at, and if the product has original packaging and all components and equipment
• All malfunctioning of the product resulting from factory defects, that occur during the warranty period, and in the normal use of the product in compliance with all instructions will be removed. This warranty covers only defects in material and production.
• If the product malfunctions during the warranty period, your SBOX distributor will give you the product (after which is checked by a professional) repaired or replaced• If the repair at the authorized service center is not completed within 30 days of being received at the service center, we will replace the product with a new one. If the repair during the warranty period lasts longer than 15 days, the warranty period is extended by as many days as the repair lasted.
• If the device needs to be repaired within the warranty period, contact the store where you bought the product. If the product has to be sent to an authorized service center or general distributor, please send the product (with all parts and accessories) in the original packaging and with all the necessary documents (invoice, warranty card, etc.). The product can be repaired only in the authorized service center of the importer. The costs of shipping the product to the service center are funded by the customer. Possible damage to the product that can occur during transport is at the expense and risk of the buyer Sending the product from the service center to the customer is funded by the service technician/the importer

This warranty does NOT cover:

• Damage or malfunctions that would occur as a result of incorrect connection, incorrect polarization. incorrect battery placement, etc.
• Defects caused by improper handling of products, use of parts or equipment that is not prescribed by our specifications, unauthorized product modification, and defects mechanical damage to the product
• Defects that can occur due to product fall, use of force, natural disasters (flood, fire, thunder, earthquake … ), due to battery leakage, due to unstable 220V voltage, frequent variations and/or power outages, etc.
• Damage caused during transport to the customer
• Products  have been opened or repaired by an unauthorized person
• Parts that are considered consumables such as batteries, etc.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>