Angelcare AC017 Movement Monitor Owner’s Manual

Angelcare AC017 Movement Monitor

Product Information

Model: AC017 Movement Monitor
The AC017 Movement Monitor is a device designed to aid in the monitoring of your baby. It includes a sensor pad that detects movement and alerts you if no movement is detected for a certain Bperiod of time. This product is not intended to replace responsible adult supervision and should not be used as a medical device or to prevent Sudden Infant Death Syndrome (SIDS).

Warnings

• This product cannot replace responsible adult supervision. Always provide the necessary supervision for the safety of your baby.
• Immediately check on the baby whenever an alarm sounds.
• Do not use the monitor near the water.
• Keep the monitor away from heat sources.
• Place the Nursery Unit on a flat surface with proper ventilation.
• This product is not a toy. Do not allow children to play with it.
• Adult assembly is required. Exercise care when unpacking and assembling the product.

Battery Warning
Follow the manufacturer’s instructions for battery usage and replacement. Improper handling of batteries may cause them to leak or explode, resulting in injury or damage. Dispose of used batteries according to local regulations.

Important Safety Instructions

1. Water and moisture – Do not use this apparatus near water or in wet environments. Take precautions to prevent objects from falling onto the units and liquids from spilling into them.
2. Cleaning – Disconnect all units before cleaning. Do not immerse any part of the monitor in water. Clean only with a dry cloth. Ventilation – Do not block any ventilation openings. Allow for proper ventilation when using the units. Do not cover the Nursery Unit with any object that may interfere with airflow.
3. Heat sources – Do not install the monitor near heat sources that can damage the device.
4. Accessories – Only use attachments and accessories specified by the manufacturer. Follow the recommended mounting instructions to prevent injury or damage.

Product Usage Instructions

Assembly
Follow these steps to assemble the AC017 Movement Monitor:

1. Unpack all components from the packaging.
2. Ensure you have all the necessary parts mentioned in the manual.
3. Follow the assembly instructions provided in the manual to connect and secure the components.

Placing the Sensor Pad
The sensor pad should be placed under the baby’s mattress, ensuring it is positioned in the center of the crib or cot. Make sure the sensor pad is securely connected to the Nursery Unit.

Setting Up the Nursery Unit
Place the Nursery Unit on a flat surface in an upright position. Ensure there is proper ventilation around the unit. Do not place it on sofas, cushions, beds, or any other surface that may block ventilation.

Connecting and Powering On
Connect the Nursery Unit to a power source using the provided power adapter. Once connected, press the power button to turn on the monitor.

Adjusting Sensitivity
The AC017 Movement Monitor allows you to adjust the sensitivity of the sensor pad. Refer to the manual for instructions on how to adjust the sensitivity level based on your baby’s needs.

Monitoring and Alarms
Once the monitor is set up and powered on, it will start monitoring your baby’s movements. If no movement is detected for a certain period of time, the monitor will sound an alarm to alert you. Always check on your baby immediately when an alarm sounds.

Cleaning and Maintenance
To clean the monitor, disconnect all units and use a dry cloth to wipe the surfaces. Do not immerse any part of the monitor in water. Regularly check the sensor pad and cables for any signs of damage or wear and tear. Replace any damaged components following the manufacturer’s instructions.

Specifications

• Model: AC017
• Product Type: Movement Monitor
• Age Range: Suitable for infants up to 24 months
• Power Source: AC adapter
• Sensor Pad Dimensions: [Dimensions]
• Nursery Unit Dimensions: [Dimensions]
• Weight: [Weight]
• Manufacturer: [Manufacturer]

FAQ

Q: Can the AC017 Movement Monitor prevent Sudden Infant Death Syndrome (SIDS)?
A: No, the AC017 Movement Monitor is not designed to prevent SIDS. It is intended to aid in monitoring your baby’s movements and alert you if no movement is detected for a certain period of time. Always follow safe sleep practices and consult with healthcare professionals for SIDS prevention guidelines.

Q: Can I use the sensor pad with older children or adults?
A: No, the sensor pad feature is not intended for use with adults, children, or infants older than 24 months. It is specifically designed for monitoring the movements of infants within the specified age range.

Q: What should I do if the monitor’s alarm sounds?
A: Immediately check on your baby when the monitor’s alarm sounds. Ensure their safety and address any potential issues. If the alarm persists or there are any concerns, consult with a healthcare professional.

For assistance, FAQs or guidance with your monitor please visit our Customer Support page at angelcare.co.uk

OWNER’S MANUAL
KEEP YOUR OWNER’S MANUAL FOR FUTURE REFERENCE. PLEASE READ THE WARNINGS AND INSTRUCTIONS CAREFULLY BEFORE ASSEMBLING & USING THE PRODUCT. FAILURE TO FOLLOW THE WARNINGS AND THE INSTRUCTIONS COULD RESULT IN SERIOUS INJURY OR DEATH OR DAMAGE TO THE PRODUCT. THE SENSOR PAD FEATURE IS NOT FOR USE WITH ADULTS, CHILDREN OR INFANTS OLDER THAN 24 MONTHS. THE SENSOR PAD IS NOT INTENDED TO BE USED TO DETERMINE IF BABY IS OUT OF THE COT.

WARNING
Adult assembly is required. Keep small parts away from children when assembling. We, at Angelcare, stand behind all of our products. If you are not completely satisfied or have any questions, in United States and Canada: Please contact us at: angelcare@cdecinc.ca Other countries: Please contact your local distributor.

1. THIS PRODUCT CANNOT REPLACE RESPONSIBLE ADULT SUPERVISION. This product is designed to aid in the monitoring of your baby. When using the monitor, you must still provide the supervision necessary for the continued safety of your baby. Monitoring of premature babies, or those considered to be at risk, should always be carried out under the supervision of a health professional. This monitor SHOULD NOT be used as a medical device, nor as a device to prevent Sudden Infant Death Syndrome (SIDS).

2. ALWAYS be sure to immediately check on baby whenever an alarm sounds.

3. DO NOT use monitor near water (such as bath tub, sink, etc.).
   CAUTION
   RISK OF ELECTRIC SHOCK DO NOT OPEN DO NOT EXPOSE TO RAIN OR MOISTURE

4. Keep monitor AWAY from heat sources (such as stoves, radiators, etc.).

5. ALWAYS place the Nursery Unit on a flat surface in an upright position and allow for proper ventilation. DO NOT place on sofas, cushions, beds, etc. which may block ventilation.

6. This product is NOT a toy. DO NOT allow children to play with it.

7. This product contains small parts. Adult assembly required. Exercise care when unpacking and assembling the product and keep small parts away from children.

8. When using the monitor, the room temperature should be between 10°C and 40°C.
   BATTERY WARNING

9. The Wireless Sensor Pad battery is a replaceable Button Cell Lithium battery. Only use the Angelcare® recommended replacement battery. Danger of explosion if the wrong battery is used or if replaced incorrectly. Refer to your user manual for correct battery installation. DO NOT short circuit supply terminals. Remove the batteries from your Nursery Unit and Sensor Pad if product is to be stored for an extended period of time. Dispose of batteries according to your local ordinances. The Button cell battery represents a small part and a choking hazard. ALWAYS keep all batteries away from children.

**IMPORTANT SAFETY INSTRUCTIONS

**

1. Heed all warnings – All warnings on the product and in the operating instructions should be adhered to.
2. Follow all instructions – All operating and use instructions should be followed.
3. Water and moisture – DO NOT use this apparatus near water. For example, near a bath tub, wash bowl, kitchen sink, laundry tub, in a wet environment or near a swimming pool and the like. Care should be taken so that objects DO NOT fall onto units and that liquids are not spilled into either unit or Sensor Pad through its openings.
4. Cleaning – Disconnect all units before cleaning. DO NOT immerse in water any part of the monitor. Clean only with dry cloth.
5. Ventilation – DO NOT block any ventilation openings. Allow for proper ventilation when units are in use. DO NOT cover the Nursery Unit with any object such as a blanket. DO NOT place it in a drawer or in any location which would muffle the sound or interfere with the normal flow of air.
6. Heat sources – DO NOT install near any heat sources such as radiators, heat registers, stoves, TVs or other apparatus (including amplifiers) that produce heat. Heat can damage the case or electrical parts.
7. Accessories – Only use attachments accessories specified by the manufacturer. DO NOT place this product on an unstable cart, stand, tripod, bracket or table. The product may fall, causing serious injury to a child or adult and serious damage to the product. Use ONLY with a cart, stand, tripod, bracket or table recommended by the manufacturer or sold with the product. Any mounting of the product should follow the manufacturer’s instructions.
8. Servicing – DO NOT attempt to service this product yourself as opening or removing covers (except battery door) may expose you to dangerous voltage or other hazards.
9. Replacement parts – When replacement parts are required, be sure the replacement parts specified by the manufacturer have the same characteristic as the original part. Unauthorized substitution may result in fire, electric shock or other hazards.
10. Usage – This baby monitor is intended as an aid. It is NOT a substitute for responsible and proper adult supervision and should not be used as such. Use this appliance ONLY for its intended use as described in this manual.
11. Object and Liquid Entry – NEVER push objects of any kind into this product through casing slots as they may touch dangerous voltage points or short out parts that could result in a risk of fire or electric shock. NEVER spill liquid of any kind on the product.
12. Vibration Source – When the Sensor Pad is in use, DO NOT use a bedside crib, cot mobile or other cot accessories that may produce vibrations. Other sources of vibrations may include fans, washing machines, loud music, etc. These sources of vibration may interfere with the performance of your Angelcare monitor and the alarm will not sound if it continues to detect any movement other than your baby’s. Be sure all vibration sources are eliminated before using the monitor.
13. You may experience false alarms for several reasons. The most common reason is the Nursery Unit has not been turned OFF after you have removed your baby from the cot. Another reason is the Sensor Pad has not been placed under the mattress properly. Be sure the Sensor Pad is on a flat, firm surface with the Angelcare logo side facing up. The sensitivity level may also need to be adjusted. Refer to Step 4.3. Always be sure to immediately check on baby whenever an alarm sounds.
14. Sensor Pad – Your Sensor Pad can be used in any cot that is stationary. If the cot has a spring or slat base, place a hard board between the cot base and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick. Only use your Angelcare® monitor in a stationary sleeping environment such as a cot where the Sensor Pad can rest on a completely flat, firm surface. The Sensor Pad is made of plastic and does not permit the air to circulate. Therefore, mildew build up could develop underneath the mattress in the Sensor Pad area. We suggest rotating the mattress regularly to prevent any mildew.

IMPORTANT SAFETY INSTRUCTIONS RELATED TO USE OF BATTERIES

1. Use ONLY the type and size of battery specified in the owner’s manual. There is a risk of explosion if battery is replaced with an incorrect type.
2. DO NOT use rechargeable batteries in the Nursery Unit. Use alkaline batteries ONLY.
3. DO NOT dispose of batteries in fire. They may explode. Check with local regulations for possible special disposal instructions.
4. Exercise care in handling batteries in order not to short out the batteries with conducting materials such as rings, bracelets and keys. Overcharging, short circuiting, reverse charging, mutilation, or incineration of batteries must be avoided to prevent one or more of the following occurrences: release of toxic materials, release of hydrogen and/or oxygen, gas and rise in surface temperature.
5. DO NOT attempt to rejuvenate the battery provided with or identified for use with this product by heating them. Sudden release of battery electrolyte may occur, causing burns or irritation to eyes or skin.
6. If and when necessary, the battery must be replaced with identical new ones or equivalent (volts and size).
7. Reverse polarity installation of the batteries in the end product must be avoided. Reverse insertion of batteries can cause charging, and that may result in leakage or explosion.
8. Remove the battery from this product if you store the product over 30 days because the battery could leak and damage the product.
9. Discard ‘dead’ batteries as soon as possible since ‘dead’ batteries are more likely to leak in a product. If a battery has leaked or vented, it should be replaced immediately using protective gloves.
10. DO NOT store this product, or the battery provided with or identified for use with this product, in high-temperature areas.

SETUP REQUIREMENTS

INCLUDED :Model AC017 Movement Monitor

WHAT YOU WILL NEED (NOT INCLUDED):

STEP 1 – SETTING UP THE NURSERY UNIT

NURSERY UNIT:

INSERT THE BATTERIES
When using the Nursery Unit for the first time, you will need to insert 2 AAA alkaline batteries (not included).
Remove the battery door with a screwdriver and insert 2 AAA alkaline batteries.

SELECT A LOCATION FOR THE NURSERY UNIT
Nursery Unit can be installed using the tabletop stand.

STEP 2 – POSITIONING THE MOVEMENT SENSOR PAD

When using the Sensor Pad for the first time, you will need to insert the provided CR3032 battery.

1.  Remove the battery cover using a coin. Turn in the direction of the arrow.
2. Place the included battery (CR3032) in the compartment. Note: The + symbol should be facing up.
3. Replace the battery cover (the two dots will line up). The Sensor Pad is now ON.

INSTALL THE SENSOR PAD ON THE MATTRESS SUPPORT

IMPORTANT
If your cot does not have a solid, stable surface for the Sensor Pad, you will need to place a support under it, to ensure correct operation of the system. This hardboard support should be at least 6 mm thick and should have minimum dimensions of 33 cm x 33 cm. This support board must be larger than the Sensor Pad surface area. The Sensor Pad functions with any size and type of mattress except memory foam mattresses, hollow frame mattresses, and water beds. The hardboard maintains a constant pressure on the Sensor Pad, enabling it to detect the baby’s movements even when the baby is at the edges of the cot.

1. Remove the mattress from the
2. Place the Sensor Pad – Angelcare logo side up – in the center of the mattress. It should be centered on the hardboard if your cot requires hardboard support.
3. Replace the mattress.

WARNING

• The Sensor Pad is not designed for use with adults, children or infants older than 24 months.
• Discontinue used of the Sensor Pad when baby is older than 24 months. Remove Sensor Pad from cot and store for future use.
• BEFORE FIRST TIME USE: To test that the unit is ready for use, refer to the instruction manual on how to test that the installation has been done correctly.

STEP 3 – TURNING ON YOUR MONITOR

The Nursery Unit will emit a sound and flash blue to confirm pairing with the Sensor Pad

NOTE:
If the green light does not appear but the red light is flashing; or if there are false alarms, adjust the sensitivity level (Step 4.3).

STEP 4 – GETTING TO KNOW YOUR MONITOR

TESTING THE SENSOR PAD:

1. Move your hand lightly on the mattress.
2. Remove your hand from the mattress. After 15 seconds you will hear a pre-alarm sound and the light will flash red.
3. 5 seconds later the Nursery Unit will emit loud continuous beeps and the light will flash red continuously – this is the movement alarm.

MOVEMENT ALARM

• If NO movement is detected after 15 seconds you will hear a single pre-alarm sound from the Nursery Unit.
• If after a further 5 seconds, there is still NO movement detected, Nursery Unit speakers will emit loud continuous beeps – this is the movement alarm.

IF THE ALARM DOES NOT SOUND

• Avoid contact with cot while the Sensor Pad is in operation.
• Place cot near a supporting wall.
• Adjust Sensor Pad sensitivity level.
• Turn OFF cot mobile, fans, loud music or anything else that may cause vibration.

IMPORTANT

• Test your monitor before first use.
• Test your monitor regularly to ensure it is functioning correctly.
• Test your monitor every time you move the Sensor Pad to a different place.

PAUSING AND RESTARTING THE SENSOR PAD:
Allows you to pause the Sensor Pad if you remove baby from the cot, e.g. for feeding or comforting.

1. From the Nursery Unit, press the Pause button on the top right of the unit.
2. The light will flash white when the Sensor Pad is paused. The Nursery Unit will emit a single beep every 20 seconds to indicate movement function is paused.
3. To unpause the Sensor Pad press the Pause button again.

IMPORTANT

• If you do not pause the Sensor Pad, the alarm will sound if there is no movement detected on the surface of baby’s mattress after 20 seconds.
• Ensure to unpause the Sensor Pad before putting baby back in the cot.

TO ADJUST THE SENSOR PAD SENSITIVITY LEVEL:
To ensure adequate monitoring of your baby’s movements, you can adjust the sensitivity of the Sensor Pad. Set a high sensitivity for a newborn and a lower sensitivity as baby grows and gains weight. A thicker mattress will also need a higher sensitivity.
Slide the Nursery Unit sensitivity level button to select between low, medium or high level.

For optimal results begin with the preset sensitivity level and only increase/decrease if required.

IMPORTANT

• The Sensor Pad is not designed for use with adults, children or infants older than 24 months.
• Once you are finished using the Sensor Pad, please deactivate the Movement Function and then remove it from the baby’s cot and store it away.

BATTERIES

NURSERY UNIT LOW BATTERY INDICATOR:
The low battery yellow light indicator will flash and an alarm will sound every 20 seconds when the batteries on the Nursery Unit need to be replaced.

SENSOR PAD LOW BATTERY INDICATOR:
The low-battery yellow light Indicator will flash and an alarm will sound every 20 seconds when the battery on the Sensor Pad needs to be replaced.

TROUBLESHOOTING

FALSE ALARMS

• Turn OFF the Nursery Unit.
• Make sure there is no bedding between the mattress and the Sensor Pad.
• If the cot has a spring or slat base, place a hardboard between the crib base and theSensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure the Sensor Pad is positioned as described under the setup requirements. Sensitivity may need to be adjusted (refer to Step 4.3).
• Re-connect the Sensor Pad and Nursery Unit by pressing and holding the Nursery Unit Pairing button for 2 seconds until the blue light flashes and you hear a beep.

ALARM WILL NOT SOUND

• Avoid contact with the cot when the monitor is ON.
• Place cot near a solid supporting wall to avoid Sensor Pad from detecting movement from outside the cot.
• Turn OFF cot mobile, fans, loud music or anything else that may cause vibration.
• You may need to decrease the sensitivity (refer to Step 4.3).

SENSOR PAD LIGHT INDICATOR FLASHING RED

• Make sure there is no bedding between the mattress and the Sensor Pad.
• The Sensor Pad must rest on a completely flat and firm surface. If the cot has a spring or slat base, place a hard board between the cot base and the Sensor Pad measuring at least 33 x 33 cm and 6 mm thick.
• Make sure Sensor Pad is positioned as described under the setup requirements. Sensitivity may need to be adjusted (refer to Step 4.3).

LOSS OF CONNECTIVITY (NURSERY UNIT BLUE LIGHT FLASHES AND EMITS A BEEP EVERY 20 SECONDS)

• Bring the units closer together.
• Press and hold for 2 seconds the Nursery Unit Pairing button, the Nursery Unit will emit a beep and will flash blue to confirm connectivity.

NO POWER

• Check or replace batteries.
• Make sure the monitor is ON.

LIMITED WARRANTY
Angelcare warrants to the original owner of this product that Angelcare monitor is free from any material and workmanship defects for the term of the warranty period (see warranty table below to determine the warranty for your country). If this monitoring system fails to function properly when used as directed under normal conditions and during the warranty period, Angelcare will either repair or replace the product, at our discretion, free of charge. Please contact your local distributor to validate warranty and warranty period. The product must be accompanied by a proof of purchase, either a bill of sale or other proof that the monitoring system is within the warranty period. Angelcare will bear the cost of repairing or replacing the product and shipping it back to you.
This warranty does not apply to a product that has been damaged as a result of improper maintenance, an accident, improper voltage supply or any other form of misuse. The warranty is also void if the owner repairs or modifies the product in any way. Angelcare is not liable for any incidental or consequential damages with regard to this product. The warranty also excludes any liability other than what is stated above. No other warranty is given.This warranty does not cover products and accessories that are not Angelcare- branded, or any problems that result from usage that is not in accordance with product instructions, failure to follow the product instructions, or problems caused by using accessories, parts or components not supplied by Angelcare.

LEGAL RIGHTS VARY FROM COUNTRY TO COUNTRY. SOME COUNTRIES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS MAY NOT APPLY TO YOU. WE ARE NOT IN ANY WAY RESPONSIBLE FOR ANY OUTCOME RESULTING FROM THE USE OF THIS PRODUCT. IMPORTANT! This Angelcare® monitor is a personal care product. Please do not return this product to the store. If you have questions or need help, please call your distributor before returning this product: international.angelcarebaby.com

WARRANTY TERM PER COUNTRY

• UK, South Africa,
  • Russia 1 year
• Other countries
  • 2 years

TECHNICAL SPECIFICATIONS

Range:
Open field (Open area without obstructions):
up to 8 meters.

Power Supply:
2 AAA alkaline batteries for Nursery Unit
(not included)
1 CR3032 3V battery for Wireless Sensor Pad (included)

Caution : To reduce the risk of electric shock, do not expose this product to rain or moisture.
Danger of explosion if batteries are incorrectly replaced. The battery for the Sensor Pad is a user-replaceable Lithium (not Li-Ion) battery and is NOT rechargeable. Only use the Angelcare-recommended replacement battery. To obtain information on replacement batteries please contact Angelcare customer service: www.angelcarebaby.com or contact your local distributor. Instructions will be included with the replacement battery. Keep all batteries away from children.

Batteries:

• DO NOT mix old and new batteries.
• DO NOT mix alkaline standard (carbon-zinc), or rechargeable (NI-CD, NIMH, etc.) batteries.

CAUTION : RISK OF EXPLOSION IF BATTERY IS REPLACED BY AN INCORRECT TYPE.

Transmission:
Data transmission between the Nursery Unit and the Sensor Pad is made on 2.402 to 2.480 GHz frequency.
Maximum RF Power Transmitted: 4dBm (2.5mW) Hereby, Angelcare Monitors Inc., declares this baby monitor is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of conformity is available at the following internet address: www.angelcarebaby.com/declaration-of- conformity

PROTECT THE ENVIRONMENT
The wheelie bin symbols mean that according to local laws and regulations, your product and/or its battery shall be disposed of separately from household waste. When the product/battery reaches its end of life take it to a collection point designated by local authorities. The seperate disposal and recycling will help conserve natural resources and protect human health and the environment. Refer to the User’s Guide for the removal of batteries.

For assistance, FAQs or guidance with your monitor please visit our Customer Support page at Angelcare.co.uk
www.angelcarebaby.com

References

• Angelcare – angelcarebaby
• Manual-Hub.com - Free PDF manuals!
• Angelcare – angelcarebaby
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>