Atlas Metal TFT Mobile Tubular Frame Tray And Rack Dispensers User Manual
- June 17, 2024
- Atlas Metal
Table of Contents
**Atlas Metal TFT Mobile Tubular Frame Tray And Rack Dispensers User Manual
**
WARNING! INSPECT UNIT THOROUGHLY FOR ANY DAMAGE THAT MAY HAVE OCCURRED DURING SHIPMENT BEFORE LOADING.
OPERATION
Load items on carrier tray, “DO NOT DROP” check to see if items fit on carrier tray with no more than 1″ of side play. When fully loaded, push down on load and slowly release to allow load to set at proper dispening height.
WARNING:
READ “REMOVAL OF ELEVATORS INSTRUCTIONS BEFORE SERVICING THIS UNIT, TO
AVOID PERSONAL INJURY. THE ELEVATOR ASSEMBLIES ARE UNDER EXTREME PRESSURE, USE
EXTRA CARE!
REMOVAL OF ELEVATORS
The removal of the elevator assembly is a simple procedure using only an 8 penny nail 2 1/2″ long. To begin, remove the carrier tray lift by using hole provided. Push down on elevator crossarm bracket to expose hole 2″ from the top of the small inner tube to insert the nail (fig. 1). Release tension until crossarm bracket tubing rests against the nail. Lift the elevator approx. 1/4″ and move the bottom of the elevator toward the center of the dispenser. And downward until elevator is free from top bracket **(fig. 2). REVERSE ABOVE PROCEDURE FOR INSTALLING ELEVATORS.
**
CHANGING OF SPRINGS
Now that the elevator is free from the dispenser it can be dissambled. “EXTRA CARE MUST BE TAKEN THAT THE ELEVATOR DOESN’T SPRING APART WHEN DISASSEMBLING.” Place the elevator in an upright position with the bottom firmly against the floor. Push down on the crossarm bracket approx. 3″ to 4″ to release spring tension on the crossarm, and to remove the nail. Gradually release spring tension to remove springs. Lay the elevator on a flat surface and pull tubing apart to expose springs to be removed, and replace springs. INSTALL SPRINGS WITH CUT SIDE DOWN.
GENERAL INFORMATION
TROUBLE SHOOTING:
Load uneven upon return: Tubing dented/Springs caught in tubing See
elevator removal/spring change.
Tray/Rack won’t dispense: Incorrect springs specified check Resubmit
tray/rack data.
Unit won’t roll: Inspect wheels for damage Possible debris on axle Clean
or replace as necessary.
DISPENSING PROBLEMS PERSIST…
PUT DISPENSER OUT OF SERVICE! CALL FACTORY FOR SERVICE AUTHORIZATION. USE
LICENSED QUALIFIED SERVICE PERSONNEL ONLY!
CLEANING INSTRUCTIONS:
TO CLEAN, WIPE DISPENSER THOROUGHLY WITH DAMP CLOTH AND MILD SOAP SUITABLE
FOR USE IN FOOD CONTACT ZONES. “NO ABRASIVES.”
PARTS LIST
CONTACT FACTORY FOR PART NUMBERS AND PRICING. HAVE MODEL NUMBER AVAILABLE.
SPECIFICATIONS
SELF-LEVELING MECHANISM:
The dispenser shall be equipped with automatic Self-Leveling compression type
ELEVATORS (all stainless steel components). Each ELEVATOR shall consist of
properly calibrated non-fatiguing stainless steel compression springs
completely encased in die stamped stainless steel telescoping tubing. The
ELEVATORS shall be connected by a removable platform carrier constructed of
heavy gauge grade 18-8 stainless steel. The ELEVATORS and platform carrier are
removable for cleaning.
FRAMEWORK:
The framework shall be constructed of 16 gauge, 1″ O.D. grade 18-8 stainless
steel tubing, with the vertical frame welded to base frame for additional
strength. Frame shall have stainless steel upper horizontal and vertical guide
rods welded to the 1º O.D. tubing for additional strength. All dispensers
shall be furnished with 4 diameter, non-marking, heavy duty, full swivel
casters (bolt-on type) and gray non-marking comer bumpers. Empty rack guides
shall be supplied on TFR models.
TRAY DISPENSERS MODEL TFT
MODEL| MAXIMUM
WEIGHT| L & W| SHIPPING
WEIGHT
---|---|---|---
TFT-1216| 12 5/8″ x 16 3/8″| 19 x 17 5/8″| 51 LBS.
TFT-1418| 14 5/8″ x 18 3/8″| 21″ x 19 5/8″| 53 LBS.
TFT-1520| 15 5/8″ x 20 3/8″| 23″ x 20 5/8″| 62 LBS.
TFT-1622| 16 5/8″ x 22 3/8″| 25″ x 21 5/8″| 70 LBS.
TFT2-1014| 10 7/8″ x 15″| 25″ x 20″| 70 LBS.
RACK DISPENSERS MODEL TFR
MODEL| MAXIMUM
WEIGHT| L & W| SHIPPING
WEIGHT
---|---|---|---
TFR-1020| 10 1/4″ X 20 1/4″| 23″ X 15 5/8″| 60 LBS.
TFR2-1020| 10 1/4″ X 20 1/4″| 24 3/8″ X 25 5/8″| 87 LBS.
TFR-2020| 20 1/4″ x 20 1/4″| 23″ X 25 5/8″| 86 LBS.
TFR-18J| 18″ diameter| 21 X 23 5/8″| 82 LBS.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>