Aventek ‎BA-11 Wireless Door Bell User Manual

Aventek ‎BA-11 Wireless Door Bell

Thank you for purchasing this product. To ensure proper use and trouble- free operation, please read this manual carefully and store it in a safe place for future reference.

Introduction

• This doorbell kit includes one transmitter and one battery-powered receiver. It is battery-powered and requires no wiring work, making setup a breeze. Featuring 52 tunes and melodies with an adjustable volume control, the doorbell kit suits many different circumstances. It can be expanded for further coverage and convenience.
• Add it to your home, office, shop etc. and be immediately informed whenever there is a visitor.

Package Contents

• 1 x Transmitter (battery included)
• 1 x Battery-powered receiver (3 AAA batteries included)
• 4 x Anchors
• 4 x Screws
• 1 × Key
• 1 x Adhesive patch
• 1 x Mounting bracket
• 1 x User manual

Technical Specifications

Product Overview

1. Volume Button
2. Chime Selection Buttons
3. Receiver LED
4. ransmitter LED
5. Battery Compartment
6. Battery Compartment Cover
7. Mounting Bracket

Features

1. Utilizing a 3 V lithium coin cell, the transmitter is estimated to last up to 3 years when used 10 times per day without battery replacement.
2. The transmitter is IP55 dustproof and waterproof, suitable for various outdoor environments.
3. The doorbell boasts a massive wireless range of up to 300 m.
4. For enhanced convenience, the receiver is designed with chime selection buttons for easy selection from among the rich selection of 52 chimes. Five volume levels can be easily adjusted using the volume button.
5. The memory function of the receiver remembers your previous melody and volume level even after re-installing the battery.
6. The receiver uses 3 AAA batteries and features highly efficient power management for low power consumption and enhanced battery life.
7. The receiver features a low battery power reminder via LED notification and will check the battery level each time the battery is replaced.

Installation

Transmitter Battery Unsealing

Before first use, gently pry open the rear cover of the transmitter and peel off the seal on the button cell. Ensure correct polarity of the battery and close the battery compartment cover.

Transmitter Installation

To ensure sufficient wireless range, do not install the transmitter close to metals.

Adhesive Tape (recommended for water resistance)

1. Clean all surfaces to be used for adhesion with rubbing alcohol.
2. Apply the double-sided adhesive patch to the back of the transmitter.
3. Remove the outer side of the patch, attach the transmitter to the desired location and press it firmly for 30 seconds.

Anchored Screws

1. Gently pry open the rear cover of the transmitter and drill out the marked screw holes.
2. Drill holes for the screws at the desired location and insert the anchors.
3. Attach the rear cover to the wall by tightening it with the screws.
4. To ensure resistance against water, seal the screw holes with silicone.
5. Attach the transmitter onto the screwed-on back cover.

Receiver Installation

Choose an installation location with as few obstacles to the transmitter(s) as possible.

1. Drill holes at the desired location and insert the anchors.
2. Attach the mounting bracket to the wall by tightening it with the screws.
3. Hook the receiver onto the mounting bracket.

Operating Instructions

Transmitter and Receiver Pairing

Up to two transmitters can be paired with a single receiver. One transmitter can be paired with up to two receivers.

1. Install 3 AAA batteries into the receiver. Adjust the volume level with the volume button if the receiver doesn’t ring while flashing.
2. Press and hold the volume button on the receiver for 3 seconds. The receiver LED will blink either green or red to indicate the pairing mode channel. Press any button on the receiver or wait for 60 seconds to exit pairing mode.
3. Press the transmitter button to pair it with the receiver. The “ding-dong” chime indicates a successful pairing. From now on the receiver LED will light up with the color that was blinking during pairing with the paired transmitter.

Chime Selection

1. There are 52 chimes to choose from with this doorbell kit. Simply press the chime selection buttons repeatedly to select one you prefer, saving you the hassle of cycling through the whole list if you accidentally miss your desired chime.

Volume Adjustment

1. There are five volume levels in total with the minimum volume level being silent. Press the volume button repeatedly to cycle through the volume levels and set one to suit your needs.

Maintenance and Care

Transmitter Battery Replacement

1. When the transmitter connection starts to fail, it is time to replace the battery. Gently pry open the rear cover of the transmitter and replace it with the battery of type CR2032 according to the polarity markings.

Receiver Battery Replacement

1. The receiver LED flashes in red every two seconds if the batteries are low and need to be replaced.
2. Open the battery compartment and replace 3 type AAA batteries according to the polarity markings.

Troubleshooting

The transmitter does not work.

| The battery seal has not been removed.| Remove the seal of the transmitter battery.
The battery is not properly installed.| Ensure that the coin battery is installed with the correct polarity orientation.
Low battery power.| Replace the transmitter battery.
The receiver does not ring when the transmtter is being pressed.| ****

The receiver is not paired with the transmitter.

| ****

Pair the transmitter and

receiver again.

Frequently Asked Questions

How far can the Aventek BA-11 Wireless Door Bell transmitter be from the receiver?

The Aventek BA-11 Wireless Door Bell boasts a wireless range of up to 300 meters, providing reliable signal transmission even across large distances.

Can I use multiple transmitters with one receiver, or vice versa, with the Aventek BA-11 Wireless Door Bell?

Yes, you can pair up to two transmitters with a single receiver, and one transmitter can be paired with up to two receivers. This flexibility allows you to expand coverage and convenience throughout your home or office.

How long do the batteries typically last in the Aventek BA-11 Wireless Door Bell transmitter and receiver?

The transmitter, powered by a CR2032 lithium coin cell, is estimated to last up to 3 years when used 10 times per day without needing a battery replacement. The receiver, powered by 3 AAA batteries, has a battery life of up to 1 year with similar usage patterns.

Is the Aventek BA-11 Wireless Door Bell suitable for outdoor use?

Yes, the transmitter of the Aventek BA-11 Wireless Door Bell is IP55 dustproof and waterproof, making it suitable for various outdoor environments. However, it's essential to ensure proper installation to maintain its durability.

How many chimes and melodies are available with the Aventek BA-11 Wireless Door Bell?

The Aventek BA-11 Wireless Door Bell offers a rich selection of 52 tunes and melodies, providing users with ample options to choose from. Additionally, the chime selection buttons on the receiver make it easy to cycle through and select your preferred chime.

What should I do if the receiver doesn't ring when the transmitter is pressed with the Aventek BA-11 Wireless Door Bell?

If the receiver doesn't ring when the transmitter is pressed, first ensure that the transmitter and receiver are properly paired. If not, follow the pairing instructions provided in the manual to establish the connection. If the issue persists, consider checking the battery levels and replacing them if necessary.

How do I adjust the volume of the Aventek ‎BA-11 doorbell chime?

Use the volume button on the receiver to adjust the volume level. There are five volume levels available, including a silent mode.

Can I install multiple receivers throughout my home or office?

Yes, you can install multiple receivers in different areas of your home or office to ensure that you hear the doorbell from various locations.

What is the wireless range of the Aventek ‎BA-11 doorbell transmitter?

The doorbell boasts a wireless range of up to 300 meters, providing reliable signal transmission throughout your property.

Is the doorbell waterproof and suitable for outdoor use?

Yes, the doorbell transmitter is IP55 dustproof and waterproof, making it suitable for various outdoor environments.

How do I pair additional transmitters with the receiver?

To pair additional transmitters, simply follow the pairing instructions provided in the user manual. You can pair up to two transmitters with a single receiver.

Can I customize the Aventek ‎BA-11 chime sound on the doorbell?

Yes, the doorbell offers 52 different chime sounds to choose from. Use the chime selection buttons on the receiver to cycle through the available options and select your preferred sound.

Video- Installation

Download The PDF link:Aventek ‎BA-11 Wireless Door Bell User Manual

Reference:Aventek ‎BA-11 Wireless Door Bell User Manual- device.report

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>