beko HCA63640BH Wall Cooker Hood User Manual

Hood
User manual

HCA63640BH Wall Cooker Hood

HCA63640B/HCA63640BH
HCA93640BH/HCA93641BH
HCA63640Z/HCA63640W

01M-8861023200-3120-06
01M-8895343200-3120-06
01M-8861053200-3120-06
01M-8895383200-3120-06
01M-8861063200-3120-06
01M-8895503200-3120-06
01M-8802543200-3120-06
01M-8895513200-3120-06
01M-8802773200-3120-06
01M-8895393200-3120-06
01M-8808883200-3120-06
01M-8895413200-3120-06

Please read this user manual first!
Dear Valued Customer,
Thank you for preferring this Beko appliance. We hope that you get the best results from your appliance which has been manufactured with high quality and stateof-the-art technology.  For this reason, please read this entire user manual and all other accompanying documents carefully before using the appliance and keep it  as a reference forfuture use. If you handover the appliance to someone else, give the user manual as well. Follow the instructions by paying attention to all the information and warnings in the user manual.
Remember that this user manual may also apply to other models. Differences between models are explicitly described in the manual.

Meanings of the Symbols
Following symbols are used in various sections of this user manual:

| Important information and useful hints about usage.
---|---
| WARNING: Warnings against dangerous situations concerning the security of life and property.
| Warning for danger of fire.
| Warning for electric shock.

This product was manufactured using the latest technology in environmentally friendly conditions.
Complies with the WEEE Directive.
**** Does not contain PCB.

Important instructions for safety and environment

1.1 General Safety
Important Safety Instructions Read Carefully And Keep For Future Reference This section contains safety instructions that will help protect from risk of fire, electric shock, exposure to leak microwave energy, personal injury or property damage. Failure to follow
these instructions shall void any warranty.

• Beko products comply with the applicable safety standards; therefore, in case of any damage on the appliance or power cable, it should be repaired or replaced by the dealer, service center or a specialist and authorized service alike to avoid any danger. Faulty or unqualified repair work may be dangerous and cause risk to the user.

• This appliance is intended to be used in household and similar applications such as:
  – Staff kitchen areas in shops, offices and other working environments;
  – Farm houses
  – By clients in hotels, and other residential type environments;
  – Bed and Breakfast type environments.

• Operate the appliance for its intended purpose only as described in this manual.

• The manufacturer cannot be held liable for damages resulting from improper installation or misuse of the product.

• This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a  safe way and understand the hazards involved.

• Children shall not be allowed play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• The minimum distance between the supporting surface for the cooking vessels on the hob and the lowest part of your product must be at least 65 cm.

• If the instructions for installation for the gas hob specify a greater distance, this has to be taken into account.

• Make sure that your mains power supply complies with the informa- tion supplied on the rating plate of the appliance.

• Never use the appliance if the power cable or the appliance itself is damaged.

• Prevent damage to the power cable by not squeezing, bending, or rubbing it on sharp edges. Keep the power cable away from hot surfaces and naked flame.

• Use the appliance with a grounded outlet only.
  WARNING: Do not connect the appliance to the mains until the installation is fully complete.

• Place the appliance in a way so that the plug is always accessible.

• Do not touch the lamps if they have operated for a long time. They can burn your hands since they will be hot.

• Follow the regulations set out by competent authorities on dis- charge of the exhaust air (this warning is not applicable for use without flue).

• Operate your appliance after putting a pot, pan etc. on the hob. Otherwise, high heat may cause deformation in some parts of your product.

• Turn off the hob before taking the pot, pan etc. from it.

• Do not leave hot oil on the hob. Pans with hot oil may cause self combustion.

• Pay attention to your curtains and covers since oil may catch fire while cooking food such as fries.

• Grease filter must be replaced at least monthly. Carbon filter must be replaced at least every 3 months.

• Product shall be cleaned accordance with user manual. If cleaning was not carried out in accordance with user manual, there may be fire risk.

• Do not use non-fire-resistant filtering materials instead of the current filter.

• Only use the original parts or parts recommended by the manufacturer.

• Do not operate the product without the filter and do not remove the filters while the product is running.

• In the event of be started any flame, de-energize your product and cooking appliances.

• In the event of be started any flame, cover the flame and never use water to extinguish.

• Unplug the appliance before each cleaning and when the appliance is not in use.

• The negative pressure in the environment should not exceed 4 Pa (4 x 10 bar) while the hood for electric hob and appliances running  on another type ofenergy but electricity operate simultaneously.

• In the environment where the appliance is being used, the exhaust of devices running on fuel oil or gas, such as room heater must be absolutely isolated or device must be hermetical type.

• When connecting the flue, use pipes with a diameter of 120 or 150 mm. Pipe connection must be as short as possible and have as few elbows as possible.
  Danger of choking! Keep all the packaging materials away from children.
  CAUTION: Accessible parts may become hot when used with cooking appliances.

• The product outlet must not be connected to air channels that in- clude other smoke.

• The ventilation in the room may be insufficient when the hood for electric hob is used simultaneously with the devices operating on gas or other fuels (this may not apply to appliances that only discharge the air back into the room).

• Objects placed on the product may fall. Do not place any objects on the product.

• Do not flambe under the your product.
  WARNING: Before installing the Hood, remove the protective films.

• Never leave high naked flames under the hood when it is in operation

• Deep fat fryers must be continu- ously monitored during use: over- heated oil can burst into flames.

1.2 Compliance with the WEEE Directive and Disposing of the Waste Product: This product complies with EU WEEE Directive (2012/19/EU). This product bears a classification symbol for waste electrical and electronic equipment (WEEE).

**** This symbol indicates that this product shall not be disposed with other household wastes at the end of its service life. Used device must be returned to offical collection point for recycling of electrical and electronic devices. To find these collection systems please  contact to your local authorities or retailer where the product was puchased. Each household performs important role in recovering and recycling of old appliance. Appropriate disposal of used appliance helps prevent potential negative consequences for the environment and human health.

1.3 Compliance with RoHS Directive
The product you have purchased complies with EU RoHS Directive (2011/65/EU). It does not contain harmful and prohibited materials specified in the Directive.

1.4 Package Information
**** Packaging materials of the product are manufactured from recyclable materials in accordance with our National Environment Regulations. Do not dispose of the packaging materials together with the domestic or other wastes. Take them to the packaging material collection points designated by the local authorities.

Technical specifications of your appliance

1. Inner Chimney
2. Outer Chimney
3. Glass Cover
4. Control Panel
5. Lightning

| HCA63640B-W| HCA63640BH| HCA93640BH| HCA93641BH| HCA63640Z
---|---|---|---|---|---
Width| 596 mm| 596 mm| 896 mm| 896 mm| 596 mm
Depth| 410 mm| 410 mm| 410 mm| 410 mm| 410 mm
Height| 750 mm/1080 mm| 750 mm/1080 mm| 750mm/1130 mm| 750mm/1130 mm| 750 mm /1080 mm
Supply voltage| 220 – 240 V- 50 Hz| 220 – 240 V- 50 Hz| 220 – 240 V- 50 Hz| 220 – 240 V- 50 Hz| 220 – 240 V- 50 Hz
Control| With 3 levels| With 3 levels| With 3 levels| With 3 levels| With 3 levels
Lamp power| 2 x 3W| 2 x 3 W| 2x3W| 2 x 3 W| 2x 3 W
Air outlet pipe| 120 /150 mm| 120 /150 mm| 120 /150 mm| 120 /150 mm| 120 / 150 mm
Motor power| 210 W| 210 W| 210 W| 210 W| 210 W
Total power| 216W| 216W| 216W| 216W| 216W
Colour| B=Black W=VVhite| Zara grey

Values stated on the product labels or in the documentation accompanying it are obtained in laboratory conditions in accordance with relevant standards. These values may vary depending on operational and environmental conditions of the product.

Installing your appliance

WARNING
Please consult the nearest Authorised Service Agent for the installation of your hood.
WARNING
*Preparation of location and electrical installation for the product is under customer’s responsibility.
WARNING
Remove the protective film (if any) on the hood and flue surface after the installation.

Distance between lower surface of the hood and upper surface of the hob should be at least 65 cm.
Have a qualified electrician make the electrical connection.
Install your appliance so that you can reach the power connection (plug, outlet) easily after installation.
Dimensions are given in mm.

3.1 Installation accessories
Information required for the preparation of the installation place for your hood is given below.
3.2 Installing the hood onto the wall
To install the hood onto the wall, loosen the screws of hanger plates on the motor housing and pull the plates upwards. Then, tighten the screws of the hanger plates. (Figure 3a). If you will use Ø 120 mm flue pipe, install Ø 120 mm flue adapter onto it.

3.2.1 Boring the hanger holes
Affix the installation template onto the installation place of the hood. Drill the points market with (X,Y) (Figure 4) using a Ø 8 mm bit and points market with (Z) (Figure 4) using a Ø 6 mm bit.

3.2.2 Hammering the wall plugs
Hammer Ø 8 mm wall plugs (X,Y) into the holes drilled for hanger screws. Hammer 2 x Ø 6 mm wall plugs (Z) into the holes drilled with a Ø 6 mm bit for the external flue connection plate. (Figure 5)
3.2.3 Installing the hanger screws
Install 4.9×50 hanger screws into the Ø 8 mm wall plugs (Y) you have hammered into the wall. There must be a gap of 5 mm between the screw head and the wall. (Figure 5)
Connect the internal flue connection plate to the 8 mm wall plugs (Z) on the wall using Ø 3.9×22 screws. (Figure 5)

3.2.4 Hanging the hood onto the wall

• Hang the hood onto the screws you have installed into the Y holes.
• Open the side suction window of the hood by pulling it towards yourself. Install the 4.9×50 screws through the X holes located inside in order to secure the appliance.

3.3 Installing the hood flue
Disconnect the product from mains supply before starting flue installation. Fit the sheet metal flue parts around the body.
Screw the external flue to the external flue connection plates located on the motor housing. (Figure 3b / 6)

Extend and screw the internal flue from its outer edges onto the flue connection plate which was secured to the wall (Figure 7).

3.4.1 Using with flue connection

• The vapour is removed via flue pipe which is secured to the connection head on the hood.
• Diameter of the flue pipe should be equal to the diameter of connection ring. To allow the air be removed easily out of the room in horizontal arrangements, the pipe should be slightly tilted upwards (approximately 10°).

3.4.2 Using without flue connection

• Air is filtered by the carbon filter and returned to the room. Carbon filter is used when there is no flue in the house.
• If the hood will be used without flue connection remove the diverters inside the flue adapter.
• Remove the aluminum filter. To install the carbon filter, center the carbon filter on the plastic part on both sides of the fan body, and secure it on the tabs. Secure the filter by turning the tabs to right or left.
• Install the aluminum filter.

3.5 Flue connection:
Place adapter supplied together with the hood into the ventilation hole located on the top section of the hood. Procure a pipe with a diameter of 120/150 mm. Connect one end of the pipe to the adapter and the other end to the flue.
Make sure that these two connections are secure enough so that they will not dislocate when the hood is operated in max. speed. Check that the flaps inside flue are functional when tightened with the clamp. Fit the flue connection pipe onto the adapter. If you fit the flue connection pipe inside the adapter, air suction will not occur since the flaps that prevent air backflow will remain closed.
It is not advisable to make connections to the flues connected with stoves or exhaust shafts. Do not make connections to such flues.

Pipe connection must be as short as possible and have minimum number of elbows.
A: Flue outlet pipe
B: Flaps that prevent backflow
C: Plastic flue
3.5.1 Backflow prevention system (N-RV)
When the hood is operated, flaps are closed in order to prevent possible odours and dust from entering into the ambient from outside.

Operating your appliance

(A): 1st level key
(B): 2nd level key
(C): 3rd level key
(D): Light On / Off key

4.1 Digital electronic control with 3 levels
(A) You can start your hood at speed level 1 by pressing this key.
When you press this key again to switch off the appliance, speed level indication on the display disappears.
(B) key: You can start your hood at speed level 2 by pressing this key.
When you press this key again to switch off the appliance, speed level indication on the display disappears.
(C) key:You can start your hood at speed level 3 by pressing this key.
When you press this key again to switch off the appliance, speed level indication on the display disappears.
(D) key: Light On/Off Key: You can illuminate the cooking area by pressing this key.

Auto-stop in 15 min.:
This appliance is equipped with an Auto-Stop function which allows the appliance to ventilate the room for an additional period of time in order to remove the unpleasant odour and vapour in the room after the cooking is over. Appliance stops automatically after a certain period of time.
To enable the Auto-stop function, press any of the speed level keys (A, B, C) on the control for longer than 2 seconds. A timer with 15 minutes will be activated.
If you press the same speed level key while the Auto-stop function is enabled, function will be disabled and the appliance will stop.
If you select a different speed level this function will be disabled.
If you want your appliance to stop automatically, you must enable the Auto- stop function again.
Periodical cleaning of metal filters:
Filters must be cleaned at about every 60 hours of operation or 4 weeks depending on the frequency of usage.

4.2 Energy efficient usage:

• When operating the hood, adjust the speed level according to the odour and vapour intensity in order to prevent unnecessary power consumption.
• Use low speeds in normal conditions (1-2), and high speed (3) when smell and vapors are inten- sified.
• Lights on the hood are intended for illuminating the cooking zone.

Using them to illuminate the ambient/kitchen will result with unnecessary power consumption and inadequate illumination.

4.3 Operating the hood:

• Hood is equipped with a motor having various speed settings.
• For a better performance, we advise you to use low speeds in normal conditions, and high speeds when smell and vapors are intensified.
• You can start the hood by pressing the desired speed level key (A,B,C).
• You can illuminate the cooking area by pressing the light key. (D)

Cleaning and maintenance

Prior to cleaning and maintenance, unplug the appliance or turn the main switch off or loosen the fuse that supplies the hood.
5.1 Aluminum filter
This filter captures oil particles in the air. You are recommended to clean your filter every month under normal usage conditions. First remove the aluminum filters for this process. Wash the filters with liquid detergent and rinse them with water and install them back after they get dry. Aluminum filters may get discolored as they are washed; this is normal and you don’t need to change your filter.

5.1.1 Removing the aluminum filters

1. Push the aluminum filter lock forward.
2. Then, slightly lower it and pull forward.
   Otherwise, you may bend the filter. (Figure 9)
   After the aluminum filter is washed and dried, reinstall the filter to its slot by applying above steps in reverse order.

You can also wash aluminum filters in dishwasher.

Carbon filter (Using without flue)
This filter removes the cooking odours. If it is not possible to use a flue, it purifies the air which is circulated inside the kitchen. Carbon filter of your appliance will get clogged in time depending on the frequency of use, style of cooking and regular cleaning of the aluminum filters.

Caution!
Carbon filter should never be washed.

You may obtain carbon filters from Beko Authorised Service Agents.
5.2.1 Replacing the carbon filter

• Remove the aluminum filters. (Figure 9)
• To remove carbon filter, turn the tabs counterclockwise and release the filter. (Figure 10
• Install the new carbon filter.
• Install the aluminum filters.

Anti-odor filters contain charcoal (active carbon).
They must be changed with periods of approximately 6 months.
Regardless of using a carbon filter or not, aluminum filters must always be installed.
Do not operate your appliance without the aluminum filter in place. Using with carbon filter will decrease suction performance of the appliance.

5.3 Cleaning
Particularly do not neglect to clean your hood immediately after you have made frying.
Use a soft cloth soaked with liquid detergent to clean the outer surface of your hood. Never use abrasive or scratching materials for cleaning.
You may use the cleaning agents commercially available for persistent grease etc. by following the warnings on the product. In order not the scratch the brushed steel body, wipe in the same direction with the bush trace. Do not use cleaning agents containing hydrochloric acid, bleach or abrasive powders in order to maintain the surface quality of your product. Use a cloth dampened in soapy water or special stainless steel cleaning spray for stainless steel steel surfaces. Remove the protective foil on the appliance.

Caution!
You may cause a fire if you do not follow the instructions on the cleaning and replacement of the filters of your hood.

If you need to transport the appliance:

• Keep the original packaging of the appliance. Transport the appliance with its original package, and follow the transport markings on the original package.

If you do not have the original package:

• Do not place any objects on the hood.
• Protect the outer surface from impacts.
• Pack the appliance so that it would not be damaged during transport.

5.4 Replacing the lamps
Disconnect the hood from the mains supply.
This appliance is equipped with 3 W halogen lamps.
To replace the halogen lamps, press the lamp downwards from the rear section of the lamp holder to release the lamp. Then turn it counterclockwise by 1/4 tour and remove it.
Perform the above steps in reverse order to fit the new lamps.

You may procure lamps from Authorised Service Agents.

Troubleshooting

restore it.
Appliance is not working.| Check the electrical connection.| Mains voltage shall be between 220 and 240 V.
Appliance is not working.| Check the electrical connection.| Check if other appliance in your kitchen operate.
Illumination light does not operate.| Check the electrical connection.| Mains voltage shall be between 220 and 240 V.
Illumination light does not operate.| Inspect the lamp switch.| Lamp switch shall be at”on” position.
Illumination light does not operate.| Inspect the lamps.| The lamps of the appliance shall illuminate.
Air inlet of the appliance is inadequate.| Inspect the aluminium filter.| Under normal operating conditions, aluminium gre-ase filter shall be cleaned at
least once in a month.
Air inlet of the appli ance is inadequate.| Check the air discharge chimney.| The air discharge chimney shall be at position.
Air inlet of the appliance is inadequate.| Inspect the carbon filter.| The filters of the appliances with carbon filters shall be replaced once in every 3 months under normal conditions.

www.beko.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>