CARVIN EM900S UHF PLL Stereo Mono In Ear Monitor System Instruction Manual

**CARVIN EM900S UHF PLL Stereo Mono In Ear Monitor System Instruction Manual

**

Product Using Instruction

ATTENTION

INTRODUCTION

Thank you for purchasing the Carvin EM00S wireless in-ear monitor system.
The combination of professional features and transparent sound will enable you to experience a new level of monitoring quality. Take the time to read through the manual to get the most out of your new system.

IMPORTANT PRECAUTIONS:

• Make all connections before AC power is connected.
• Avoid exposure to high temperature or humidity.
• Do not handier the transmitter or AC cord in wet conditions.
• Keep away from heat and flame.
• Avoid prolonged listening at high levels.
• Read the OSHA recommendations for hearing safety on the inside cover of this manual.

FEATURES:

SYSTEM:
UHF operation. PLL (Phase Locked Loop) technology provides a reliable signal connection. 960 selectable channels allow you to avoid busy frequencies and external interference. 4 groups of 16 presets allows quicker setup. MPX stereo or Mono operation.
TRANSMITTER:
Metal chassis. Backbit LCD display. Front panel headphone monitor. XLR or 1/4” inputs Lockout mode prevents accidental adjustments. Effect inserts allow use of external processing. -10dB input level switch.
RECEIVER:
Metal chassis. Backlit LCD display with adjustable backlight off time. Built in limiter. HF boost setting. Lockout mode prevents accidental adjustments. Volume and Balance controls. Secure battery pack uses 2 AA batteries lasting 12 frs. Flexible antenna
EARPHONES:
Ergonomic in-ear fit with multiple sized silicone earpieces. Metal braid cord. Full range natural sound.

SPECIFICATIONS:

SYSTEM SPECIFICATIONS:
Frequency Response: 30Hz-15kHz (-3dB) S/N ratio: 80dB (A weighted)
Image frequency rejection: 80dB
Channel separation: 35dB
Input level switch: 0dB/-10dB AC input: 100-240V (switch-mode supply)
Receiver power: 2 AA batteries.
Battery life: 12 hours (approx.)
Net weight: EM900 base: 3.2lbs. (1.45kg.)
EM901 receiver: 0.45lbs. (0.2kg.)
Dimensions: EM900: 1.75″H x 8.35″W x 9.00″D (10.30″D with antenna and AC cord)
EM901: 4.50″H x 2.75″W x 1.00″D (without clip)
EM902 EARPHONE SPECIFICATIONS:
Frequency Response: 10Hz-20kHz
Transducer type: Dynamic
Impedance: 16ohms
Sensitivity @1kHz: 114dB/mW
Distortion: less than 0.3%
Cord length: 58″

CONTROL LAYOUT:

EM900 TRANSMITTER FRONT PANEL

1. POWER SWITCH

2. DISPLAY

3. (+)BUTTON

4. SET BUTTON

5. (-) BUTTON

6. VOLUME CONTROL

7. MONITOR VOLUME

8. STEREO MONITOR JACKS

9. ANTENNA
   

10. AC POWER SOCKET AND FUSE

11. LOOP OUTPUT JACKS

12. INPUT XLR/1/4″ JACKS

13. ANTENNA BNC CONNECTOR
    EM900 TRANSMITTER REAR PANEL
    

EM901 RECEIVER

14. ANTENNA

15. POWER SWITCH / VOLUME

16. BALANCE CONTROL

17. 1/8″ (3.5MM) HEADPHONE JACK

18. BACKLIT DISPLAY

19. (+) BUTTON

20. (- ) BUTTON

21. SETBUTTON

22. BELT CLIP

23. BATTERY PACK
    EM902 EARPHONES
    

24. PLUG

25. SILICONE INSERTS

26. BODY

SETUP:

EM900 TRANSMITTER
A. ATTACH ANTENNA Plug the antenna into the rear panel BNC connector (#14) and rotate the barrel 90 degrees clockwise until it locks into place.

ATTACH AC POWER CORD Firmly insert the provided AC cord into the rear panel AC power socket (#11).
C. CONNECT INPUTS TO SOURCE Using XLR or 1/4” plugs, connect the output of your mixer to the input jacks (#12) on the rear panel of the EM00 transmitter. One jack may be used if the transmitter and receiver are set for “MONO”. f there is no sound, set the BALANCE to center.
EM901 RECEIVER
A. INSERT BATTERIES First, remove the battery pack from the receiver by pressing in the two tabs **(see fig. 1)

at the bottom of the unit and sliding out the battery pack. Open the battery pack by sliding the battery cover off (see fig.2)**.

Insert the batteries as shown on the battery pack and slide the cover back into position. Slide the battery pack back into the receiver.

B. PLUG IN EARPHONES Plug the EM902 earphones into the headphone jack (#17) on the receiver. Atach a pair silicone sleeves (#25) to the ends of the earphones. Follow the “L” and “R” markings on the earphones for left and right ear. Place the end of the earphone at the end of the ear canal and set the body of the earphone (#26) so your outer ear will hold it in place. The earphones should be worn with the wire hanging over the top of the ear as shown in fig.3

TRANSMITTER SETTINGS:

FREQUENCY SETTING
Set the transmitter and the receiver to the same frequency.

1. Press the SET button for 2 seconds until *FREQ” flashes on the display.
2. Set the frequency with the (+) and (-) buttons.
3. Press the SET button to store the frequency.

GROUP AND CHANNEL SETTING
Once you set a frequency, you can store it as a channel, in a group. Each group can store 16 channel presets. Match these settings to the receiver.

1. Press SET for 2 seconds until “FREQ” flashes on the display
2. . Press SET again and “GROUP” and “G” will flash.
3. Press the (+) and (-) buttons to set the group to A,B C, or D.
4. Press SET again and “GROUP” and “CH” will flash 5. Press the (+) and (-) buttons to set the channel to 1-16.
5. Press SET to store the group and channel

STEREO or MONO/MIX MODE SETTING
In Mono/Mix mode, both inputs can be used, and the mix of the 2 inputs can be adjusted from the receiver by using the BALANCE control

1. Press SET for 2 seconds until “FREQ” flashes on the display.
2. Press the SET button 3 times and *MODE” will flash
3. Press (+) for Stereo or (-) for Mono/Mix mode 4. Press SET to store.

ATTENUATION MODE SETTING
The Attenuation mode -10dB is used when very strong signals are present at transmitter inputs. The 0d B mode is used for moderate and weaker signals.

1. Press SET for 2 seconds until “FREQ” flashes on the display.
2. Press the SET button 4 times and *ATT.” will flash.
3. Press (+) for 0dB normal or (-) for -10dB attenuated mode.
4. Press SET to store.

LOCK SETTING
The Lock feature helps prevent accidental changing of settings.

1. Press SET for 2 seconds until “FREQ” flashes on the display.
2. Press the SET button 5 times and “LOCK” will flash
3. Press (+) to LOCK or (-) UNLOCK
4. Press SET to store.

RECEIVER SETTINGS:

*To enter the settings menu press and hold the SET button.
To exit the menu select “9. Exit” with the (-) button and press SET.

FREQUENCY SETTING
Set the transmitter and the receiver to the same frequency.

1. Select “1. Frequency” with the (+) and (-) buttons and press the SET button.
2. Set the frequency with the (+) and (-) buttons. 3. Press the SET button to store the frequency.
   GROUP AND CHANNEL SETTING Once you set a frequency, you can store it as a channel, in a group. Each group can store 16 channel presets. Match these settings to the transmitter. 1. Select “2. Group/Channel” with the (+) and () buttons and press the SET button. 2. Press the (+) and (-) buttons to set the group to AB C, or D. 3. Press SET again to set the channel. 4. Press the (+) and (-) buttons to set the channel to 1-16. 5. Press SET to store the group and channel.

STEREO or MONO/MIX MODE SETTING
In Mono/Mix mode, both inputs are used, and the mix of the 2 inputs are adjusted on the receiver by using the Balance control.

1. Select “3. Stereo/Mono” with the (+) and (-) buttons and press the SET button.
2. Press (+) for Stereo or (-) for Mono/Mix mode.
3. Press SET to store.

HIGH FREQUENCY BOOSTER SETTING
The Hi Freq. Boost raises treble output to help hear detail in the mix. If the sound becomes distorted at high volumes, turn this feature OFF, or reduce the levels.

1. Select 4. Hi Freq Boost” with the (+) and (-) bunions and press the SET button.
2. Press (+) for boost ON or (-) for boost OFF.
3. Press SET to store.

LIMITER SETTING
The dynamic limiter reduces volume peaks to help protect your hearing.

1. Select “5. Limiter” with the (+) and (-) buttons and press the SET button.
2. Press (+) for limiter ON or (-) for limiter OFF.
3. Press SET to store.
   *To enter the settings menu press and hold the SET button.
   To exit the menu select “9. Exit” with the (-) button and press SET. 

LOCK SETTING
The Lock feature helps prevent accidental changing of settings.

1. Select 6. Key Lock” with the (+) and (-) buttons and press the SET button.
2. Press (+) for limiter ON or (-) for limiter OFF.
3. Press SET to store. TO RELEASE LOCK: Press SET, and then press (+)

LCD CONTRAST
Adjusting the Contrast setting will allow easier viewing in various lighting situations.

1. Select 7. Contrast” with the (+) and (-) buttons and press the SET button
2. Adjust the contrast with the (+) and (-) buttons.
3. Press SET to store.

BACKLIGHT TIME
To conserve battery life, the display backlight can be shut off at various time settings. Keeping the backlight ON will greatly reduce the battery life.

1. Select “8. Light time” with the (+) and (-) buttons and press the SET button.
2. Press (+) and (-) to select OFF, 1second, 2s, 5s, 10s, 20s, 30, or ON.
3. Press SET to store.

To exit the menu, select “9. Exit” and press SET.

ADVANCED SETUPS:

A. MULTIPLE MONITOR SYSTEMS
Up to 16 seperate EM900 transmitters can be used at on time, with unlimited EM901 receivers. For each monitor mix, set each pair of EMI00/EM901’s to a different frequency. Making use of the Group and Channel settings will make this setup easier.
B. MULTIPLE RECEIVERS
To use multiple receivers to monitor the same mix, simply set the receivers to the same frequency as the transmitter. Additional EM901 receivers are available from Carvin.
C. MULTIPLE TRANSMITTERS WITH SAME MIX
To connect multiple transmitters to the same source, connect 1/4” cables from the LOOP OUT connector of the first unit into the INPUTS of the second unit. This can be useful in areas with very unpredictable RF conditions to provide better coverage and for redundant backups.

SEE NEXT PAGE FOR DIAGRAMS OF ADVANCED SETUPS

A. MULTIPLE SYSTEMS
**B. MULTIPLE RECEIVERS

C. MULTIPLE TRANSMITTERS WITH THE SAME MIX**

MONITOR OUTPUTS FROM MIXER

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>