LG EVW011SK-SN Electric Vehicle Charger User Manual
- June 17, 2024
- LG
Table of Contents
User Manual
Electric Vehicle Charger
(Settings Guide)
EVW011SK-SN
EVW011SK-SR
After reading the user manual, store it in an accessible place for easy reference.
SYSTEM SETTING SCREEN
- Launch the Charger Settings app. (Compatible version: iOS 15 or above, Android 10 or above)
- When the password input window appears on the Charger Settings app, enter the set password. (The initial password is 000000, and you can change it through password change.)
- Go to the charger settings system screen.
| No. | Category | Descriptions |
|---|---|---|
| 1 | [Charger Connection and Disconnection] | This is the section for the Charger |
Settings app to connect to the charger.
1) Turn on the Bluetooth feature on your mobile phone, and click Find
Charger.
2) Press the Bluetooth Pairing button on the charger.
3) Connect to a charger that matches the model name and serial number among
the available chargers.
4) Connection successful pop-up will appear. Enter the password in the
charger password input window that is displayed when you close the pop-up.
(The initial password is 000000, and you can change it through password
change.)
5) You can check the information of the connected charger.
– [Model name]: Displays the model name of the charger.
– [Serial number]: Displays the unique number of the charger.
– [HMI Version]: Displays the version information of the charging application.
– [Control Board Version]: Displays the firmware version information of the
control board.
– [OCPP Software Version]: Displays the OCPP certification version
information.
6) Once the charger settings are complete, press Disconnect Charger to end
the connection with the charger.
NOTE
• The software version may change depending on the product’s performance
enhancement or function improvement in the future.
NOTE
• The software version may change depending on the product’s performance
enhancement or function improvement in the future.
• Bluetooth pairing button location
2| [Charger Settings]| When the charger settings app connects to the charger
via Bluetooth, it enters the settings screen.
• [Network]: Display the IP address information of the charger and set the
wireless network.
• [Basic Settings]: Set the URL of the charging control server (operation
server) and the ID of the charger.
• [Voice]: Set the volume and language for the charger.
• [Master Charger and Charging Capacity Settings]: Set up master charger
settings and the maximum charging capacity.
• [Change Charger Password]: Change the password set on the charger.
• [Reset Charger Data]: Reset the data stored on the charger.
3| [Network]| Display the currently assigned IP address of the charger and set
the wireless network.
• [Wi-Fi]: This is where you set the charger to use a wireless network. To set
the charger’s wireless network, enter the password of the AP router that the
smartphone with the Charger Settings app installed is connected to. 
NOTE
• The charger and the wireless Wi-Fi router should be located within 40 m
(131.2 feets).
Since the installation environment significantly affects wireless Wi-Fi
communication, this distance may be reduced.
• The number of chargers that can be connected to a Wi-Fi router can vary
depending on the performance of the Wi-Fi router.
4| [Basic Settings]| This is where you set the URL of the charging control
server (operation server address) that the charger needs to connect to and the
ID of the charger. Enter the operating server address and charger ID, then
press the [Continue] button.
5| [Voice]| • [Language]: Can be set in English, French, or Spanish.
• [Volume]: Adjust the volume of the charger. You can adjust from 0 to 10.
6| [Master Charger and Charging Capacity Settings]| Set whether a charger is a
master charger and its maximum charging capacity.
You must set only one of the chargers connected to the same local network as
the master charger.
You can select maximum charging capacity from 16 A / 24 A / 32 A / 40 A / 48
A.
7| [Change Charger Password]| Change the password set on the charger. 
8| [Reset Charger Data]| Reset the data stored in the charger, such as network
settings information, charging control server (operating server) address and
charger ID, voice settings information, and charger password.
9| [Load Management]| If set as the master charger, you can access the load
management menu.
• [Activate/Deactivate Load Management]: Activate/Deactivate load management.
• [Load Management Settings]: Set the load management information.
10| [Activate/Deactivate Load Management]| Activate or deactivate load
management according to the settings.
11| [Load Management Settings]| Upon entering the menu, the currently operating load management information is displayed. Press the [Settings] button to change the load management information.
• [Settings]: Select the chargers to include in load management from the displayed charger list and set the maximum load value to change the load management information.
Model………………..
Serial number…………………
Temporary noise is normal when powering ON or OFF this device.