Cobra CPP7510 Jum Pack Portable Jump Starter Power Pack User Manual
- June 17, 2024
- Cobra
Table of Contents
CPP7510 Jum Pack Portable Jump Starter Power Pack
User Manual
CPP7510 Jum Pack Portable Jump Starter Power Pack
Portable Power – Anytime, Anywhere!
Thank you for purchasing the Cobra CPP7510 JumPack portable jump starter
PowerPack. Before using this product, please read these instructions carefully
to learn about the features and capabilities of the JumPack and how to get the
best performance.
Note: Please charge your CPP7510 JumPack completely prior to using it for
the first time. ©2016 Cobra Electronics Corp. Part No. 480-1075-P Printed in
China Version A ™
The Cobra line of quality products includes:
- CB Radios
- Dash Cams
- Radar Detectors
- Marine VHF Radios
- Power Inverters
- Accessories
IMPORTANT SAFETY INSTRUCTIONS
Charge the JumPack fully prior to use.
Precautions when working with the JumPack:
WARNING: Keep the unit clear of fire and water.
WARNING: Shock Hazard. Keep away from children. Do not insert foreign
objects into the Jump Start Cable Input, the USB Output Port, or the Charge
Adapter Input Jack. Do not expose this product to water, rain, snow,
condensation, or spray. Do not open the JumPack to replace the internal
battery. No user replaceable parts are inside the JumPack.
WARNING: Explosion Hazard. Do not use this product where there are
flammable fumes or gases, such as an inadequately vented bilge of a boat, or
near propane tanks. Do not use this product in an enclosure containing
automotive-type lead-acid batteries.
The Jump Start Cable clamps must be connected positive to positive (red clamp
to battery [+]) and negative to negative (black clamp to battery [-]).
WARNING: Fire Hazard
Do not crush or puncture the JumPack. Never allow the Jump Start Cable’s red
and black clamps’ metal contacts to touch each other or another common metal
conductor. This could cause damage to the unit and/or create a fire hazard.
The jump start feature is designed only for starting vehicles, and Jump Start
Cables must be disconnected from the vehicle’s battery and from the JumPack
once the vehicle starts.
When jump starting a vehicle with the JumPack, turn the ignition key for no
more than 3 seconds at a time.
Caution: Operating temperature
Do not expose the JumPack to temperatures over +113° F (+45° C) or under -14°
F (-10° C). Using the JumPack at high or low temperatures may reduce the
internal battery capacity and shorten the battery life.
Note: In extreme cold weather conditions, please store the JumPack
indoors for best results.
The JumPack is supplied with a rechargeable Li-Cobalt battery.
This battery is self-contained and not consumer replaceable. Battery must be
disposed of properly when it no longer holds a charge. Proper charging
practices will increase the life of the batteries. For information on battery
recycling call toll free 800-822-8837.
Precautions when working with vehicle batteries:
WARNING: Explosion and fire hazard
- Follow all instructions published by the battery manufacturer and the manufacturer of the equipment in which the battery is installed.
- Make sure the area around the battery is well-ventilated.
- Never smoke or allow a spark or flame in the vicinity of the engine or batteries.
- Be careful not to drop a metal object on the battery or allow a metal tool to simultaneously touch the positive and negative cable ends or battery terminals.
- Remove personal metal items such as rings, bracelets, necklaces, and watches when working with batteries. Batteries produce a short-circuit current high enough to weld a ring or other similar objects to metal, causing a severe burn.
- If you need to remove a battery, always remove the negative terminal from the battery first. Make sure all accessories are off to prevent causing a spark.
- Someone should be within range of your voice, or close enough to come to your aid when you work near batteries.
- Have plenty of fresh water, soap and a supply of baking soda on hand in the area of the batteries in case of contact with battery acid. Baking soda neutralizes lead acid battery electrolyte.
Product:
Operation
Recharging the JumPack:
The CPP7510 JumPack can be recharged with the supplied Car Adapter or with the
supplied AC Adapter.
When the CPP7510 is charging, the light bar will show the current battery
charge level. The last section of the light bar that is lit will blink to show
that the JumPack is charging. When the JumPack is fully charged the light bar
will turn off automatically.
For best battery performance the JumPack should be fully recharged every 3
months.
Check Battery Charge
Level:
To check the battery charge level of the JumPack press the button on the top
of the unit with no device connected.
The green light bar will show the remaining battery charge level:
1st Section on:
10%-40% charge
2nd Section on: 40%-65% charge
3rd Section on: 65%-85% charge
4th Section on: 85%-100% charge
Note: When charging a device the section light may decrease because the
JumPack cannot accurately measure the capacity during rapid charging. To
confirm the actual battery charge level, disconnect the device being charged
and press the Flashlight/Battery Charge Level Button.
Checking the Fuse:
The Jump Start Cables are designed with an in-line fuse to protect the Jumpack
in the event of an over-load condition. The Jump Start Cables include a clear
case to that the in-line fuse is intact: 
CAUTION: Do not use the Jump Start Cables if the fuse
appears to opened or damaged. For any questions, please call
773-889-3087 for assistance or visit us
online at: www.cobra.com
Starting a Vehicle:
-
Make sure the JumPack is fully charged.
-
Turn off all the accessories on the vehicle.
-
Connect the RED clamp to the POSITIVE post of the battery.
-
Connect the BLACK clamp to the NEGATIVE post of the battery.
-
Connect the Jump Start Cable into the Jump Start Cable Input.
Be sure that the plug is firmly pressed into the JumPack. -
Turn the ignition key to start the vehicle. Do not crank the ignition for more than 3 SECONDS at a time.
-
If the vehicle does not start on the first try, WAIT FOR 1 MINUTE before trying to start the vehicle again.
NOTE: If your vehicle does not start after 3 attempts, consult with a mechanic.
If the engine starts: -
Immediately disconnect the Jump Start Cable from the JumPack, then from the battery posts.
-
Leave the engine running for at least twenty minutes to allow the vehicle’s battery to recharge.
Starting a Vehicle continued:
NOTES: The JumPack is designed for gasoline powered
passenger cars in good working order and with batteries that arenot damaged
but require assistance commonly due to leaving lights on, cold temperature, or
sitting unused for limited periodsof time.
The JumPack jump starter uses a special high current battery to provide up to
400 peak amps to start your engine. It can provide 200 amps starting current
to jump start up to 3 cars on one charge. After this, the unit must be
recharged.
The JumPack is intended to jump start a vehicle with a battery that is not
completely discharged.
Charging a 5V USB Device:
To charge a 5V USB device, connect the device’s cable to the JumPack’s USB
output.
The JumPack will turn on and start charging the device automatically. The
green light bar will indicate the device is charging.
Once the device reaches its charge capacity and ceases charging,the light bar
will turn off.
Product
Features:
LED Flashlight:
Press the Flashlight/Battery/Charge Level Button for 3 seconds to turn on the
LED flashlight. Press again to activate the strobe function. Press again to
activate the SOS function. Press again to turn Off.
- Lithium Cobalt rechargeable battery.
- 200 Amp Starting Current / 400 Amp Peak Current.
- 5V/3 Amp USB Output for rapid charging of portable devices.
- High Intensity work LED light, strobe and SOS .
- Rechargeable by car adapter, or 120 VAC Wall Adapter.
Product Specification:
| • Li-Cobalt rechargeable battery: | 11.1V/28Wh |
|---|---|
| • Size: | 5.03” x 2.87” x 0.98” (128mm x 73mm x 25mm) |
| • Weight: | 10.58 oz. (300g.) |
| • Recharge times: | car or home – 4 hours |
| • Starting/Peak Current: | 200 Amps/400 Amps |
| • USB Output: | 5V 3 Amps |
FCC Statement:
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limitsare
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/television technician for help.
WARNING: Any modifications made to this device that are not expressly
approved by party responsible for compliance could void the user’s authority
to operate this device. Cobra and the snake design are registered trademarks
of Cobra Electronics Corporation, USA.
Cobra Electronics Corporation™ is a trademark of Cobra Electronics
Corporation, USA.
PROPOSITION 65 WARNING: This product contains a chemical known to the
State of California to cause cancer and birth defects or other reproductive
harm.
Limited 1-Year Warranty:
For Products Purchased in the U.S.A.
Cobra Electronics Corporation warrants that its Cobra CPP7510 JumPack Charger,
and the component parts thereof, will be free of defects in workmanship and
materials for a period of one year from the date of first consumer purchase.
This warranty may be enforced by the first consumer purchaser, provided that
the product is utilized within the U.S.A.
Cobra will, without charge, repair or replace, at its option, defective
products or component parts within the warranty period upon delivery to the
Cobra Factory Service Department, accompanied by proof of the date of first
consumer purchase, such as a duplicated copy of a sales receipt. You must pay
any initial shipping charges required to ship the product for warranty
service, but the return charges will be at Cobra’s expense, if the product is
repaired, this warranty gives you specific rights, and you may also have other
rights which vary from state to state.
Exclusions: This limited warranty does not apply:
1. To any product damaged by accident.
2. In the event of misuse or abuse of the product, or as a result of
unauthorized alterations or repairs.
3. If the serial number has been altered, defaced or removed.
4. If the owner of the product resides outside the U.S.A.
All implied warranties, including warranties of merchantability and fitness
for a particular purpose are limited in duration to the length of this
warranty.
Cobra shall not be liable for any incidental, consequential or other damages;
including, without limitation, damages resulting from loss of use or cost of
installation.
Some states do not allow limitations on how long an implied warranty lasts
and/or do not allow the exclusion or limitation of incidental or consequential
damages, so the above limitations may not apply to you.
For Products Purchased Outside The U.S.A.
Please contact your local dealer for warranty information.
Product Service:
For any questions about operating or installing this new Cobra product, or
if parts are missing…PLEASE CALL COBRA FIRST…do not return this product to the
store. If this product should require factory service, please call Cobra
before sending the product. This will ensure the fastest turn-around time on
any repair.
If Cobra asks that the product be sent to its factory, the following must be
furnished to have the product serviced and returned:
- For Warranty Repair include some form of proof-of-purchase, such as a mechanical reproduction or carbon of a sales receipt. Make sure the date of purchase and product model number are clearly readable. If the originals are sent, they cannot be returned;
- Send the entire product;
- Enclose a description of what is happening with the product. Include a typed or clearly printed name and address of where the product is to be returned, with phone number (required for shipment);
- Pack product securely to prevent damage in transit. If possible, use the original packing material;
- Ship prepaid and insured by way of a traceable carrier such as United Parcel Service (UPS) or Priority Mail with delivery confirmation to avoid loss in transit to: Cobra Factory Service, Cobra Electronics Corporation, 6500 West Cortland Street, Chicago, Illinois 60707 U.S.A.;
- If the product is in warranty, upon receipt of the product it will either be repaired or exchanged depending on the model. Please allow approximately 3 – 4 weeks before contacting Cobra for status. If the product is out of warranty, a letter will automatically be sent with information as to the repair charge or replacement charge.
For any questions, please call 773-889-3087 for assistance or visit us online at: www.cobra.com
Customer Support & Trademarks:
Customer Support
Should there be any problems with this product or further information needed
on its features please visit www.cobra.com for support, frequently asked
questions, Declarations of Conformity, and the electronic manual.
Waste Electrical and Electronic Equipment Information
This product has required the extraction and use of natural resources for
its production. It may contain hazardous substances that could impact health
and the environment, if not properly disposed. In order to avoid the
dissemination of those substances in our environment and to diminish the
pressure on the natural resources, we encourage you to use the appropriate
take-back systems for product disposal. Those systems will reuse or recycle
most of the materials of the product you are disposing in a sound way.
The crossed out wheeled bin symbol informs you that the product should not be
disposed of along with municipal waste and invites you to use the appropriate
separate take-back systems for product disposal.
If you need more information on the collection, reuse and recycling systems,
please contact your local or regional waste administration. You may also
contact your supplier for more information on the environmental performances
of this product.
The product label is located on the bottom of the unit.
Trademark Statement
Cobra, JumPack and the snake design are proprietary trademarks of Cobra
Electronics Corporation, USA.
NOTES
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>