Current B00GFTSV24 Orbit Marine LED Instruction Manual

Current B00GFTSV24 Orbit Marine LED Instruction Manual

Safety Instructions & Warnings

IMPORTANT: Please refer to additional safety instructions and warnings on last page.

• Carefully examine light fixture, wires and all components before and after installation. Ensure there is no damage or water on any components BEFORE plugging into a GFCI wall outlet.

• NEVER plug in a wet cord. Always unplug with dry hands for any maintenance or service.

• Ensure 12VDC UL® power supply is plugged into a GFCI approved outlet with a drip loop for each light fixture. If using eFlux pumps, ensure a 24VDC UL® power supply is used with drip loop.
  Turn controller OFF and disconnect lights and pumps from power before performing service.

• Never look directly into the LEDs.

• Never run pumps dry or out of water.

• Follow all safety instructions for any wave pumps or additional add-on accessories.

• eFlux wave pumps create a tremendous amount of water flow. Do not install pump where the strong current can harm corals or animals.

• Pumps can also produce powerful waves in both wave and surge modes. Ensure your aquarium is designed for wave pumps and ensure pumps are mounted low enough not to push water out of the aquarium.

• Ensure light fixture is kept clean of any saltwater or salt creep. Fixture is IP65 rated for water splashing but must be kept clean of water, moisture, salt creep and/or any mineral deposits.

SAVE THESE INSTRUCTIONS

What’s Included

Additional Help

For additional installation instructions and videos, please visit our website at www.current-usa.com

What’s Included

Optional Accessories

Quick Start Guide

IMPORTANT: Before installing, read ALL SAFETY INSTRUCTIONS and WARNINGS
Step 1. Remove light and all components from packaging. Place light over aquarium using adjustable docking legs to ensure proper fit.
Step 2. Mount light HUB and LOOP controller next to each other in a dry location. Plug LOOP controller microUSB into Port#2 on light HUB.

Step 3. Connect Orbit Marine light fixture to Light#1 Connection plug “L1”. Plug 12VDC power supply into corresponding Light #1 DC input plug. Plug transformer into a GFCI protected outlet ensuring drip loop is in place (see safety warnings.)
Step 4. Connect IR infrared sensor to IC Light Manifold HUB into PORT #1. Locate sensor receiver in desired location.

Please visit www.current-usa.com for installation videos.

Installation Instructions

Step 8. Plug 12V DC power supply into GFCI outlet. Communication LED indicator light on manifold HUB will flash Blue.
Step 9. Use velcro cable wraps (L) for excess cables.
Step 10. Remove clear plastic tab from battery compartment on remote control (H).
Step 11. Press Main Power Key to turn Orbit Marine light ON. Light will operate in default setting.
Step 12. Follow programming guide on next page to program clock and light cycle.

IR Remote Overview

LOOP Light & Pump Controller Overview

Light Cycle Overview

Please review the following light cycle diagram:

Programming Guide

Programming Settings

Setting Current Time of Day

Programming Guide

On Demand Dynamic Modes

PUMP Programming

IMPORTANT WARNINGS I SAVE THESE INSTRUCTIONS
This is NOT a page of legalese. It contains important safety information that you should read and save for future reference.
Remember you can always quickly access instructions for all our products at www.current-usa.com.

• Never attempt repairs yourself; return the appliance to an authorized service facility for service or discard the appliance.
• Carefully examine the fixture after installation and BEFORE you plug it into the GFCI wall outlet. Be sure there is no water on any part of the light fixture or the timer.
• Never plug in a wet cord. If a plugged in unit or socket does get wet, DON’T touch it. Instead, promptly disconnect the fuse or circuit breaker that supplies power to the fixture. Then, you may unplug the fixture and examine for the presence of water.
• Never operate a fixture that is damaged or malfunctioning, discontinue use immediately and return the appliance to an authorized service facility.
• Close supervision is necessary when any appliance is used by or near children.
• Always unplug the fixture when not in use, before putting on or taking off parts, and before cleaning. Never pull the cord to unplug from the GFCI.

• Do not use the fixture for anything other than intended use. The use of attachments not recommended or sold by the fixture manufacturer may cause an unsafe condition and will void your warranty.
• Do not install or store the fixture where it will be exposed to the weather or to temperatures below 00 Celsius or 320 Fahrenheit.
• Do not operate at temperatures above 500 Celsius or 1220 Fahrenheit.
• Ensure the fixture is securely installed before supplying power to the unit.
• Read and observe all the important notices and warnings on the fixture and power cord. DO NOT REMOVE THE WARNING LABEL.
• If an extension cord is necessary, a cord with a rating at least 15 amperes should be used. A cord rated for less amperes or watts than the fixture rating may overheat. Care should be taken to arrange the cord so that it will not be tripped over or pulled.
• Do not look directly into the LEDs.

eFlux Pump Warning
• Do not install pumps where strong currents can harm animals. Do not install close to sand bed where it will suck/stir sand particles.
• Pumps can produce powerful wave action in both wave and surge modes. Ensure your aquarium is designed for wave pumps and ensure pumps are mounted low enough not to push water out of the aquarium.

Magnet mounting assembly is VERY powerful. Be cautious NOT to cause injury with fingers.
Keep magnets out of reach of children.
• Never place magnets or pump near sensitive electronics, sharp
• objects or other attractive surfaces.
• Never run eFlux water pumps dry or out of water
• Always place spacer between magnets when not in use.
• Always unplug with dry hands for maintenance or servicing.
• Always use a 24VDC or ETLTM power supply per pump.
• Turn controllers OFF and disconnect power before performing any service or maintence.

This product MUST be powered with a IJL@ or ETLTM power supply.

To avoid possible electric shock, power supply MUST be plugged into a GFCI wall outlet installed and grounded in accordance with all appropriate codes and ordinance. All products plugged into an AC power outlet or DC manifold MUST have a drip loop (see above.)

SAVE THESE INSTRUCTIONS.
Register this product at www.current-usa.com

Important Warnings I Drip Loops
Drip Loops should always be used to help prevent water from traveling along the cord and coming into contact with an electrical outlet. Drip loops must always be below the level of the outlet. If the plug or outlet does get wet, DO NOT TOUCH the cord. Disconnect the fuse or circuit breaker that supplies power to the system. After disconnecting the power, unplug and examine for the presence of water.

Current USA, Inc. One-year Limited Warranty
Current USA, Inc. ONLY warrants products purchased from authorized dealers. If your product was purchased through an unauthorized dealer, Current-USA, Inc. provides no warranty and any warranty claims MUST be done through your retailers. Current USA, Inc. warrants this product against defects in materials and workmanship of a period of ONE (1) YEAR from the date of original retail purchase and is not transferable.

Warranty on all Products, including Aquariums, is limited to replacement of the product and does not cover fish loss, personal injury, property loss or direct, incidental or consequential damage arising from the use of this product.

Note: Current-USA, Inc. One-year Limited Warranty does not cover damage caused by the following: improper installation, saltwater corrosion, electrical surges, or modifications.

If you discover a defect, please see your retail store or point of purchase. Current USA, Inc. will, at it’s option, repair or replace the product at no charge to you, provided you return it during the warranty period. A copy of the bill of sale is required as proof of original purchase date in the event the product needs repairs within  the warranty period. Please see your dealer for return options and warranty replacement parts. This warranty applies only to products by or for Current USA, Inc. that can be identified by trade name, or logo affixed to them. Current-USA, Inc. does not warrant any products that are not Current-USA, Inc..

This warranty does not apply if the product has been damaged by accident, abuse, misuse or misapplication or if the product has been modified without the written permission of Current-USA, Inc.; or if any Current-USA, Inc. logos have been removed or defaced.

THE WARRANTY AND REMEDIES SET FORTH ABOVE ARE EXCLUSIVE AND IN LIEU OF ALL OTHERS, WHETHER ORAL OR WRITTEN, EXPRESSED OR IMPLIED CURRENT USA, INC. SPECIFICALLY DISCLAIMS ANY AND ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO LOST PROFITS, DOWNTIME, GOODWILL, DAMAGE TO OR REPLACEMENT OF EQUIPMENT AND PROPERTY, AND ANY COSTS OF RECOVERING ANIMALS, PLANTS, TANKS OR OTHER AQUARIUM RELATED ITEMS AND/ OR EQUIPMENT. CURRENT USA, INC. IS NOT RESPONSIBLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES RESULTING FROM ANY BREACH OF WARRANTY, OR REPLACEMENT OF EQUIPMENT OR PROPERTY, OR ANY COSTS OF RECOVERING OR REPRODUCING ANY EQUIPMENT, ANIMALS OR PLANTS USED OR GROWN WITH CURRENT USA, INC. PRODUCTS. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or exclusions of  implied warranties, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights that vary from jurisdiction to jurisdiction.

Read More About This Manual & Download PDF:

References

• Manual-Hub.com - Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>