ERGOLUX ELSTD1MTMBA Standing Desk Electric Single Motor User Guide

ERGOLUX ELSTD1MTMBA Standing Desk Electric Single Motor

SAFETY & WARNINGS

• Read all instructions before use and retain this user guide for future reference.
• Read all the following safety precautions carefully before use.
• Your equipment is intended for use in cool, dry conditions. You should avoid storage in extremely cold, hot or damp areas as this may lead to corrosion and other related problems.
• This desk is designed for indoor use only.
• Do not modify the desk frame or any of the components that operate this desk in any way.
• If the power cord is damaged, cease use immediately and contact help.Kogan.com for support.
• If the control box emits any abnormal noises or strong odours, cease use immediately and contact help.Kogan.com for support.
• Ensure any obstacles are removed from the area around the desk during assembly and operation.
• Ensure that all cords and wires are arranged in a way where they are not a tripping hazard.
• Unplug the power cord before cleaning. Wipe the dust from the surface using a slightly damp cloth. Ensure any water does not come in contact with any internal parts or connectors.
• Do not disassemble or perform any maintenance without disconnecting the power first.
• Do not use any corrosive or abrasive materials to clean the product.
• The control box contains electronic components, metals, plastics, wires etc. Ensure it is disposed of in accordance with your local environmental legislation. Do not dispose of general household waste.
• Ensure this product is completely and correctly assembled before use.
• Be familiar with all functions and program settings of the product before first use.
• This product can be used by children aged 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved.
• Children should not be allowed to play with this product.
• Cleaning and user maintenance should not be performed by children without supervision.
• Retain the original packaging where possible, to use for any future transportation of this product.
• Power supply: AC100V-240V,50/60HZ
• Service Environment: 0-40°C
• Slight noise caused by the V-ribbed belt or brake system due to structure will not have any effect on the use of the equipment.

COMPONENTS

Lay all components out on a clean floor and ensure all parts are included. If any pieces are missing, check all packaging thoroughly, then contact help.Kogan.com for assistance.

Hardware List

OVERVIEW

1. Feet
2. Column
3. Column (with motor)
4. Supporting beam
5. Transmission rod
6. Supporting plate
7. Control panel
8. Baffle
9. Hand switch
10. Power cable
11. Cable tie

Control Panel

Adjust the desk upwards
Adjust the desk downwards

1. Position 1, the first height position saved by the user
2. Position 2, the second height position saved by the user
3. Position 3, the third height position saved by the user
4. Height memory function
5. Alert button to remind users to shift position

ASSEMBLY

Step 1: Install the feet

• Attach the Feet (1) to the bottom of the Lifting Column s (2 & 3) using x8 M6 Hex Screws (A).

Step 2: Install supporting beam

• Loosen screws on the supporting beam (4) using the 4mm Allen key (C) , then extend the supporting beam.
• Adjust the supporting beam size (4) according to your desktop size.

Step 3: Install supporting beam

• Attach the supporting beam to the lifting columns (2)(3) , using x2 M8 Hex Screw (B).
• Tighten screws on the supporting beam with a wrench 4mm Allen key (C).

Step 4: Install Transmission rod

• Loosen the nut on the left side of the Transmission rod (5) and insert it into the lifting column (2). Tighten the nut on the Transmission rod using the wrench (G).
• Rotate the right side of the Transmission rod (5) to insert it into the motor on the lifting column (3). Tighten the screw on the Transmission rod using the 2.5 mm Allen key (D). Note: Do not rotate the Transmission rod more than a third of a turn.

Step 5 : Install Supporting plate

• Use M8 Hex Screws (B) to attach the supporting plates (6) to the lifting columns (2)(3).
• Secure the supporting plates in place using the M6 Hex Screws (A).

Step 6 : Install Control box and Control panel

• Attach the desktop to the assembled frame using the ST4.2 screws (F) and a drill.
• Attach the control panel (9) to the front edge of the desktop using the ST4.2 screws (F) and a drill.
• Attach the control box (9) in the position shown below using the ST4.2 screws (F) and a dril

Step 7: Install Baffle

• Install the Baffles (8) , using x4 M4 Hex Screws (E) and the 2.5mm Allen key (D).

Step 8: Connect the Cables

• Connect the Cables to the Control Box (7).
• Use the cable tie (11) to manage all the cables underneath the desktop.

OPERATION

Adjusting the Height

Press the “▲” or “▼” buttons to adjust the height of the desk. The display will show the current height.

Memory Setting

• Press the”▲” or “▼” buttons to adjust the height to the desired height. Press “M” to save the height and the screen will display ” “ ; Press “ 1, 2 or 3 “. The height is now saved to the corresponding position. The saved position will show on the display screen as
• Press the “ 1, 2 or 3 ” button directly to automatically adjust the memory height you saved.

Stand Reminder

• Press the “A” button to activate the stand reminder function. The LED display shows “ “
• 2 seconds later, press the “▲” or “▼” button to adjust the reminder time only when the display screen flashes. The default time of the reminder is 45 minutes, which is shown as ” “.
• Press any button to save time or wait 5 seconds and the system will save the time automatically.
• During the countdown, any operation will lead to a repeat starting of the timer. When the countdown finishes, the display screen will show “ ” The buzzer will be active and beep for 10 seconds.
• Within the 10-second reminder, press any button to reactivate the countdown. If there is no user input within the 10-second reminder, there will be another alarm after 5 minutes.
• If there no user input during the second alarm, the stand reminder will turn off.
• Press and hold the “A” button for 3 seconds to turn off the stand reminder. The LED display shows “ “.

Collision Avoidance
During height adjustment, if the tabletop comes in contact with another object, it instantly stops and reverses to avoid damage.

• Press and hold the “▲” “▼” buttons for 5 seconds at the same time to adjust the collision avoidance sensitivity. Select between the 4 levels;

• Press and hold the “▲” “▼” button for 5 seconds at the same time. If the display does not display the above code, there is no anti-collision function.

Reset

• When the display shows “ “, press the “▼” button until the desk reaches its lowest height and rebounds to stop, it means the reset has been finished.
• If this fails and the LED shows “E01” or “E02”, wait 18 minutes before resetting the desk again.
• If the “▼” button doesn’t work, check the wiring and then disconnect the power for at least 10 seconds. Reconnect to the power and press “▼” button to start the reset process when it shows the display shows ” “

If the above procedure fails, contact help.Kogan.com for support.

SPECIFICATIONS

500-800mm

Duty Cycle| Continuous operation for 2 mins at most after pause for 18 mins
Applicable Temperature| 0~40°C

TROUBLESHOOTING

The following tips will help you detect and eliminate common faults. If the fault you met is not listed below, contact help.Kogan.com for support.

the cables are connected well
Contact help.Kogan.com for support.

The desk is rising very slowly.

| Ensure the desk is not overloaded. Max loading: 70kg;
The motor is not operating correctly.| Contact help.Kogan.com for support.

The desk will not raise or lower.

| Reposition the desk and ensure there are no obstructions.
Contact help.Kogan.com for support.

The desk slowly lowers itself.

| Ensure the desk is not overloaded. Max loading: 70kg;
Contact help.Kogan.com for support.
Contact your supplier or dealer
Overwork

(Duty cycle: Max 2min on/18min OFF).

| Restart after waiting for 18 minutes while connected with power.

The desk does not raise or lower enough.

|

Press “ M ” and “ 3 ” together for 3 seconds or more, after 2 beeps are heard. The desk has been restored to factory settings

This marking indicates that this appliance should not be disposed of with other household wastes. To prevent possible harm to the environment or human health from uncontrolled waste disposal, recycle it responsibly to promote the sustainable reuse of material resources.

Need more information?
We hope that this user guide has given you the assistance needed for a simple set-up. For the most up-to-date guide for your product, as well as any additional assistance you may require, head online to help.kogan.com

kugan.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>