ViewSonic VS19699 Enterprise Device Licensing Agreement User Guide

: June 17, 2024
: Viewsonic

Table of Contents

ViewSonic VS19699 Enterprise Device Licensing Agreement
Introduction
- Package Contents
Product Overview
Initial Setup
Making Connections
- Network Connection
- USB Connection
Using the Device
- Selecting an Input Source
Specifications
Regulatory and Service Information
- FCC Compliance Statement
Copyright Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

ViewSonic VS19699 Enterprise Device Licensing Agreement

ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-
product

IMPORTANT:
Please read this User Guide to obtain important information on installing and using your product safely, as well as registering your product for future service. Warranty information contained in this User Guide will describe your limited coverage from ViewSonic® Corporation, which is also found on our website at http://www.viewsonic.com in English, or in specific languages using the Regional selection box of our website.

Model No. VS19699
P/N: VPC-A31-O1

Thank you for choosing ViewSonic®
As a world-leading provider of visual solutions, ViewSonic® is dedicated to exceeding the world’s expectations for technological evolution, innovation, and simplicity. At ViewSonic®, we believe that our products have the potential to make a positive impact in the world, and we are confident that the ViewSonic® product you have chosen will serve you well.

Once again, thank you for choosing ViewSonic®!

Introduction

Package Contents

$ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $1$$

NOTE:
If anything is missing or damaged, please contact your local reseller for more information.

Product Overview

$ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $2$$ $ViewSonic-VS19699 -Enterprise-Device-Licensing-Agreement-fig- $3$$

Initial Setup

Installing the VPC-A31-O1

Remove the slot-in PC cover of the display. $ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $4$$
Using the handle of the VPC-A31-O1, carefully insert it into the PC slot of the display. $ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $5$$
Secure the VPC-A31-O1 to the display with the two (2) included screws.
NOTE: Please note that the three (3) antennas must be installed on the VPC- A31-O1.

Making Connections

Network Connection

To connect to the Internet or a network, connect one end of an RJ45 cable to the RJ45 port of the VPC-A31-O1, then connect the other end to your network.

$ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $6$$

USB Connection

USB peripherals such as keyboards, mice, storage devices, etc. can be connected to the VPC-A31-O1’s USB 1, USB 2, or USB 3 port.

$ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $7$$

Using the Device

Selecting an Input Source

IFP Series

$ViewSonic-VS19699-Enterprise-Device-Licensing-Agreement-fig- $8$$

To select an input source:

Press INPUT/ on the remote control, press the setting button on the front panel or press the Settings icon from the toolbar to display the Input Settings menu.
Press ▼/▲/◄/► on the remote control to select the PC source.
Press OK/ENTER on the remote control, or touch the input source directly.
Press EPG/BACK/ on the remote control, or touch a blank area outside of the menu to exit.
NOTE: The above image is for reference only and is subject to change without notice.

CDE Series

To select an input source:

Press INPUT/ on the remote control.
Press ▼/▲ on the remote control to select the PC source.
Press OK/ENTER on the remote control.
Press EPG/BACK/ on the remote control to exit.
NOTE: The above image is for reference only and is subject to change without notice.

IFPG1 Series
To select an input source:

Press INPUT/ on the front panel.
In the OSD Menu, touch INPUT.
Touch the PC input source directly.
Touch a blank area outside of the menu to exit.
NOTE: The above image is for reference only and is subject to change without notice.

Specifications

Category	Item	Specifications
Core	CPU	MediaTek MT8195
Graphic	Chipset	GPU: Mali G57 MC5 NPU: 4.8Tops
Memory	Memory	Slot type: LP-DDR4x Size: 8GB

I/O

| ****

Ports

| 1 x HDMI IN (v. 2.0, 4K@60Hz)

1 x HDMI OUT (v. 2.0, 4K@60Hz)

1 x RJ45 (LAN)

3 x USB 3.0 Type A

1 x USB 3.0 Type C (Data only, no PD support, 5V/900mA)

1 x Analog audio-in(3.5 mm, mic-in) 1 x Analog audio-out (3.5 mm)

3 x Antenna

Physical

Operating Conditions

| Altitude| < 5000 m
Humidity| 10% ~ 90% (non-condensing)
Temperature| 0°C ~ 40°C (32°F ~ 104°F)

Storage Conditions

Wi-Fi Module

| ****

Form Factor

| Wi-Fi 6 (IEEE 802.11 a/b/g/n/ac/ax Wi-Fi 2T/2R+)
---|---|---
Bluetooth 5.2 (V2.1/4.2/5.2 USB2.0/3.0 Module)

Frequency Range and Output Power (Max.)

| Typical RF Output Power at each RF chain, at a room temperature of 25°C (77°F)

2.4G

• 14±2dBm VHT20 at MCS0~7

• 13±2dBm VHT20 at MCS8~9

• 14±2dBm VHT40 at MCS0~7

• 13±2dBm VHT40 at MCS8~9

5G

• 14±2dBm VHT20 at MCS0~7

• 13±2dBm VHT20 at MCS8~9

• 14±2dBm VHT40 at MCS0~7

• 13±2dBm VHT40 at MCS8~9

• 13±2dBm VHT80 at MCS0~9

Regulatory and Service Information

Compliance Information
This section addresses all connected requirements and statements regarding regulations. Confirmed corresponding applications shall refer to nameplate labels and relevant markings on the unit.

FCC Compliance Statement

This device complies with part 15 of FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This equipment has been tested and found to comply with the limits for a Class B digital device, under part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and
can radiate radio frequency energy, and if not installed and used by the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and the receiver.
Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help.

Warning:
You are cautioned that changes or modifications not expressly approved by the party responsible for compliance could void your authority to operate the equipment.

Industry Canada Statement
CAN ICES-003(B) / NMB-003(B)

This Class B digital apparatus complies with Canadian ICES-003.

This device complies with Industry Canada licence-exempt RSS standard(s):
Operation is subject to the following two conditions: (1) this device may not cause interference, and (2) this device must accept any interference, including interference that may cause undesired operation of the device.

RESTRICTIONS IN THE 5 GHZ BAND
Within the 5.15 to 5.25 GHz band, UNII devices will be restricted to indoor operations to reduce any potential for harmful interference to co-channel Mobile Satellite System (MSS) operations.

This radio transmitter [4280A-VS19699] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum Permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Antenna info

Antenna type: External antenna
Manufacturer: Shenzhen Huadechang Technology Co., Ltd
Model name: HDC-300
Antenna gain: 5dBi
Connector type: RP-SMA (SMA Straight Plug Reverse for RG-178)

RF exposure
RF Radiation Exposure Statement Caution: This Transmitter must be installed to provide a separation distance of at least 20 cm from all persons.

CE Conformity for European Countries
The device complies with the EMC Directive 2014/30/EU, Low Voltage Directive 2014/35/EU and Radio Equipment Directive 2014/53/EU.

The following information is only for EU-member states:
The mark shown to the right complies with the Waste Electrical and Electronic Equipment Directive 2012/19/EU (WEEE). The mark indicates the requirement NOT to dispose of the equipment as unsorted municipal waste, but use the return and collection systems according to local law.

Declaration of RoHS2 Compliance
This product has been designed and manufactured in compliance with Directive 2011/65/EU of the European Parliament and the Council on the restriction of the use of certain hazardous substances in electrical and electronic equipment (RoHS2 Directive) and is deemed to comply with the maximum concentration values issued by the European Technical Adaptation Committee (TAC) as shown below:

Substance

| Proposed Maximum Concentration|

Actual Concentration

---|---|---
Lead (Pb)| 0.1%| < 0.1%
Mercury (Hg)| 0.1%| < 0.1%
Cadmium (Cd)| 0.01%| < 0.01%
Hexavalent Chromium (Cr6⁺)| 0.1%| < 0.1%
Polybrominated biphenyls (PBB)| 0.1%| < 0.1%
Polybrominated diphenyl ethers (PBDE)| 0.1%| < 0.1%
Bis(2-ethylhexyl) phthalate (DEHP)| 0.1%| < 0.1%
Butyl benzyl phthalate (BBP)| 0.1%| < 0.1%
Dibutyl phthalate (DBP)| 0.1%| < 0.1%
Diisobutyl phthalate (DIBP)| 0.1%| < 0.1%

Certain components of products as stated above are exempted under the Annex III of the RoHS2 Directives as noted below:

A copper alloy containing up to 4% lead by weight.
Lead in high melting temperature type solders (i.e. lead-based alloys containing 85% by weight or more lead).
Electrical and electronic components containing lead in a glass or ceramic other than dielectric ceramic in capacitors, e.g. piezoelectric devices, or in a glass or ceramic matrix compound.
Lead in dielectric ceramic in capacitors for a rated voltage of 125V AC or 250V DC or higher.

Indian Restriction of Hazardous Substances
Restriction on Hazardous Substances statement (India). This product complies with the “India E-waste Rule 2011” and prohibits the use of lead, mercury, hexavalent chromium, polybrominated biphenyls or polybrominated diphenyl ethers in concentrations exceeding 0.1 weight % and 0.01 weight % for cadmium, except for the exemptions set in Schedule 2 of the Rule.

Product Disposal at End of Product Life
ViewSonic® respects the environment and is committed to working and living green. Thank you for being part of Smarter, Greener Computing. Please visit the ViewSonic® website to learn more.

USA & Canada:
https://www.viewsonic.com/us/go-green-with-viewsonic.
Europe:
https://www.viewsonic.com/eu/go-green-with-viewsonic.
Taiwan:
https://recycle.epa.gov.tw/.

Copyright Information

Copyright© ViewSonic® Corporation, 2023. All rights reserved.
Macintosh and Power Macintosh are registered trademarks of Apple Inc.
Microsoft, Windows, and the Windows logo are registered trademarks of Microsoft Corporation in the United States and other countries.
ViewSonic®, the three birds logo, OnView, ViewMatch, and ViewMeter are registered trademarks of ViewSonic® Corporation.
VESA is a registered trademark of the Video Electronics Standards Association. DPMS, DisplayPort, and DDC are trademarks of VESA.
ENERGY STAR® is a registered trademark of the U.S. Environmental Protection Agency (EPA).
As an ENERGY STAR® partner, ViewSonic® Corporation has determined that this product meets the ENERGY STAR® guidelines for energy efficiency.

Disclaimer:
ViewSonic® Corporation shall not be liable for technical or editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from furnishing this material, or the performance or use of this product.

In the interest of continuing product improvement, ViewSonic® Corporation reserves the right to change product specifications without notice. Information in this document may change without notice.
No part of this document may be copied, reproduced, or transmitted by any means, for any purpose without prior written permission from ViewSonic® Corporation.

Customer Service
For technical support or product service, see the table below or contact your reseller.

NOTE: You will need the product’s serial number.

Country/Region

| Website| Country/Region|

Website