ZEPHYR DME-E48ASSX Mesa 48 Inch Wall Mount Range Hood with LED Lights Instruction Manual

ZEPHYR DME-E48ASSX Mesa 48 Inch Wall Mount Range Hood with LED Lights

Safety instructions

IMPORTANT SAFETY INSTRUCTIONS

• FOR RESIDENTIAL USE ONLY
• READ AND SAVE THESE INSTRUCTIONS
• PLEASE READ ENTIRE INSTRUCTIONS BEFORE PROCEEDING.
• IMPORTANT: Save these Instructions for the Local Electrical Inspectors use.
• INSTALLER: Please leave these Instructions with this unit for the owner.
• OWNER: Please retain these instructions for future reference.
• Take care when using cleaning agents or detergents.
• Suitable for use in household cooking areas.
• WARNING – To reduce the risk of fire or electric shock, do not use this fan with any Solid-State Speed Control Device.
• CAUTION – To reduce the risk of fire and to properly exhaust air, be sure to duct air outside – Do not vent exhaust air into spaces within walls or ceilings or into attics, crawl spaces, or garages.
• CAUTION – For general ventilating use only. Do not use to exhaust hazardous or explosive materials and vapors.
• CAUTION – To avoid motor bearing damage and noisy and/or unbalanced impellers, keep drywall spray, construction dust, etc. off the power unit.
• CAUTION – Please read the specification label on the product for further information and requirements.
• WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:
• A. Use this unit only in the manner intended by the manufacturer. If you have questions, contact the manufacturer.
• B. Before servicing or cleaning the unit, switch the power off at the service panel and lock the service disconnecting means to prevent power from being switched on accidentally.
• When the service disconnecting means cannot be locked, securely fasten a prominent warning device, such as a tag, to the service panel.
• C. To reduce the risk of fire, electric shock, or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).

WARNING – TO REDUCE THE RISK OF A RANGE TOP GREASE FIRE:

• A. Never leave surface units unattended at high settings. Boilovers cause smoking and greasy spillovers that may ignite. Heat oils slowly in low or medium settings.
• B. Always turn the hood ON when cooking at high heat or when flambeing foods ( i.e. Crepes Suzette, Cherries Jubilee, Peppercorn Beef Flambè ).
• C. Clean ventilating fans frequently. Grease should not be allowed to accumulate on the fan or filter.
• D. Use proper pan size. Always use cookware appropriate for the size of the surface element.
• E. Keep fan, filters, and grease-laden surface clean.
• F. Use high range setting on the range only when necessary. Heat oil slowly on low to medium setting.
• G. Don’t leave the range unattended when cooking.
• H. Always use cookware and utensils appropriate for the type and amount of food being prepared.
• WARNING – TO REDUCE THE RISK OF INJURY TO PERSONS IN THE EVENT OF A RANGE TOP GREASE FIRE, OBSERVE THE following:
• A. SMOTHER FLAMES with a close-fitting lid, cookie sheet, or metal tray, then turn off the burner. BE CAREFUL TO PREVENT BURNS.
• If the flames do not go out immediately, EVACUATE AND CALL THE FIRE DEPARTMENT.
• B. NEVER PICK UP A FLAMING PAN – You may be burned.
• C. DO NOT USE WATER, including wet dishcloths or towels – a violent steam ex-plosion will result.
• D. Use an extinguisher ONLY if:

1. You know you have a Class ABC extinguisher, and you already know how to operate it.
2. The fire is small and contained in the area where it started.
3. The fire department is being called.
4. You can fight the fire with your back to an exit Based on “Kitchen firesafety tips” published by NFPA

Proper maintenance of the Range Hood will ensure proper performance of the unit.

INSTALLATION INSTRUCTIONS

WARNING – TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS, OBSERVE THE FOLLOWING:

• A. Installation work and electrical wiring must be done by a qualified person(s) under all applicable codes and standards, including fire-rated construction.
• B. Sufficient air is needed for proper combustion and exhausting of gases through the flue (chimney) of fuel-burning equipment to prevent back drafting.
• Follow the heating equipment manufacturer’s guidelines and safety standards such as those published by the National Fire Protection.
• Association (NFPA), the American Society for Heating, Refrigeration and Air Conditioning Engineers (ASHRAE), and the local code authorities.
• C. When cutting or drilling into a wall or ceiling, do not damage electrical wiring and other hidden utilities.
• D. Ducted fans must always be vented to the outdoors.
• E. This unit must be grounded.

WARNING – TO REDUCE THE RISK OF FIRE, USE ONLY METAL DUCTWORK.
WARNING – UNDER CERTAIN CIRCUMSTANCES DOMESTIC APPLIANCES MAY BE DANGEROUS.

• A. Do not check filters with the hood working.
• B. Do not touch the lamps after a prolonged use of the appliance.
• C. No food must be cooked flambè underneath the hood.
• D. The use of an unprotected flame is dangerous for the filters and could cause fires.
• E. Watch constantly the fried food to avoid the cooking oil flares up.
• F. Before performing any maintenance operation, disconnect the hood from the electrical service.
• The manufacturers will not accept any responsibility for eventual damages, because of failure to observe the above instructions.

Electrical Requirements

Important:

• Observe all governing codes and ordinances.
• It is the customer’s responsibility to be aware of the below:
• To contact a qualified electrical installer.
• To assure that the electrical installation is adequate and in conformance with National Electrical Code, ANSI/NFPA 70 latest edition* or CSA standards C22.1-94, Canadian Electrical Code, Part 1 and C22.2 No.0-M91 – latest edition** and all local codes and ordinances.
• If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path is adequate.
• Do not ground to a gas pipe.
• Check with a qualified electrician if you are not sure the range hood is properly grounded.
• Do not have a fuse in the neutral or ground circuit.
• This appliance requires a 120V 60Hz electrical supply and is connected to an individual properly grounded branch circuit protected by a 15 or 20-ampere circuit breaker or time delay fuse.
• Wiring must be 2 wires with ground. Please also refer to the Electrical Diagram on the product.
• A cable locking connector (not supplied) might also be required by local codes. Check with local requirements, and purchase and install appropriate connectors if necessary.
• National Fire Protection Association Batterymarch Park, Quincy, Massachusetts 02269
• CSA International 8501 East Pleasant Valley Road, Cleveland, Ohio 44131-5575

Federal Communication Commission Interface Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, according to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used per the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

SAFETY PRECAUTION

1. Take care when the cooker hood is operating simultaneously with an open fireplace or burner that depends on the air in the environment and is supplied by other than electrical energy, as the cooker hood removes the air from the environment that a burner or fireplace needs for combustion. The negative pressure in the environment must not exceed 4Pa (4×10-5 bar).
   • Provide adequate ventilation in the environment for the safe operation of the cooker hood. Follow the local laws applicable to external air evacuation.
   • Before connecting the model to the electricity network:
   • Control the data plate (positioned inside the appliance) to ascertain that the voltage and power correspond to the network and the socket is suitable. If in doubt ask a qualified electrician.
   • If the power supply cable is damaged, it must be replaced with another cable or a special assembly, which may be obtained directly from the manufacturer or the Technical Assistance Centre.
2. Warning!
   • In certain circumstances, electrical appliances may be a dangerous hazard.
   • A) Do not check the status of the filters while the cooker hood is operating.
   • B) Do not touch bulbs or adjacent areas, during or straight after prolonged use of the lighting installation.
   • C) Flambè cooking is prohibited underneath the cooker hood.
   • D ) Avoid free flame, as it is damaging to the filters and a fire hazard.
   • E ) Constantly check food frying to avoid overheated oil may become a fire hazard.
   • F ) Disconnect the electrical plug before any maintenance.
   • G ) This appliance can be used by children aged 8 years and above and persons with reduced physical, sensory, or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning the use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be done by children without supervision.
   • H ) Young children should be supervised to ensure they do not play with the appliance.
   • I ) There shall be adequate ventilation in the room when the rangehood is used at the same time as appliances burning gas or other fuels.
   • L ) There is a risk of fire if cleaning is not carried out under the instructions.

INSTALLATION INSTRUCTIONS

• Assembly and electrical connections must be carried out by specialized personnel.
• Wear protective gloves before proceeding with the installation.
• WARNING Prop. 65 Warning for California Residents: This product may contain chemicals known to the State of California to cause cancer, birth defects, or other reproductive harm.

List of Materials

Ducting Calculation Sheet

Hood Specifications

Installation – Internal Blower

• NOTE! The device in this version (with an internal suction blower) is equipped for the rear discharge of exhaust air.
• However, if required, it is possible to have the exhaust air discharged from the top.
• This can be accomplished by carrying out the steps indicated in the following paragraphs; upon reaching step 8, the motor plate must not be rotated.
• The following instructions are for installing the internal blower.
• CAUTION: To reduce the risk of fire and electric shock, install this range only with internal blower models CBI-290C, CBI-390A, or CBI-600A.
• For external and in-line blower preparation please turn to.

1. Remove the (2) screws securing the top cover. See Fig.1
2. Remove the 6” round metal knockout plate from the blower plate by using a flathead screwdriver. See Fig.2
3. Remove the (6) screws securing the blower plate to the blower housing and remove the blower plate. See Fig.3
4. Install the internal blower into the blower plate and secure using (4) screws included with the blower. See Fig.4
5. Secure the capacitor box connected to the provided cable to the blower plate using (2) screws included with the blower. See Fig.5
6. Secure Green/Yellow ground wire connected to the cable to the provided capacitor to the blower plate. Fig.6
7. Attach the 6-pin male Molex connector from the blower wire to the 6-pin female Molex connector located inside the blower housing. See Fig.7
8. Install the blower and plate on the inside of the blower housing: carry out the instructions in step 2 in reverse order then use the screws provided to complete installation. (Tot. 12). Fig.8
9. Connect the 9-pin male Molex connector from the blower wire to the 9-pin female Molex connector on the capacitor wire. See Fig.9
   • WARNING! Place electrical wiring inside the blower housing.
10. Put the top cover back on.
    • The hood is now ready to be installed on the wall.

Installation – External & In-Line Blower Preparation

• NOTE! The device in this version (with an external blower) is equipped for the rear discharge of exhaust air. However, if required, it is possible to have the exhaust air discharged from the top.
• This can be accomplished by carrying out the steps indicated in the following paragraphs; upon reaching step 4, the blower plate must be rotated and installed in the opposite direction.
• The following instructions are for preparing the hood for use with an external or in-line blower model CBE-1000 or PBN-1000A.
• CAUTION: To reduce the risk of fire and electric shock, install this range only with remote blowers rated maximum of 6.2 A.
• For internal blower instructions please turn to.

1. Remove the (2) screws securing the top cover. See Fig.1
2. Remove the (6) screws securing the blower plate to the blower housing and remove the blower plate. See Fig.2
3. Remove the 8” round metal knockout plate from the blower plate by using a flathead screwdriver. See Fig.3
4. Install the plate with the outlet facing the wall, inside the motor casing: carry out the instructions at stage 2 in reverse order then use the screws provided to complete installation. (Tot. 12). See Fig.4
5. Install the flange and fix it to the blower plate with the (4) screws. Fig. 5
6. Put the top cover back on.
7. With the aid of a slotted screwdriver, break the grommet of a circular hole through which the wires pass. Fig. 6
8. Insert the female connector in the terminal box already attached to the hood. Fig. 7A
   • Pass the wires of the remote motor through the terminal box hole and connect them to the connector wires. Fig.7B
   • Note: Carry out the power supply connection per the national electric code, ANSI/NFPA 70-1999.
   • Note 1: A cable lock (not included) may be required by local codes. Please review local codes for more information.
9. Attach 6-pin male Molex connectors to 6-pin female Molex connectors inside the blower housing. See Fig. 8

• Note 2: Check local codes to determine the minimum wire gauge.
• See the manual included with the external and in-line blower for instructions on installing the blower.

Installation – Dual Internal Blower

(only for models : DME-E48ASGX, DME-E48AMBX, DME-E48ASSX)

Installation – Ducting Options

• WARNING FIRE HAZARD
• NEVER exhaust air or terminate duct work into spaces between walls, crawl spaces, ceilings, attics, or garages.
• All exhaust must be ducted to the outside unless using the recirculating option.
• Use single-wall rigid Metal ductwork only.
• Fasten all connections with sheet metal screws and tape all joints w/ certified Silver Tape or Duct Tape.

Some Ducting Options

Installation – Mounting the Range Hood

MOUNTING HEIGHTS

• The range hood must be installed at a minimum height of 24 inches (61cm) from the cooking surface. If a connecting duct work composed of two parts is used, the upper part must be placed outside the lower part.
• Do not connect the range hood duct to the same duct used to exhaust hot air or fumes from another appliance.
• Before proceeding with the assembly instructions remove the decorative mesh filters so that the range hood is easier to handle.

MOUNTING TO THE WALL

1. Place the paper template included with your hood on the wall to determine where to add the screws for mounting the hood. Make sure the bottom of the template aligns with the bottom of where the hood will be located. See Fig. 9
2. Lift the hood onto the screws and adjust it to make sure the hood is level.
3. When the hood has been adjusted tighten the screws to secure the hood in place.

• NOTE: Screws must be fastened into wooden studs so wood blocking may be necessary. If using wall anchors make sure to check your local codes for suitability and type of anchors to use.
• NOTE 1: For the various installations use screws and screw anchors suited to the type of wall (minimum screw size: 1/4″ diameter x 2-3/4″ length).

Installation – Power Supply Connection

GENERAL

• Carefully read the following important information regarding installation safety and maintenance.
• Keep this information booklet accessible for further consultations.

POWER SUPPLY CONNECTION

For connection to the power supply refer to the following:

• Remove the power supply cover by un-doing the (2) screws Fig. 1.
• Connect the wires of the hood to those of the power supply as described. Fig. 2 :
• BLACK = L line
• WHITE = N neutral
• GREEN / YELLOW = G ground
• A double-pole switch properly rated must be installed to provide the range hood po-wer supply disconnection.
• Connect the electrical conduit to the Field Wiring Compartment using listed conduit fittings.
• Carry out the power supply connection under the national electric code, ANSI/NFPA 70-1999.
• Insert the wires into the box, then close the box cover, securing it using the screws that were previously removed.

Installation – Safety Grille

• (only for models: DME-E48ASGX, DME-E48AMBX, DME-E48ASSX)

WARNING

• Safety Grille panel which must be installed.
• Remove the 10 screws already fixed in the appliance and use them to fix the Safety Grille panel as indicated in the figure below.

Touch Control

• A – Lights Button: Lights are three levels (high, medium, and low).
• From stand-by-on mode, touch once for high, twice for medium, three times for low, and four times to cycle back.
• B – Delay Off Button: Press the Delay Off Button to enable the ten-minute delay-off function, no matter at what speed the fan is running. B button will start blinking indicating the delay off function is enabled.
• After ten minutes the fan and lights will turn off.
• The delay-off function can be disabled by pressing the B button, changing the speed, or pressing the Power Button C.
• C – Power Button: Press once to activate all button stand-by mode allowing control of other button functions.
• All buttons will illuminate indicating stand-by mode. Press the Power Button again to turn the hood off (fan and lights). The standby mode will remain active for 30 seconds.
• D – Low-Speed Button: In stand-by mode: Press once for low speed.
• E – Medium Speed Button: In stand-by mode: Press once for medium speed.
• F – High-Speed Button: In stand-by mode: Press once for high speed.
• MESH FILTER CLEAN REMINDER (always enabled): after 60 hours of fan usage, button A blinks when the hood is on stand-by, indicating it is time to clean the mesh filters. To Reset the function: with the hood on stand-by, press and hold the B button for 4 to 5 seconds, the A button will stop blinking, and the 60-hour timer will reset.
• CHARCOAL FILTER REPLACE REMINDER (disabled by default, must be enabled by user if recirculating hood): To enable the Charcoal Filter Replacement Function hold buttons D and F simultaneously for four seconds. The A button will quickly flash 3 times indicating the Charcoal Filter Replacement Function is enabled. After 200 hours of fan usage, the B button will blink while the hood is on, indicating it is time to replace the charcoal filters. To Reset the Charcoal Filter Replace Reminder function: Hold the B button for 4 to 5 seconds until it stops flashing, and the 200-hour timer will reset.
• Order replacement charcoal filter kit number Z0F-C010 through your local dealer, www.zephyronline.com, or the Zephyr customer service department.
• To disable the Charcoal Filter Replacement function, repeat the enable procedure, the A button will illuminate for 3 seconds then turn off indicating the Charcoal Filter Replacement Function is disabled.
• CLEAN AIR FUNCTIOn (disabled by default, must be enabled by the user). To enable the Clean Air function, with the hood on standby, press and hold button E for 4 to 5 seconds.
• The E button will start blinking, the fan will turn on low speed for 10 minutes. After 10 minutes the fan will turn off and the 4-hour timer will begin. The E button LED will continue blinking when the Clean Air Function is enabled, even if the fan is not on.
• When the Clean Air function is enabled, every 4 hours of non-fan usage the fan will automatically turn on at low speed for 10 minutes. After 10 minutes the fan will turn off and the 4-hour timer will reset.

Maintenance

• It is recommended to operate the appliance before cooking. It is recommended to leave the appliance in operation for 5 minutes after cooking is completed to eliminate cooking vapors and odors.
• The proper function of the range hood is conditioned by the regularity of maintenance.
• The decorative mesh filters capture the grease particles suspended in the air and are therefore subject to clogging because of frequent use.
• To prevent a fire hazard, it is recommended to clean the filter a minimum of every 2 months or when instructed by the Metal Filter Clean indicator on the range hood controls.

Clean the range hood by carrying out the following instructions:

• Remove the filters from the range hood and wash them in a solution of water and neutral liquid detergent, leaving them to soak.
• Rinse thoroughly with warm water and leave to dry.
• Filters may also be washed in the dishwasher at the lowest setting.
• The filters may alter in color after several washes but are not cause for replacement.
• Clean the blower and other surfaces of the range hood regularly using a cloth moistened with denatured alcohol or nonabrasive liquid detergent.

Wiring Diagram

INTERNAL BLOWER CIRCUIT DIAGRAM

DUAL INTERNAL BLOWER CIRCUIT DIAGRAM

REMOTE BLOWER CIRCUIT DIAGRAM

List of Parts and Accessories

To order parts, visit us online at http://store.zephyronline.com

UL References

LED Light 1.3W (each)| SPK8148
Recirculating Kit| KIT0I0518
Replacement Charcoal Filters| ACK00061
Duct Cover Extension Inox| KIT0I0519
Duct Cover Extension MBlack| KIT0I0520
Duct Cover Extension Gold| KIT0I0521
Accent Rail Inox| KIT0I0631
Accent Rail Gold| KIT0I0630

Limited Warranty

TO OBTAIN SERVICE UNDER WARRANTY OR FOR ANY SERVICE-RELATED QUESTIONS:

• United States Customers please call: 1-888-880-8368 or contact us at: zephyronline.com/contact Canada Customers please call: 1-800-361-0799 or Email: service@distinctive-online.com
• Zephyr Ventilation, LLC (referred to herein as “we” or “us”) warrants to the original consumer purchaser (referred to herein as “you” or “your”) of Zephyr products (the “Products”) that such Products will be free from defects in materials or workmanship as follows:
• Two-Year Limited Warranty for Parts: For two years from the date of your original purchase of the Products, we will provide, free of charge, Products or parts (including LED light bulbs, if applicable) to replace those that failed due to manufacturing defects subject to the exclusions and limitations below. We may choose, in our sole discretion, to repair or replace parts before we elect to replace the Products.
• One-Year Limited Warranty for Labor: For one year from the date of your original purchase of the Products, we will provide, free of charge, the labor cost associated with repairing the Products or parts to replace those that failed due to manufacturing defects subject to the exclusions and limitations below. After the first year from the date of your original purchase, you are responsible for all labor costs associated with this warranty.
• Warranty Exclusions: This warranty covers only repair or replacement, at our option, of defective Products or parts and does not cover any other costs related to the Products including but not limited to: (a) normal maintenance and service required for the Products and consumable parts such as fluorescent, incandescent or halogen light bulbs, mesh and charcoal filters and fuses; (b) any Products or parts which have been subject to freight damage, misuse, negligence, accident, faulty installation or installation contrary to recommended installation instructions, improper maintenance or repair (other than by us); (c) commercial or government use of the Products or use otherwise inconsistent with its intended purpose; (d) natural wear of the finish of the Products or wear caused by improper maintenance, use of corrosive and abrasive cleaning products, pads, and oven cleaner products; (e) chips, dents or cracks caused by abuse or misuse of the Products; (f) service trips to your home to teach you how to use the Products; (g) damage to the Products caused by accident, fire, floods, acts of God; or (h) Custom installations or alterations that impact serviceability of the Products. If you are outside our service area, additional charges may apply for shipping costs for warranty repair at our designated service locations and for the travel cost to have a service technician come to your home to repair, remove, or reinstall the Products. After the first year from the date of your original purchase, you are also responsible for all labor costs associated with this warranty. All Products must be installed by a qualified professional installer to be eligible for warranty repairs or service.
• Limitations of Warranty. OUR OBLIGATION TO REPAIR OR REPLACE, AT OUR OPTION, SHALL BE YOUR SOLE AND EXCLUSIVE REMEDY UNDER THIS WARRANTY. WE SHALL NOT BE LIABLE FOR INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES ARISING OUT OF OR IN CONNECTION WITH THE USE OR PERFORMANCE OF THE PRODUCTS. THE EXPRESS WARRANTIES IN THE PRECEDING SECTION ARE EXCLUSIVE AND INSTEAD OF ALL OTHER EXPRESS WARRANTIES. WE HEREBY DISCLAIM AND EXCLUDE ALL OTHER EXPRESS WARRANTIES FOR THE PRODUCTS, AND DISCLAIM AND EXCLUDE ALL WARRANTIES IMPLIED BY LAW, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE.
• Some states or provinces do not allow limitations on the duration of an implied warranty or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. To the extent that applicable law prohibits the exclusion of implied warranties, the duration of any applicable implied warranty is limited to the same two-year and one-year periods described above if permitted by applicable law. Any oral or written description of the Products is for the sole purpose of identifying the Products and shall not be construed as an express warranty. Before using, implementing, or permitting the use of the Products, you shall determine the suitability of the Products for the intended use, and you shall assume all risk and liability whatsoever in connection with such determination. We reserve the right to use functionally equivalent refurbished or reconditioned parts or Products as warranty replacements or as part of warranty service. This warranty is not transferable from the original purchaser and only applies to the consumer residence where the Product was originally installed located in the United States and Canada. This warranty is not extended to resellers.
• To Obtain Service Under Limited Warranty: To qualify for warranty service, you must: (a) notify us at the address or telephone number stated below within 60 days of the discovery of the defect; (b) give the model number and serial number; and (c) describe the nature of any defect in the Product or part. At the time of the request for warranty service, you must present evidence of your proof of purchase and proof of the original purchase date. If we determine that the warranty exclusions listed above apply or if you fail to provide the necessary documentation to obtain service, you will be responsible for all shipping, travel, labor, and other costs related to the services.
• This warranty is not extended or restarted upon warranty repair or replacement.
• Please check our website for any additional Product information, www.zephyronline.com.
• Zephyr, 2277 Harbor Bay Parkway, Alameda, CA 94502
• JAN21.0401
• www.zephyronline.com

PRODUCT REGISTRATION

• Congratulations on your Zephyr range hood purchase!
• Please take a moment to register your new range hood at www.zephyronline.com/registration

IT’S IMPORTANT

• Prompt registration helps in more ways than one.
• Ensures warranty coverage should you need service.
• Ownership verification for insurance purposes.
• Notification of product changes or recalls.
• Zephyr Ventilation
• 2277 Harbor Bay Pkwy.
• Alameda, CA 94502
• 1.888.880.8368
• 3011000132505

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>