TROY-BILT TB304S Straight Shaft String Trimmer Instruction Manual
- June 4, 2024
- TROY-BILT
Table of Contents
NEED HELP?
CALL 1-800-828-5500
TB304S Straight Shaft String Trimmer
| Read the operator’s manual thoroughly before operating the unit. Follow all
warnings and safety instructions. This fast guide is intended as a reference
for users that have already read the operator’s manual and are familiar with
the necessary safety
precautions.
---|---
| ASSEMBLY
Insert the short tab (the one without a hole) on the mount bracket into the slot on the cutting head shield. Insert the bolt on the cutting head shield into the hole on the mount bracket.
| Place the washer and wing nut onto the bolt. Tighten the wing nut securely
| Remove the hanger cap from the attachment. If present, remove the gray
spacer from the coupler. Turn the knob counterclockwise to loosen the coupler.
| Align the release button with the guide recess. Push the attachment straight
into the
coupler until the release button snaps firmly into the primary hole. Turn the
knob clockwise to tighten the coupler.
| Push the handle down onto the upper shaft housing. Make sure the bolt hole
faces to the right.
Insert the bolt into the bolt hole.
Tighten the bolt with a flat-head screwdriver, but do not tighten the bolt
completely
| Move the handle to a comfortable location. Make sure the handle is
positioned beyond
the end of the safety label.
Tighten the bolt until the handle is secure.
| Push the strap up through the center slot in the buckle. Bend the strap over
and push it down through the lower slot in the buckle.
Put the shoulder strap over the operator’s head and onto the left shoulder.
| Unscrew the oil fill plug. Pour the entire container of oil into the oil
fill hole. Reinstall the oil fill plug.
NOTE: DO NOT overfill. Never add oil to the fuel tank. DO NOT mix oil
with gasoline.
| Slowly remove the fuel cap. Fill the fuel tank. Reinstall the fuel cap. Move
the unit at least 30 ft. (9.1 m) from the fuel container and the fueling site
before starting the engine.
NOTE: Use fresh unleaded gasoline (less than 30 days old).
ASSEMBLY TOOLS REQUIRED
• Flat-head screwdriver
| Read the operator’s manual thoroughly before operating the unit. Follow all
warnings and safety instructions. This fast guide is intended as a reference
for users that have already read the operator’s manual and are
familiar with the necessary safety precautions.
---|---
| STARTING
PRIME:
Slowly press and release the primer bulb 10 times, or until fuel is visible.
| PRIME:
Move the choke lever to Position 1.
| PRIME:
Crouch in the starting position.
| PRIME:
Press and hold the throttle lockout. Squeeze and hold the throttle control.
NOTE: Continue to SQUEEZE and HOLD the throttle lockout
and the throttle control for ALL further steps.
| PRIME:
Pull the starter rope with a controlled and steady motion 5 times.
DO NOT pull the starter rope more than 5 times.
| START:
Move the choke lever to Position 2.
| START:
Pull the starter rope with a controlled and steady motion 5 to 10 times to
start the engine. Allow the engine to warm up for 60 seconds.
| START:
Move the choke lever to Position 3.
Allow the engine to warm up for an additional 60 seconds. The unit may be used
during this time.
| Snap the clip onto the shoulder strap loop.
Adjust the shoulder strap to fit the operator. Pull the buckle up to loosen
the shoulder strap. Pull the strap down to tighten the shoulder strap.
DIDN’T START?
Repeat the starting instructions.
If the unit still fails to start, refer to the operator’s manual for
additional starting and troubleshooting information.
IMPORTANT: READ THE OPERATOR’S MANUAL THOROUGHLY AND FOLLOW THE SAFE OPERATION PRACTICES WHILE OPERATING THE UNIT.
778-19312 / 00
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>