Watt Stopper WD-170 Dimmable PIR Wall Switch Instruction Manual

WD-170 Dimmable PIR Wall Switch
Instruction Manual

WD-170 Dimmable PIR Wall Switch

Installation Instructions
WD-170 and WD-180
Dimmable PIR Wall Switch

SPECIFICATIONS

Voltage:
WD-170 . . . . . . . . . . . . . . . . . . . . 120VAC, 60Hz
WD-180 . . . . . . . . . . . . . . . . . . . . 277VAC, 60Hz
Load Rating:
@120VAC . 10–500W ballast or incandescent load
@277VAC. . . . . . . . . . . . . . 10–500W ballast load
Tungsten: . . . . . . . . . . . . . Dims incandescent lamps
Ballasts: . . . . . . . . . . . Use with Advance® Mark X™ or Philips Ecotone ®electronic dimming ballasts
(line voltage forward phase-cut dimming ballasts)
Dimmer Adjustment : . . . . . . . . . . . . . . 5%–100%
Time Delay Adjustment : . . . . . . . . 30 sec.–30 min.

SADJUSTMENTS

CAUTION
WHEN ADJUSTING THE TIME DELAY OR WHEN SWITCH IS UNSECURED,
YOU SHOULD TURN OFF POWER TO THE SWITCH AT THE CIRCUIT BREAKER.

To test and adjust the unit:

1. With a Philips screwdriver, turn time delay trumpet (see diagram) to minimum (all the way counterclockwise).

2. Temporarily secure the switch to the wall box.

3. Turn on power to the switch at circuit breaker and allow a one minute warm-up.
   Note: Whenever the main power is restored to the switch, such as when turning on the circuit breaker, the occupancy sensor charges and may take up to a minute to function properly.

4. Test the unit by pushing the Auto/Off button to the auto position to turn lights on. Leave the room and lights should go off after 30 seconds.

5. Adjust the time delay trumpet to desired setting, between 30 seconds to 30 minutes (clockwise increases time). For most applications, about 10 minutes is recommended.

6. Align wide holes on attached metal bracket with holes in wall box and secure switch with screws provided.

7. Install cover plate to switch assembly with provided screws.

8. Push the Auto/Off button to the auto position to turn lights on.

TROUBLESHOOTING

Lights will not turn on: (LED flashes with body motion)

1. Press the Auto/Off button to the auto position.
2. Check all wire connections.
3. For technical support call 1(800)879-8585.

Lights will not turn on: (LED does not flash)

1. Make sure the main circuit breaker is on.
   Note: Whenever the main power is restored to the switch, the occupancy sensor charges and may take up to one minute to function properly.

2. Check all wire connections.

3. For technical support call 1(800)879-8585.

Lights will not turn off:

1. Depending on the time delay setting, there can be up to a 30 minute time delay after the last occupancy motion is detected.
2. To test if unit is operating properly, set time delay to minimum and move out of the sensor’s view. Lights should turn off after 30 seconds.
3. For technical support call 1(800)879-8585.
   Sensing motion outside detection areas:
   • Opaque adhesive tape is included with the sensor and can be used to limit the detection areas. See “Masking the lens”.
   IMPORTANT: Rapid successive pressing of the Auto/Off button will cause a delay in proper function.

ORDERING INFORMATION

Add -W for White, -I for Ivory, -G for Gray, -B for Black, or -A for Almond to the catalog number.

• One ASP-211 is included with each sensor.

WARRANTY INFORMATION

The Watt Stopper® , Inc. warranties its products to be free of defects in materials and workmanship for a period of five years. There are no obligations or liabilities on the part of The Watt Stopper, Inc. for consequential damages arising  out of or in connection with the use or performance of this product or other indirect damages with respect to loss of property, revenue, or profit, or cost of removal, installation or reinstallation.

UNIT DESCRIPTION

The Watt Stopper’s WD-170 and WD-180 are dimmable passive infrared wall switches that turn lighting systems on and off based on occupancy in the controlled area. A dimming slider adjusts the light level from minimum to maximum.
The switches work with the Advance ® Mark X™ or Philips Ecotone ® electronic dimming ballasts (ballasts that have line voltage forward phase-cut dimming control). The WD-170 also works with incandescent fixtures.
The sensors feature a hard vandal resistant lens which allows them to be used in a wide range of applications, including public spaces.

OPERATION

The WD-170 and WD-180 sensors turn lights on when a person enters the controlled area. Lights turn on to the level set with the dimming slider. The dimming slider does not turn the lights off, it allows users to increase or decrease the  light level.
The lights remain on while the space is occupied. When the space is vacated and the adjustable time delay of 30 seconds to 30 minutes (set during installation) elapses, the lights turn off.
The lights can be manually turned off at any time by pressing the Auto/Off button.

COVERAGE PATTERNS

The WD-170 and WD-180 will cover up to 300 sq. ft. The recommended coverage for typical desktop activity is 150 sq ft. The sensor has a two-tiered, multi- cell viewing Fresnel lens with a 180° field of view.

Masking the lens
Opaque adhesive tape is supplied so that sections of the sensor’s view can be masked. This allows you to eliminate coverage in unwanted areas. Since masking removes bands of coverage, remember to take this into account when trouble- shooting coverage problems.

INSTALLATION

The WD-170 and WD-180 switches can be connected to single or multiple loads, up to 500 watts maximum.

CAUTION
TURN POWER OFF AT CIRCUIT BREAKER BEFORE WIRING SWITCHES.
ALWAYS FOLLOW PROPER PRECAUTIONS WHEN WORKING WITH OR NEAR HIGH VOLTAGE.

1. Make sure that power has been turned off at circuit breaker.
2. Connect leads to sensor with UL listed wire connectors (BLACK to line, GREEN to ground, RED to load).
3. Do not attach switch to wall box at this time. See “Adjustments”.

WARNING
THE GROUND MUST BE TIGHTLY SECURED OR THE SENSOR WILL NOT WORK!

The Watt Stopper®
Putting a Stop to Energy Waste®
2800 De La Cruz Boulevard, Santa Clara, CA 95050 USA
Technical Support: 1(800)879-8585 1(972)578-1699
86-0480-00 4/98
Call 800-879-8585 For Technical Support
https://manual-hub.com/

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>