Whistler Z-11RPLUS High Performance Laser Radar Detector User Guide
- June 17, 2024
- Whistler
Table of Contents
Whistler Z-11RPLUS High-Performance Laser Radar Detector
Specifications
- Model : Z-11R+/Z-11RS
- Dimensions : 24 x 18 x 20 cm
- Weight : 13 kg
- Bands Supported : Ka, X, K, P, C, L
Product Usage Instructions
Installation
- Bracket Release Button: Press this button to easily release the mounting bracket.
- Speaker: The speaker provides distinct audio warnings for X, K, and Ka band radar, safety warning system, laser, and VG-2.
- Mounting Bracket Location: The slot holds the mounting bracket firmly.
- Radar Antenna: The compact, high-efficiency antenna receives radar signals.
- Front Laser: The high-gain optical lens provides increased sensitivity and field of view for leading-edge laser detection.
- Rear Laser: An integrated optical waveguide provides superior detection of laser signals transmitted from behind.
- City Button: Press this button to reduce the annoyance of false alerts typically encountered in urban driving areas.
- Quiet Button: Pressing QUIET before a radar signal is detected engages Auto Quiet Mode which provides reduced tone sounds after the initial warning. Pressing QUIET during a radar encounter silences audio alerts while allowing visual alerts to keep you informed.
- Power / Volume Control: This button turns the unit on/off and adjusts the audio level.
- Dim / Dark Mode: This mode engages Dim/Dark modes.
- Menu Button: Press this button to enter the option select mode.
- Numeric Icon Display: The display combines an icon display with a 7-segment digital display that shows signal strength indication and band identification.
- Alert Periscopes: These provide an additional attention-getting visual alert.
- Rubber Bumper: This protects the unit from impacts and provides stability during installation.
Important Note for Installation
Ensure that no obstructions are blocking the radar and laser signals. Remove any metallic obstructions such as metallic sunscreens or mirrored sunscreens, as they can affect radar and laser signals, reducing critical warning time. Regular tinted glass does not affect reception. If you are unsure whether your windshield has an ElectriclearTM type coating, consult your dealeror refer to the user guide for more information.
Fuse Replacement
The lighter socket plug is equipped with a replaceable 2 amp, 3AG fuse located behind the silver tip. To replace the fuse, carefully unscrew the tip of the plug.
IMPORTANT : Unscrew slowly. The tip contains a spring that may fly out when disassembling. Insert the new fuse with the spring and screw on the tip. With use, the screw cap on the plug may loosen. Retighten it occasionally.
FAQ
- Q: How do I release the mounting bracket?
- A: Press the Bracket Release Button to easily release the mounting bracket.
- Q: What does the V icon indicate?
- A: The V icon indicates that the unit is receiving a VG-2 signal.
- Q: How can I reduce false alerts in city areas?
- A: Press the City Button to reduce the annoyance of false alerts typically encountered in urban driving areas.
- Q: What is the purpose of the Quiet Button?
- A: Pressing the Quiet Button before a radar signal is detected engages Auto Quiet Mode, which provides reduced tone sounds after the initial warning. Pressing the Quiet Button during a radar encounter silences audio alerts while allowing visual alerts to keep you informed.
- Q: How do I replace the fuse in the lighter socket plug?
- A: Carefully unscrew the tip of the plug to access the replaceable fuse. Insert the new fuse with the spring and screw on the tip. Retighten the screw cap occasionally.
WHISTLER FEATURES
-
Bracket Release Button – provides quick and easy release of the mounting bracket.
-
Speaker – provides distinct audio warnings for X, K, Ka band radar, safety warning system, laser and VG-2.
-
Mounting Bracket Location – slot holds mounting bracket firmly.
-
Radar Antenna – compact, high-efficiency antenna receives radar signals.
-
Front Laser – high gain optical lens provides increased sensitivity and field of view for leading-edge laser detection.
-
Rear Laser – an integrated optical waveguide provides superior detection of laser signals transmitted from behind.
-
City Button – reduces the annoyance of false alerts typically encountered in urban driving areas.
-
Quiet Button – pressing QUIET before a radar signal is detected engages Auto Quiet Mode which provides “reduced tone” sounds after the initial warning. Pressing QUIET during a radar encounter silences audio alerts, while allowing visual alerts to keep you informed.
-
Power / Volume Control – turns unit on/off and adjusts audio level.
-
Dim / Dark Mode – engages Dim/Dark modes.
-
Menu Button – enters option select mode. Numeric Icon Display – combines icon display with a 7-segment digital display that shows signal strength indication and band identification.
-
Icon Display – offers an easy-to-read display to indicate power, city mode, radar band identification, and signal strength.
-
Alert Periscopes – provide an additional attention-getting visual alert.
-
X-band Icon – indicates the unit is receiving a
X-band signal. -
K-band Icon – indicates the unit is receiving a
K-band signal. -
Ka-band Icon – indicates the unit is receiving a
Ka-band signal. -
V – indicates that the unit is receiving a VG-2 signal. Indicates that VG-2 is engaged.
-
P – indicates unit is in Highway mode.
-
C – indicates that the unit is operating in city mode.
-
Signal Strength Icon – indicates the strength of the signal being detected.
-
L – indicates that the unit is receiving a laser signal.
-
Power Jack – provides connection for the power cord.
-
VG-2/Laser Icon – indicates that the unit is receiving either VG2 or laser signal.
-
X/K -band Icon – shows the unit is receiving a X or K band signal.
INSTALLATION
Mounting Guidelines
- Mount the unit as low as possible near the centre of the windshield.
- Do not mount the unit behind wipers, ornaments, mirrored sunscreens, etc. These obstructions have metal surfaces which can affect radar and laser signals and reduce critical warning time. (Regular tinted glass does not affect reception.)
- Some windshields have an Instaclear™ or Electriclear™ type coating, which affects radar signals. Consult your dealer or the user guide to determine if your windshield has this coating.
- Avoid placing unit in direct contact with the wind shield.
- To reduce the possibility of theft, conceal the unit when not in use.
Windshield Mounting
- Install the two suction cups and rubber bumper onto the bracket by fitting them into their holes.
- Press the suction cups onto the windshield at the location you have chosen.
IMPORTANT : Make sure the unit is level.
Note : Some newer cars have a plastic safety coating on the inside of the
windshield. The windshield bracket may leave permanent marks on this type of
surface.
To find out if your vehicle has this type of windshield, check the user guide
or ask your dealer. We recommend that you do not leave the suction cup bracket
on the windshield in direct sunlight. If the detector is removed, this may
cause blistering of the dash in some vehicles.
Power Connection
- Plug the small end of the power cord into the unit’s power jack.
- Plug the large end into the vehicle’s cigarette lighter.
Fuse Replacement
The lighter socket plug is equipped with a replaceable 2 amp, 3AG fuse located behind the silver tip. To replace the fuse, carefully unscrew the top of the plug.
IMPORTANT : Unscrew slowly. The tip contains a spring that may fly out when disassembling. Insert the new fuse with the spring and screw on the tip. With use, the screw cap on the plug may loosen. Retighten it occasionally.
Power On Self Test & Volume
Each time your Whistler detector is turned on, an automatic self-test sequence
confirms that the speaker and visual displays are functional. To increase the
volume, continue turning thevolume knob.
Integrated Real Voice® (Z-15R+/Z-15RS Only)
When selected, Real Voice® will be used to articulate the following:
- Band Identification
- Safety Warning System messages
- Feature Selection
Voice OFF/ON is selected by holding quiet button for approximately 2 seconds. Voice ON will announce “caution”, Voice OFF will give a double beep.
Feature Engaged Confirmation
Each time a button is pressed, one beep confirms the feature is “on”, two beeps confirm feature “off”.
Self Test Mute
Press the Quiet button during the self-test sequence to cancel the Self-Test
audio. This will not affect radar/laser alerts. To restore the Self- Test
audio, press the Quiet button during the next Self-Test.
Setting Saver
Setting Saver stores your personalized settings so that when the detector is
turned off and then on again, you do not have to re-enter them.
Auto Quiet Mode
Pressing QUIET before a radar signal is detected provides an alternate alert pattern, consisting of several beeps (indicating X, K, Ka or Safety Warning System™) followed by reduced tone. The reduced tone will continue for as long as the detected signal is present or any new signal is detected within 20 seconds, becoming morerapid as the strength of the signal increases.
- Press Quiet (before a signal is detected) to engage Auto Quiet.
- Once the Auto Quiet mode is engaged, you may cancel the audio alarm by pressing Quiet.
- Press Quiet (when the unit is not alarming) to cancel Auto Quiet mode.
Quiet Mode
Quiet mode cancels audio during an alert and any new alert within 20 seconds.
After 20 seconds of no alerts, the audio is restored for any new alerts.
- Press Quiet to cancel the audio.
- Press Quiet a second time during an alert to restore the standard audio alert pattern;or turn the unit off, then on.
City/City 1/City 2 Mode
Whistler’s Three Stage City Mode is designed to reduce the annoyance of
automatic door openers, intrusion alarms and other devices that share
frequencies with police radar. Generally, X band is used for these devices.
- Press the City button to cancel Highway Mode and engage City Mode.
- Press the City button again to enter City 1 Mode
- Press the City button again to enter City 2 Mode
- Press the City button a fourth time to cancel City 2 Mode and return the unit to Highway Mode.
In City Mode, weak speed/safety warning system signals give an initial alarm
of two beeps and then remain quiet unless the signal becomes very strong.
When the signal strength increases, two additional beeps are provided. City 1
and City 2 Modes operate the same as Highway Mode, but in City 1 Mode, X band
requires a stronger signal to alert. InCity 2 Mode, X-band is not detected.
CAUTION : Some towns/small cities may still be using X-band radar. City
Mode does not change the audio alert for laser or VG-2.
Highway Mode
Highway mode provides full audio warnings any time radar (X, K, Ka, Safety
Warning System™) or laser signals are detected and is recommended for openroad
driving.
Field Disturbance Sensor Rejection (FDSR)
Traffic Flow Sensor Rejection (TFSR)
Recently many new products that operate on police radar frequencies have been
causing nuisance alerts to radar detectors. These radar-based sensors are
installed alongside the Highway and more recently on vehicles used as lane
change assist / blind spot detectors/collision avoidance systems. TFSR when
turned ON is designed to eliminate alerts from specific Traffic Flow sensors.
FDSR when turned ONis designed to identify all radar-based collision avoidance
systems that operate within the same band as police radar and provide a brief
less intrusive alert to keep you informed and aware. A signal strength
indicator will help determine your proximity to the source without the
continued annoyance of audio.
We suggest you turn FDSR ON if you are experiencing excessive random false alerts when behind select vehicles.
NOTE: TFSR and FDSR are ON by default and not selectable on the Z11R+/Z-11RS
Alert Periscopes
Whistler’s Alert Periscopes provide an added attention-getting visual alert.
The two extra LEDs flash on and off when the unit alarms to provide a unique
visual alert. This alert can be programmed through the Option Select Mode to
be: ON, OFF, or FLASHING during alerts.
Dim/Dark Mode
Dim/Dark Mode reduces the illumination of the display.
- Press and release the Dark button to reduce illumination to a dim setting
- Press and release the Dark button a second time to engage Dark Mode. The display illumination is further reduced.
Dim or Dark can be engaged during an alert. In Dark Mode, the display goes dark for as long as a signal is being detected and 20 seconds after, then the display returns to the dimmer setting.
- Press and release the Dark button a third time to restore the display to full illumination.
Engaging/Disengaging VG-2
See Option Select Mode to turn this feature on.
Vehicle Battery Saver Mode
The Vehicle Battery Saver Mode automatically shuts off your detector within 6
hours. The timer is reset if the detector is turned off, unplugged or any
button is pressed before the time has expired. The detector will alert you
with an audible and visual warning before it shuts off. During this warning,
you can momentarily reset the unit by pressing any button. This will reset the
timer. If the unit has automatically turned itself off, press any button to
turn the unit back on.
Stay Alert Feature (Z-15R+/Z-15RS Only)
The Stay Alert Feature is designed to test a driver’s
alertness. To engage (when the unit is not alarming):
- Press and hold the City button for approximately 2 seconds. Release button during or immediately after the alert is given.
The “H” or “C” will flash indicating Stay Alert is activated. Within 30-60
seconds, two beeps are sounded; to show alertness, the driver must press
either the City, Menu, or Quiet buttons within 3-5 seconds. If a button is
pressed within 3-5 seconds, the cycle is repeated.
If a button is not pressed within 3-5 seconds, an alarm sounds and the display
flashes all the LEDs.
- Press the Dark button to exit the Stay Alert feature.
WARNING!!! Stay Alert is NOT intended as a substitute for adequate rest. You should NOT operate a vehicle if you are drowsy. During extended periods of vehicle operation, you should take frequent breaks. Improper reliance on the Stay Alert feature may result in vehicle damage, personal injury or death.
LASER/RADAR ALERTS
Laser
Audio / Visual Alerts When a laser signal is detected, model Z-11R+/Z-11RS
display indicates alert by illuminating the “V/L” and scrolling the signal
strength indicators from right to left. Model Z-15R+/Z-15RS display indicates
an “L” on the display. The audio alert is continuous for a minimum of 3
seconds.
Laser Tips
If you are the targeted vehicle, a laser gun can often determine your speed
within a few seconds after you receive an alert. In this situation, there is
generally no time to safely adjust your speed. However, if you are travelling
near or behind the targeted vehicle and receive an alert, response time should
be sufficient.Any laser alert, regardless of duration, requires immediate
action!
Pulse Protection®
Pulse (or instant-on) radar is more difficult to detect than conventional
radar because it remains “off” until activated to measure the speed of a
targeted vehicle. When a pulse-type transmission is detected, your Whistler
detector sounds an urgent 3-second audio warning. Model Z-11R+/Z-11RS will
flash the alert strength indicators at their fastest rate; on model
Z-15R+/Z-15RS a “P” will be displayed. After the 3-second pulse alert, the
standard alert pattern continues for as long as the signal is present. It is
important to respond promptly to a pulse alert, since warning time may be
minimal.
Safety Warning System/Audio/Visual Alerts
When your Whistler detector detects a safety warning system, it provides a
distinctive audio tone and; Model Z-11R+/Z-11RS illuminates the first and last
alert LED; Model Z-15R+/Z-15RS display shows an “S.” and a decimal point when
a Safety warning system is detected.
NOTE : You will not be able to receive SWS™ alerts if transmitters are not located in your area.
VG-2 Detection Mode
The VG-2, also known as a “radar detector detector,” is a special receiver
used by police to detect signals radiated by a radar detector. See speed
monitoring section for more information on VG-2.
When the VG-2 signal is detected, the VG-2 alert is sounded. After 3 seconds, the audio is cancelled and the VG-2 indicator flashes at a slower rate. Every 30 seconds, the detector checks for a VG-2 signal. This cycle is repeated if the VG-2 signal is detected again. If no signal is detected, two beeps are provided indicating an“all clear” condition.
During the period a VG-2 signal is detected, a radar signal cannot be detected. However, because the VG-2 alert has confirmed that a patrol car is nearby, you are already aware of the potential for speed monitoring and can adjustyour speed accordingly. Laser detection is not affected while a VG-2 signal is detected.
POP™ MODE ALERTS
POP™ Mode Alerts
Because POP™ Mode radar utilizes the same K or Ka-band frequencies, POP™ Mode
Alerts will be displayed as regular radar alerts.
OPTION SELECT MODE
Option Select Mode
Press the Menu button to enter the Option Select Mode. Each press of the Menu
button changes to the next selectable feature. The Dark (D) button and the
Quiet (Q) button turns the feature ON/OFF or Blinking for example. A decimal
point on model Z-15R+/Z-15RS will indicate a feature is ON; Model
Z-11R+/Z-11RS will illuminate the “III” icon. When the feature is off these
indicators will not be shown. A button must be pressed within 20 seconds or
Option Select Mode will automatically be exited.
NOTE : To exit Option Select Mode press and hold the menu button.
Reset Features
All user features can be reset to factory settings.
Factory Reset
-
Unplug the Power Cord from the unit
-
Press and hold Quiet
-
Plug the Power Cord into the unit
(Power switch turned on) -
Wait for 2 beeps
-
Release the Quiet button
TROUBLESHOOTING GUIDE
The unit is now reset.
Factory Settings are:
• Highway Mode
• Dim/Dark Mode to full illumination of the display
• Auto Quiet Mode OFF
• VG-2 Detection Mode OFF
• Self Test Mute OFF
• Voice® English (Z-15R+/Z-15RS Only)
• Alert Periscope to Blink
• POP™ Mode OFF
• SWS™ OFF (Z-15R+/Z-15RS Only)
• TFSR OFF (Z-15R+/Z-15RS Only)
• FDSR OFF (Z-15+/Z-15RS Only)
Your Whistler detector is expertly engineered and designed to exact quality
standards to provide you with reliable, trouble-free operation. If your unit
has been correctly installed following the guidelines in this guide, but is
not operating optimally, please refer to the troubleshooting guide below.
PROBLEM : Unit does to turn on – check fuse in plug; replace if necessary
with a 2 amp, 3AG type. Make sure the lighter socket is clean.
No or low audio – cancel Auto Quiet Mode or City Mode. Check the audio level
setting.
PROBLEM : Unit alarms when the vehicle hits bumps. Check for loose
lighter sockets; tighten and clean. Check connections at both ends of power
cord. Substitute another cord to determine if the cord is defective. Return
the defective cord to the factory.
If difficulties occur that cannot be solved by information in this Troubleshooting Guide, please call Whistler Customer Service at 1-800-531-0004 or visit our FAQ page at www.whistlergroup.com before returning your unit for service.
Care & Maintenance
During the summer months, avoid prolonged exposure to direct sunlight by
removing your unit from the dash when your vehicle is parked for an extended
period of time. Do not spray water, cleaners, or polishes directly onto the
unit. The spray may penetrate through the openings and damage the unit. Also,
do not use any abrasive cleaners on the unit’s exterior.
ARE DETECTORS LEGAL?
In Most States YES!
Laser-radar detectors are legal in every state for automobiles and light
trucks (under 10,000 lbs.) except Virginia and Washington, D.C., which have
local regulations restricting the use of radar receivers in any vehicle.
The Federal Highway Administration (FHWA) passed a nationwide regulation,
effective January 1994, which prohibited radar and laser detector use in
vehicles over 10,000 lbs.
FCC Information
FCC ID : HSXWH23
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:
- this device may not cause harmful interference.
- this device must accept any interference received, including interference that may cause undesired operation.
IMPORTANT : FCC requirements state that changes or modifications not expressly approved by Whistler could void the user’s authority to operate the equipment.
SPEED MONITORING
Radar Facts
A radar gun operates by transmitting radio waves at certain frequencies which
reflect off objects and are then picked up by the radar gun’s receiving
section. When a radar beam reflects off a moving target, a measurable
frequency shift occurs. The radar unit converts this shift into miles per hour
to determine your vehicle’s speed. Currently, the FCC (Federal Communications
Commission) permits the operation of traffic radar guns at
X Band (10.500 – 10.550 GHz),
K Band (24.050 – 24.250 GHz), and Ka Band
(33.400 – 36.000 GHz).
NOTE : A radar detector will only alarm if an officer is transmitting on
any one of the above radar bands.
Laser Facts
It’s well documented that many radar guns cannot reliably provide the speed of
a targeted vehicle that is travelling in a group of vehicles. In contrast, a
laser gun can target a specific vehicle out of a line of traffic and determine
its speed. The advantage of laser over radar in terms of target identification
is the result of the laser gun’s narrow beam.
radar transmission can cover more than a four-lane highway at a distance of
1,000 feet, compared with a laser transmission which covers about 3 feet at
the same distance. For best protection, keep these points, listed on the
following section, in mind:
- Because the vehicle’s license plate or headlights are the laser gun’s primary targets, mounting the Whistler detector on the dashboard can improve laser detection at short range.
- Do not follow closely behind any vehicle. If you can’t see past a vehicle ahead of you, chances are your detector won’t either.
- The receiving range of laser signals will not be the same as radar signals. Laser guns are most often used at short range.
- Whistler Laser-Radar detectors receive all current laser guns which operate at a laser wavelength of 905 ± 50 nm including but not limited to the following:
- Ultra Lyte
- LTI 20 – 20
- LTI TruSpeed® S
- ro Laser™ I II III
- Laser Ally
- Laser Atlanta® Stealth Mode
Other Speed Detection Systems
Several techniques other than radar or laser are used to measure vehicle
speeds. When these methods are being used, no detector can provide a warning.
These techniques include:
- Pacing – A patrol car drives behind you and matches your driving speed.
- Vascular/Aircraft – The time it takes a vehicle to travel a known distance is measured.
Radar Detector Detectors (VG-2) Spectre
The Interceptor VG-2, or simply VG-2, is a microwave receiver used by police to detect signals radiated by the local oscillator of a radar detector. Because its purpose is to identify persons driving with radar detectors, the VG-2 is known as a “radar detector detector”. The VG-2 is a tool used by the police to identify radar detector-equipped vehicles. If caught, in a state where detectors are illegal drivers risk losing their radar detector and receiving a fine. In addition, instant-on radar is almost always used in combination with a VG-2, leaving unsuspecting motorists vulnerable to receiving two tickets—one potentially for speeding, the other for possession of a detector. Having a radar detector capable of detecting the VG-2 may alert you to the presence of a speed trap.
For more information on speed monitoring technologies, please visit our FAQ page on our website: www.whistlergroup.com
It is the responsibility of the individual radar detector operator to know and understand the laws in your area regarding the legality of the use of radar detectors.
NOTE : The newest tool Police have to detect radar detectors is called Spectre. Spectre can detect the majority of undetectable (VG-2) laser/radar detectors on the market.
WARRANTY INFORMATION
Consumer Warranty
This Whistler Laser/Radar detector is warranted to the original purchaser for
a period of two years from the date of original purchase against all defects
in materials and workmanship. This limited warranty is void if the unit is
abused, modified, or installed improperly, if the housing has been removed, or
if the serial number is missing. There are no express warranties covering this
product other than those set forth in this warranty. All express or implied
warranties for this product are limited to the above time. Whistler is not
liable for damages arising from the use, misuse, or operation of this product.
NOTE : Units that cannot be repaired will be replaced with the same or
similar model. Replacement unit’s warranty will be based on the original
unit’s purchase date.
Service Under Warranty
During the warranty period, defective units will be repaired without charge to
the purchaser when returned with a dated store receipt to the address below.
Units returned without a dated store receipt will be handled as described in
section
“ Service Out-Of-Warranty.”
Due to the specialized equipment necessary for testing a Laser-Radar receiver, there are no authorized service stations for Whistler brand detectors other than Whistler.
When returning a unit for service, please follow these instructions:
- Ship the unit in the original carton or in a suitable sturdy equivalent, fully insured, with return receipt requested to:
- Whistler Repair Dept.
- 1412 South 1st St.
- Rogers, AR. 72756
- Please allow 3 weeks turnaround time.
- IMPORTANT : Whistler will not assume responsibility for loss or damage incurred in shipping. Therefore, please ship your unit insured with return receipt requested. CODs will not be accepted!
- Include with your unit the following information, clearly printed:
- Your name and street address (for shipping via UPS), a daytime telephone number and an email address, if applicable.
- A detailed description of the problem (e.g., “Unit performs self-test but does not respond to radar”).
- A copy of your dated store receipt or bill of sale.
- Be certain your unit is returned with its serial number. For reference, please write your unit’s serial number in the space provided on the Accessory page of this guide
Units without serial numbers are not covered under warranty.
IMPORTANT : To validate that your unit is within the warranty period,
make sure you keep a copy of your dated store receipt. You may register your
warranty online at www.whistlergroup.com, however, for warranty verification
purposes, a copy of your dated store receipt must accompany any unit sent in
for warranty work.
Service Out-of-Warranty
Units will be repaired at “out-of-warranty” service rates when:
- The unit’s original warranty has expired.
- A dated store receipt is not supplied.
- The unit has been returned without its serial number.
- The unit has been abused, modified, installed improperly, or had its housing removed.
The minimum out-of-warranty service fee for your Whistler Z-11R+/Z-11RS detector is $35.00 (U.S.) and $40 (U.S.) for the Z-15R+/Z-15RS detector. If you require out-of-warranty service, please return your unit as outlined in the section “Service Under Warranty” along with a certified check or money order in the amount stated above. Payment may also be made by MasterCard, VISA or American Express; personal checks are not accepted.
In the event repairs cannot be covered by the minimum service fee, you will be contacted by a Whistler technical service specialist who will outline options available to you.
If you elect not to have your unit repaired, it will be returned to you along with your certified check or money order.
IMPORTANT : When returning your unit for service, be certain to include a
daytime telephone number and an email address (if applicable).
Customer Service
If you have questions concerning the operation of your Whistler detector or
require service during or after the warranty period, please call Customer
Service at:
- 1-800-531-0004
- Representatives are available to answer your questions Monday – Friday from 8:00 a.m. to 5:00 p.m. (CT).
- www.whistlergroup.com
SPECIFICATIONS
Laser Wavelength:
905 ± 50 nanometers (nm)
Radar Frequencies:
10.500 – 10.550 GHz (X Band)
24.050 – 24.250 GHz (K Band )
33.400 – 36.000 GHz (Ka Superwideband)
Operating Temperature Range:
-10º C to +70º C (+14º F to +158º F)
Power Requirements:
Operational 12 to 15 volts DC, 250mA nominal
Vehicle Battery Saver, 30mA nominal.
Patents can be viewed here:
- www.whistlergroup.com/pat
- POP™ Mode is a trademark of MPH Industries, Inc.
- SWS™ is a trademark of Safety Warning System L.C.
- Specifications are subject to change without notice.
ACCESSORIES
These and other accessories can be ordered directly from Whistler by calling 1-800-531-0004 or visiting our online store at www.whistlergroup.com.
- Modular: Interconnecting pieces cord and plug. Shipping and handling (per order) $5.00. Prices are subject to change without notice
Z-11R+/Z-11RS Z-15R+/Z-15RS HIGH-PERFORMANCE LASER-RADAR DETECTOR
- The Whistler Group Corporate Headquarters 1716 Commerce Dr. Ste. 8 Bentonville, AR 72712
- Tel: 479.273.6012
- Fax: 479.273.2927
Whistler Customer Return Center
- 1412 South 1st St
- Rogers, AR 72756
Customer Service
- Tel: 800.531.0004
www.whistlergroup.com
P/N 260037-1 06A16
© 2016 The Whistler Group, Inc.
Dear Whistler Customer,
If you have questions concerning the operation of
this Whistler product please call:
Customer Service
1-800-531-0004
Monday – Friday • 8:00 am – 5:00 pm CT or visit our website
www.whistlergroup.com
Please keep the receipt in a safe place. You may register your product online at www.whistlergroup.com. For warranty verification purposes, a copy of your dated store receipt must still accompany any unit sent in for warranty work. If the unit is returned without a dated store receipt, an out-of-warranty service charge applies. Note: Your warranty period begins at the time of purchase. The warranty is validated only by the dated store receipt! Please record the serial number of the unit in the space provided in the accessories section of the guide.
To fully acquaint yourself with the operation of your Whistler detector and to better understand the differences between detecting radar, laser, and safety radar signals, we recommend reading this entire guide or visiting our FAQ page on our website www.whistlergroup.com
Enjoy your Whistler detector and please drive safely.
Sincerely,
The Whistler Group, Inc.
References
- The Whistler Group, Inc
- The Whistler Group, Inc. Patents | Whistler Group
- Manual-Hub.com – Free PDF manuals!
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>