WAGNER FinishControl 5000 Airless Paint Spray System Instruction Manual

WAGNER FinishControl 5000 Airless Paint Spray System

EXPLANATION OF SYMBOLS USED

| This symbol indicates a potential danger for you or for the device.
Under this symbol you can find important information on how to avoid injuries and damage to the device.
---|---
| Indicates tips for use and other particularly useful information.
**| Wide spray jet setting
**| Narrow spray jet setting

SAFETY REGULATIONS

All local safety regulations in force must be observed.

Read the operating instructions carefully and follow the instructions laid down in them in order to avoid risks.

Safety at the workplace

• a) Keep your workplace clean and well lit. Disorder or unlit workplaces may result in accidents.
• b) Never use the tool in hazardous areas that contain flammable liquids, gases or dusts. Power tools generate sparks that can ignite the dust or vapors.
• c) Keep children and other persons away when using the power tool. You can lose control of the tool if you are distracted.

Electrical Safety

• a) The tool plug must fit into the socket. The plug may not be modified in any form. Do not use adaptor plugs together with protective-earthed tools. Unmodified plugs and suitable sockets reduce the risk of an electric shock.
• b) Avoid physical contact with earthed surfaces such as pipes, heating elements, stoves and refrigerators. The risk through electric shock increases if your body is earthed.
• c) Keep the equipment away from rain and moisture. The risk of an electric shock increases if water penetrates electrical equipment.
• d) Do not misuse the mains lead by carrying the tool by the lead, hanging it from the lead or by pulling on the lead to remove the plug. Keep the lead away from heat, oil, sharp edges or moving tool parts. Damaged or twisted leads increase the risk of an electric shock.
• e) If you work outdoors with a power tool, only use extension cables suitable for outdoor use. The use of an extension lead that is suitable for outdoors reduces the risk of an electric shock.
• f) If you cannot avoid using the tool in a damp environment, use a residual current operated circuit-breaker. Using a residual current operated circuit breaker avoids the risk of electric shock.

Safety of Persons

• a) Be attentive. Pay attention to what you are doing and work sensibly with a power tool. Do not use the tool if you are tired or under the influence of drugs, alcohol or medication. Just a moment of inattentiveness while using the tool can lead to serious injuries.
• b) Wear personal safety equipment and always wear safety goggles. Wearing personal protective equipment, such as dust mask, non-slip safety shoes, safety helmet or ear protection, depending on the type of power tools, reduces the risk of injury.
• c) Avoid accidental starting-up. Ensure that the switch is in the “OFF” position before inserting the plug into the socket. Accidents can occur if you carry the power tool while your finger is on the switch or if you connect the power tool to the power supply which it is on.
• d) Remove setting tools or wrenches before switching on the power tool. A tool or wrench that is in a rotating tool part can lead to injuries.
• e) Avoid an unnatural posture. This ensures that you can control the tool better in unexpected situations.
• f) Wear suitable clothing. Do not wear wide clothing or jewellery. Keep your hair, clothes and gloves away from moving parts. Loose clothing, jewellery or long hair can be caught in moving parts.
• g) This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

Careful Handling and Use of Power Tools

• a) Do not overload the tool. Use the power tool designed for the work that you are doing. You work better and safer in the specified performance range if you use the suitable power tool.
• b) Do not use power tools whose switch is defective. A power tool that cannot be switched on or off is dangerous and has to be repaired.
• c) Remove the plug from the socket before carrying out tool settings, changing accessories or putting the tool away. This precautionary measure prevents unintentional starting of the tool.
• d) Store unused power tools so that they are inaccessible to children. Do not let persons use the tool who are not familiar with it or who have not read these instructions. Power tools are dangerous when they are used by inexperienced persons.
• e) Take proper care of your tools. Check whether the moving parts function trouble-free and do not jam, whether parts are broken or damaged so that the tool function is impaired. Have damaged parts repaired before using the tool. Many accidents have their origin in power tools that have been maintained badly.
• f) Use the power tool, accessories, insert tools, etc. in accordance with these instructions and in a fashion specified for this special tool type. Take the working conditions and the activity to be carried out into consideration. The use of power tools for purposes other than the intended ones can lead to dangerous situations.

Service

• a) Have your tool repaired only by qualified specialist personnel and only with original spare parts. This ensures that the tool safety is maintained.
• b) If the supply cord is damaged, it must be replaced by the manufacturer or it’s service agent or a similarly qualified person in order to avoid a safety hazard.

Safety instructions for colour application devices

1. Risks of Fire and Explosion
   Combustible gases develop in the work area when spraying coating substances and due to the autonomous formation of coating substances and solvent vapors (danger zone).
   Risk of fire and explosion due to ignition sources in this danger zone.
   The electrically operated spray device contains potential ignition sources (spark formation when switching the motor on and off, when inserting and removing the power plug, due to potential static electricity at the spray gun)

   • Device must not be used at operating sites that fall under the explosion protection ordinance.
   • Basic unit and mains connection must be located outside the danger zone.
   • Do not use combustible coating substances and cleaning agents
   • observe product data sheets!
   • Always seal paint or solvent containers tightly in the vicinity of the device.
   • No ignition sources such as open fire, lit tobacco products, glowing wires, hot surfaces, sparks e.g. due to angle grinders etc. must be present.
   • When cleaning the device with solvent do not spray into a container with a small opening (bung hole). Danger due to formation of an explosive gas/air mixture.
     The container into which you are spraying must be earthed.

2. Warning: Danger of injury!
   Never point spray gun at yourself, other persons or animals.

3. Wear breathing equipment when spraying. The user should be supplied with a breathing mask. In order to avoid occupational diseases, the working instructions provided by the manufacturer of the materials, solvents and cleaning agents used must be complied with during preparation, working with and cleaning the equipment. Protective clothing, gloves and, if necessary, protective skin cream is required to protect the skin.

4. Warning: When working with the paint spraying system, both indoors and outdoors, care should be taken that no solvent vapours are driven to the motor-operated blower or that no solvent containing vapours form in the area around the paint spraying system. Place the motor-operated blower on the opposite side to the object to be sprayed. When working outdoors take wind direction into account. When working in closed places a sufficient ventilation must be ensured to remove the solvent vapours. The distance from the motor – operated blower to the object to be sprayed must be at least 3 m.

5. Warning: The device is not splash proof. It should not be used, neither outdoors in the rain nor be sprayed with water nor immersed in liquid. Do not use the device in damp or wet environments.

6. The units may only be used with a functional valve. If paints rises in the ventilating hose (Fig. 1, item 17) do not operate the unit further! Dismantle and clean the ventilating hose, valve and diaphragm and replace the diaphragm if necessary.

7. Do not lay the filled spray gun down.

8. Extraction systems should be installed on-site according to the local regulations.

9. The object to be coated must be earthed.

10. Caution against dangers that can arise from the sprayed substance and observe the text and information on the containers or the specifications given by the substance manufacturer.

11. Do not spray any liquid of unknown hazard potential.

12. Before dismounting the spray attachment, relieve pressure by opening the container.

13. Before working on the device, remove the power plug from the socket.

14. Work or repairs on the electrical equipment should only be carried out by a professional electrician, even if there are instructions regarding such work in the operating instructions. No liability will be accepted for improper installation.

15. Do not sit or stand on the device. Danger of tilting/ breaking!

EXPLANATORY DIAGRAM (FIG. 1)

POS. DESIGNATION

1. Nozzle
2. Air cap
3. Spray jet width adjusting lever (shaping air)
4. Spray jet level adjusting ring (vertical/horizontal)
5. Union nut
6. Spray attachment complete
7. Material volume regulation
8. Gun handle
9. Air volume control
10. Air hose
11. Click & Paint catch
12. Trigger (actuates turbine starting switch → material is conveyed)
13. Container
14. Suction tube
15. Container seal
16. Valve
17. Ventilating hose
18. Carry handle
19. ON/OFF switch (I = ON, 0 = OFF)
20. Gun mounting for park position
21. Air filter cover
22. Air filter
23. Power cable
24. Air hose connection
25. Cleaning brush
26. Fine feed tube filter (red) Coarse feed tube filter (white)
27. Funnel (3 pcs.)
28. Air hose fixing straps (2 pcs.)
    

THE WAGNER CLICK&PAINT SYSTEM

With the Wagner Click & Paint System, the front part of the gun (spray attachment) can be replaced quickly and easily. This enables a rapid material change without cleaning, and ensures that the right tool is available for every material and application

The following spray attachments are available:

and 1000 ml stainless steel container. Processes all standard paints.
Fine Spray (brown) Order No. 2321 877| Spray attachment with round nozzle and 1000 ml stainless steel container. Ideal for low-viscosity paints and glazes.
Walls pray (white) Order No. 2321 880| Interior wall paint spray attachment with slit nozzle and 1400 ml plastic container. Designed for processing acrylic paints.

DISASSEMBLY OF THE SPRAY GUN

For assembly, insert the spray attachment into the gun handle so that the two arrows point at each other. Turn the gun handle 90° in the arrow direction until it audibly engages. (Fig. 2)

To remove the spray attachment, push the catch (Fig. 2, A) beneath the trigger down and turn the spray attachment by 90°.

TECHNICAL DATA

4 dB (A)
Sound pressure output:* Uncertainty K:| 97 dB (A)
4 dB (A)
Oscillation level: Uncertainty K:| <2.5 m/s²
1.5 m/s²
Weight (motor-operated blower, air hose and spray gun):| 8 kg

The acoustic emission value was ascertained in accordance with EN 50144-2-7:2000

INTRODUCTION TO SPRAYING USING THE XVLP PROCEDURE

XVLP (Extra Volume Low Pressure) is a low pressure spraying technique, which works with a high volume of air and a low air pressure. The greatest advantage of this spraying technique is the low paint mist formation. This reduces the amount required to cover the object to a minimum. As opposed to conventional application of coatings, this method achieves a highly economical and perfect surface quality and is, at the same time, environmentally friendly.

Function description

The paint spraying system consists of a motor-operated turbo-blower, which provides the spray gun with atomization air through an air hose.
In the spray gun, a part of the atomization air is used to pressurize the container. This pressure causes the coating material to be fed through the uptake pipe to the nozzle where it is atomized by the rest of the atomization air.
All settings necessary for operation (e.g. material volume) can be conveniently made, directly on the gun.

COATING MATERIAL

COATING MATERIALS SUITABLE FOR USE

Solvent-based and water-soluble lacquer paints Mordants, glazes, stains, oils, clear varnishes, synthetic enamels, coloured paints, alkyd resin varnishes, primers, radiator paints, hammer effect enamels, anti-rust paints, special- effect paints, textured paints

COATING MATERIALS NOT SUITABLE FOR USE

Materials that contain highly abrasive components, façade paint, caustic solutions and acidic coating substances. Flammable materials.

COATING MATERIALS THAT CAN ONLY BE PROCESSED WITH RELEVANT SPRAY

ATTACHMENT (ACCESSORIES)

Wall Spray Attachment: Interior wall paint (acrylic paints)

PREPARING THE COATING MATERIAL

Observe the manufacturer’s instructions for the use of the coating material on the paint tin or on the technical instruction sheet.

Coating material purity:

An absolute pre-condition for the trouble-free operation of the fine-spray system is that the coating material is uncontaminated. If you have doubts as to the purity of the coating material, we recommend that you first filter it through a fine sieve.

Processing the coating material with the Fine Spray spray attachment (brown)

Spray spray attachment (white) recommended

SETTING THE SPRAY GUN

SETTING THE REQUIRED SPRAY PATTERN

Attention :
Never pull trigger while adjusting the air cap settings.

The alignment of the spray jet can be determined by turning the black adjusting ring (Fig. 3, 1).

• A horizontal flat jet → for vertical surfaces
• B vertical flat jet → for horizontal surfaces

It is also possible to switch between a wide (▷ ) and a compact (▻ ) spray jet with the adjusting lever ( Fig. 4, 1).

SETTING THE AMOUNT OF MATERIAL (FIG. 5)

The material volume can be adjusted incrementally from 1 (minimum) to 12 (maximum) by turning the material volume control (Fig. 5, 1).

SETTING THE AMOUNT OF AIR (FIG. 6)

Turn the air volume control (Fig, 6, 1) clockwise to increase the air volume or anti-clockwise to reduce the air volume (note arrow on body of gun).

 The correct setting of air and material volume is crucial for atomization and paint mist formation.

ALIGN THE FEED TUBE

If the feed tube is positioned correctly, the container contents can be sprayed without almost any residue.
When working on lying objects:
Turn the feed tube forwards. (Fig. 7 A)
Spraying work when working on overhead objects: Turn the feed tube rearwards. (Fig. 7 B)

STARTING OPERATION

Before connecting to the mains supply make sure that the mains voltage corresponds to the operating voltage on the rating plate. The unit must be connected with a properly earthed shockproof socket.

1. Squeeze the side clips together and insert the air hose onto the basic unit. (Fig. 8)
   

2. Unscrew the container from the spray attachment.

3. Pour in the prepared coating material.
   |

Fill the container with maximum 1000 ml.

---|---
4. Fit the appropriate filter to the feed tube depending on the coating material used (Fig. 9, 1)

Low-viscosity coating materials → Fine filter (red)
Viscous coating materials → Coarse filter (white)

5. Screw the container firmly onto the spray attachment.
6. Connect spray attachment and gun handle. (Fig. 2)
7. Plug in the power cable.
8. Switch on the main switch at the device.
   The device is now ready for operation.

SPRAYING TECHNIQUE

The Finish Control has a trigger with 2 pressure points. In the first stage the turbine is started. If the trigger is pressed further, the material is transported.

Operate trigger on the spray gun.
Test spray a piece of cardboard to ensure correct setting of the spray pattern, spray jet width, material and air volume.
Hold the paint spray gun upright and maintain a constant distance of about 3 – 20 cm to the object being sprayed. (Fig. 10)

Move the paint spray gun evenly either from side to side or up and down. If the gun is moved evenly, it will produce an even surface finish.
Always start spraying away from the object and avoid stop-ping spraying whilst still on the object.
In case of excessive paint mist formation, adjust the air and material flow respectively and alter the distance from the object.

BREAKS IN WORK

1. Switch device off with main switch on the basic unit.
2. Insert spray gun into gun mounting on the device.
    In using quick-drying or two-component coating materials, do not fail to rinse unit through with a suitable cleaning agent during the processing period.
   Important : The application life of the material can change as a result of heating. Therefore, please consult the material manufacturer.

TRANSPORTATION

1. Coil power cable around the basic unit.
2. Insert spray gun into gun mounting on the device.
3. Disconnect air hose by pressing the two side clips (Fig. 8).
4. Roll up the air hose and tie up with the fixing straps.

TAKING OUT OF OPERATION AND CLEANING

1. Turn the machine off.

2. Divide the spray gun. Press catch (Fig. 2, A) down slightly.
   Twist spray attachment and gun handle towards each other.
   ATTENTION! Electrical contacts in gun handle. Never hold the gun handle under water or immerse it into liquids.
   Clean the housing only with a moistened cloth.

3. Unscrew the container.
   Empty the remaining coating material into the original container.

4. Pre-clean the container and feed tube using a brush and suitable cleaning agent. Clean the ventilating bore. (Fig. 9, 2)

5. Pour solvent or water into the container. Screw the container back on.
   Do not use flammable materials for cleaning purposes.

6. Connect spray attachment and gun handle. (Fig. 2)

7. Switch device on and flush spray attachment through with solvent or water.
   Repeat the above procedure until the solvent or water emerging from the nozzle is clear.

8. Turn off the machine and divide the spray gun.

9. Screw off the container and empty it.
   Unscrew feed tube with container seal. (Fig. 11)
   

10. Clean feed tube and suction nozzle in spray attachment with cleaning brush. (Fig. 12)
    
    CAUTION! Never clean seals, diaphragm and nozzle or air holes of the spray gun with metal objects.
    The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe.

11. Remove the adjusting ring (fig. 13,1) carefully from the union nut (2). Unscrew union nut (2), remove air cap (3), nozzle (4) and nozzle seal (5). Thoroughly clean all parts.
    
     Take special care when cleaning the interstices on the needle (Fig. 14)
    

12. Clean the outside of the spray gun and container with a cloth soaked in solvent or water.

13. Assemble the parts again (see “Assembly”).

ASSEMBLY

ATTENTION! Follow the steps described below exactly for assembly. Otherwise the spray attachment may be damaged.

1. Push nozzle seal onto the needle so that the groove (slot) points away from the spray attachment. (Fig. 15)
   

2. Place nozzle on the needle with recess downwards. Attention if using Wall Spray or Standard Spray: Position of needle must be congruent with the nozzle aperture. (Fig. 16)
   

3. Place air cap on nozzle (pay attention to recesses in the air cap). (Fig. 17)
   

4. Screw on union nut. (Fig. 18)
   

5. Snap the adjusting ring into the union nut. (Fig. 19) Make sure that the two recesses on the adjusting ring are engaged in the air cap clamps and that the lever for  adjusting the spray jet width is located on the pin.
   

6. Place the container seal from below on the feed tube and slide it over the collar, while turning the container seal slightly.

7. Screw the feed tube with the container seal into the body of the gun.

 In order to mount the gun more easily apply lubricating grease (enclosed) liberally to the O-ring at the spray attachment and to the O-ring of the plug connection of the air hose (Fig. 20).

MAINTENANCE

AIR FILTER

Attention! Never operate the device with the air filter soiled or missing, as dirt could be sucked up and affect the operation of the device.
Always check the air filter before starting work.

1. Unplug the power plug.

2. Open the cover of the air filter compartment (Fig. 21).
   

3. Clean (blow out) or replace the air filter (Fig. 21,1) depending on the degree of soiling.

AIR RELIEF VALVE

 If paint has entered the ventilation hose, proceed as follows:

1. Pull the ventilating hose (Fig. 22, 1) at the top from the gun body. Screw off the valve cover (2). Remove the diaphragm (3). Clean all the parts carefully.
   
   CAUTION! The ventilation hose and diaphragm are only solvent-resistant to a limited extent. Do not immerse in solvent, only wipe.

2. Place the diaphragm in the valve cover with the pin facing forward (Also see the marking on the gun body).

3. Turn the body of the gun upside down and screw on the  valve cover from underneath.

4. Place the ventilating hose on the valve cover and on the nipple at the gun body

CORRECTION OF MALFUNCTIONS

• No mains voltage
• Device overheated

|

• Check
• Unplug the power plug, let the device cool down approx. 30 minutes, do not bend the hose, check the air filter, do not cover the intake slots

No coating material emerges from the nozzle|

• Nozzle clogged
• Material volume setting too low
• Paint container seal damaged
• No pressure build-up in container
• Container empty
• Ventilation hose loose/damaged
• Feed tube loose
• Feed tube / feed tube filter clogged
• Air vent on feed tube blocked
• Diaphragm stuck

|

• Clean
• Increase volume
• Replace
• Tighten container
• Refill
• Insert or replace
• Insert
• Clean or use another filter
• Clean
• Remove and clean (see section 13.2)

Coating material drips from the nozzle|

• Air cap, nozzle or needle soiled
• Spray attachment incorrectly assembled
• Nozzle loose
• Nozzle seal worn
• Nozzle worn
• Needle worn

|

• Clean
• Assemble correctly (see section 12.1)
• Tighten Union nut
• Change
• Change
• Use new spray attachment

Atomisation too coarse|

• Material volume too large
• Nozzle contaminated
• Viscosity of coating  trial too high
• Too little pressure build-up in container
• Air filter heavily soiled
• Amount of air too low
• Air hose damaged

|

• Reduce volume
• Clean
• Dilute further
• Tighten container
• Change (see section 13.1)
• Increase volume
• Check and replace if necessary

Spray jet pulsates|

• Coating material in container running out
• Nozzle seal worn
• Air filter heavily soiled
• Feed tube loose
• Feed tube / feed tube filter clogged

|

• Refill
• Replace
• Change (see section 13.1)
• Insert
• Clean or use another filter

Coating material causes “paint tears|

• Too much coating material applied
• Distance too small
• Incorrect spray attachment

|

• Reduce volume
• Increase distance
• Use another spray attachment

Excessive paint mist (overspray)|

• Distance to the object too large
• Too much coating material applied
• Amount of air too high
• Coating substance over-diluted
• Incorrect spray attachment

|

• Reduce distance
• Reduce volume
• Reduce volume
• Reduce degree of dilution
• Use another spray attachment

Paint in the ventilating hose|

• Diaphragm soiled
• Diaphragm defective

|

• Clean the diaphragm (see section 13.2)
• Replace the diaphragm (see section 13.2)

ACCESSORIES AND SPARE PARTS

ACCESSORIES

Processes all standard paints.
2| 2321 877| Fine Spray spray attachment (brown) (with 1000 ml container) Ideal for low-viscosity paints and glazes.
3| 2321 880| Wall Spray spray attachment (white) (with 1400 ml container) Designed for processing acrylics.
4| 2324 749| Container with cover (1400 ml)

SPARE PARTS FINISHCONTROL 5000 (FIG. 23)

SPARE PARTS FINESPRAY SPRAY ATTACHMENT (BROWN) (FIG. 24)

TESTING OF THE UNIT

For safety reasons, we would recommend having the device checked by an expert as required but at least every 12 months to ensure that it can continue to operate safely.
In the case of unused devices, the check can be postponed until they are next started up.
All (potentially deviating) national inspection and maintenance regulations must also be observed. If you have any questions, please contact the customer service team at Wagner.

IMPORTANT INFORMATION ON PRODUCT LIABILITY

An EU directive valid since 01.01.1990 specifies that the manufacturer is only liable for his products if all the parts originate from the manufacturer or are approved by him, and if the units are mounted and operated properly.
If accessories or spare parts from third parties are used, liability can be partially or completely inapplicable. In extreme cases the responsible authorities can prohibit the use of the entire unit (German industrial employer‘s liability insurance association and factory inspectorate).

With original WAGNER accessories and spare parts, compliance with all safety regulations is guaranteed.

NOTE ON DISPOSAL

 In observance of the European Directive 2002/96/EC on waste electrical and electronic equipment and implementation in  accordance with national law, this product is not to be disposed of together with household waste material but must be recycled in an environmentally friendly way!

GUARANTEE DECLARATION

Scope of guarantee

All Wagner professional colour application devices (hereafter referred to as products) are carefully inspected, tested and are subject to strict checks under Wagner quality assurance. Wagner exclusively issues extended guarantees to commercial or professional users (hereafter referred to as “customer”) who have purchased the product in an authorised specialist shop, and which relate to the products listed for that customer on the Internet under www.wagner- group.com/profi-guarantee.
The buyer’s claim for liability for defects from the purchase agreement with the seller as well as statutory rights are not impaired by this guarantee.
We provide a guarantee in that we decide whether to replace or repair the product or individual parts, or take the device back and reimburse the purchase price. The costs for materials and working hours are our responsibility. Replaced products or parts become our property.

Guarantee period and registration

The guarantee period amounts to 36 months. For industrial use or equal wear, such as shift operations in particular, or in the event of rentals it amounts to 12 months.
Systems driven by petrol or air are also guaranteed for a 12 month period.
The guarantee period begins with the day of delivery by the authorised specialist shop. The date on the original purchase document is authoritative.
For all products bought in authorised specialist shops from 01.02.2009 the guarantee period is extended to 24 months providing the buyer of these devices registers in accordance with the following conditions within 4 weeks of the day of delivery by the authorised specialist shop. Registration can be completed on the Internet under www.wagner-group.com/profi- guarantee.
The guarantee certificate is valid as confirmation, as is the original purchase document that carries the date of the purchase. Registration is only possible if the buyer is in agreement with having the data being stored that is entered during registration.
When services are carried out under guarantee the guarantee period for the product is neither extended nor renewed. Once the guarantee period has expired, claims made against the guarantee or from the guarantee can no longer be enforced.

Handling

If defects can be seen in the materials, processing or performance of the device during the guarantee period, guarantee claims must be made immediately, or at the latest within a period of 2 weeks.
The authorised specialist shop that delivered the device is entitled to accept guarantee claims. Guarantee claims may also be made to the service centres named in our operating instructions. The product has to be sent without charge or presented together with the original purchase document that includes details of the purchase date and the name of the product. In order to claim for an extension to the guarantee, the guarantee certificate must be included. The costs as well as the risk of loss or damage to the product in transit or by the centre that accepts the guarantee claims or who delivers the repaired product, are the responsibility of the customer.

Exclusion of guarantee

Guarantee claims cannot be considered

• for parts that are subject to wear and tear due to use or other natural wear and tear, as well as defects in the product that are a result of natural wear and tear, or wear and tear due to use. This includes in particular cables, valves, packaging, jets, cylinders, pistons, means-carrying housing components, filters, pipes, seals, rotors, stators, etc. Damage due to wear and tear that is caused in particular by sanded coating materials, such as dispersions, plaster, putty, adhesives, glazes, quartz foundation.
• in the event of errors in devices that are due to non-compliance with the operating instructions, unsuitable or unprofessional use, incorrect assembly and/or commissioning by the buyer or by a third party, or utilization other than is intended, abnormal ambient conditions, unsuitable coating materials, unsuitable operating conditions, operation with the incorrect mains voltage supply/frequency, over-operation or defective servicing or care and/or cleaning.
• for errors in the device that have been caused by using accessory parts, additional components or spare parts that are not original Wagner parts.
• for products to which modifications or additions have been carried out.
• for products where the serial number has been removed or is illegible
• for products to which attempts at repairs have been carried out by unauthorised persons.
• for products with slight deviations from the target properties, which are negligible with regard to the value and usability of the device.
• for products that have been partially or fully taken apart.

Additional regulations

The above guarantees apply exclusively to products that have been bought by authorised specialist shops in the EU, CIS, Australia and are used within the reference country.
If the check shows that the case is not a guarantee case, repairs are carried out at the expense of the buyer.
The above regulations manage the legal relationship to us concludingly. Additional claims, in particular for damages and losses of any type, which occur as a result of the product or its use, are excluded from the product liability act except with regard to the area of application.
Claims for liability for defects to the specialist trader remain unaffected.

J. Wagner GmbH
Division Professional Finishing
Otto Lilienthal Strasse 18
88677 Markdorf
Federal Republic of Germany

Subject to modifications

WAGNER WARRANTY POLICY

Our goods come with guarantees that cannot be excluded under the Australian Consumer Law.
You are entitled to a replacement or refund for a major failure and for compensation for any other reasonably foreseeable loss or damage. You are also entitled to have the goods repaired or replaced if the goods fail to be of acceptable quality and the failure does not amount to a major failure.

This warranty is provided by WAGNER and is in addition to your rights under the Australian Consumer Law.

WAGNER products come with a warranty, from the date of proof of purchase, against any manufacturing faults and defects. The
warranty periods are as follows:

DIY Products 24 months
Semi-Professional Products DIY use 24 months Semi-Professional use 12 months
Contractor and Commercial Products 36 months
Plats Coat Units 24 months
Hire and Rental Us e 6 months

Where replacement goods are supplied, the warranty is limited to the term of the original purchase.
Warranty applies only to the original purchaser and is not transferable.

This warranty does not cover products which are damaged as a result of any of the following:

• Unsuitable or abnormal usage
• Incorrect commissioning or fitting, removal or modification of any safety devices
• Repairs which are performed by unqualified or unauthorised persons, or do not involve genuine WAGNER parts
• Normal wear and tear
• Damaged in transport
• Faulty maintenance work, negligent handling, servicing or cleaning
• Unsuitable coating materials

To claim the warranty (Australia and New Zealand only) you should send or take your product (at your cost), with proof of purchase to one of the Authorised WAGNER Service Centres listed on the back of this Warranty. If found to be a warrantable claim, WAGNER, through its Authorised Service Agents will either repair or replace the product at its option free of charge and advise you when your replacement or repaired product is available for pick up by you.
Under this express Warranty Policy WAGNER is not liable for any loss or damage however arising as a result of the fault or defect in the products.
This express Warranty is subject to the purchaser providing satisfactory proof of purchase within Australia or New Zealand of the product to WAGNER or its Authorised Service Centres.
WAGNER reserves the right to perform any repairs in excess of those stated in our operating instructions.

Please note: This Warranty Policy and Procedure supersedes all other warranty policies, procedures and documentation for products sold within Australia and New Zealand.

AUSTRALIAN CUSTOMERS

Please send or take your product to any one of the Authorised WAGNER Service Centres listed on the reverse of this form.

NEW ZEALAND CUSTOMERS

Contact the Master Distributor listed below for your nearest Authorised Service Centre:
Paintworx, 70 Lady Ruby Drive, East Tamaki NZ 1730 Telephone: (09) 271 2879

NEW SOUTH WALES

Bathurst| David Catt Spray Repair| 02 6332 3269
Coffs Harbour| Brycker Hire| 02 6652 1829
Forster| Flashback Repairs| 02 6555 7202
Georgetown| Daynatech| 02 4960 9400
Gladesville| Colussi Engineering| 02 9817 5433
Gosford West| Gosford Power Tool Centre| 02 4325 5322
Grafton South| Beadman Engineering| 02 6642 3047
Lake Cathie| Coastal Spray| 02 6585 4735
Lismore South| Paint & Trade Supplies| 02 6622 1147
Milperra| Murphy’s Spray & Blast| 02 9792 2653
Moorebank| Spray Equipment Mobile| 02 9822 4011
Moruya| Moruya Mower & Chainsaw| 02 4474 3322
Penrith| Penrith Paint Specialists| 02 4731 1178
Tamworth| Tamworth Paint Centre| 02 6762 0520
Wagga Wagga| Simpson Machinery Service| 02 6928 1353
Woollongong| Frank Dean Airless Repairs| 02 4296 2989
NORTHERN TERRITORY

Holtze| Palmerston Paint Supplies| 08 8932 7999
QUEENSLAND

Acacia Ridge| Phyllo Industries| 07 3711 9589
Burpengary| Gleecrafts| 07 3888 0866
Cairns| Cairns Wholesale Paint| 07 4035 2000
Gladstone| Earle’s Paint & Wallpaper| 07 4972 3277
Kingaroy| Earle’s Paint & Wallpaper| 07 4162 5011
Maroochydore| Suncoast Pressure Cleaners| 07 5443 1139
Meadowbrook| Logan Pro Spray| 07 3803 4276
Maryborough| Earle’s Paint & Wallpaper| 07 4121 5202
Milton| Paint Place Superstore| 07 3369 7206
Morrie| Access Industrial Products| 07 3390 8199
Narang| W.A.S.| 07 5596 7255
Noosa Ville| Paint Place Noosa| 07 5449 9964
SOUTH AUSTRALIA

Mount Gambier| Attiwills Home & Industry| 08 8725 6644
Lonsdale| MWA| 08 8294 6444
Wingfield| Oliver Technologies| 08 8262 2466
VICTORIA

Bairnsdale| Bristol Decorator Centre| 03 5153 1177
Bairnsdale| Murphy’s World of Colour| 03 5152 4148
Ballarat| Bylsma Hire| 03 5335 8397
Bayswater| Spray links| 03 9720 1710
Campbellfield| Dete Australia| 03 9359 6080
Dandenong Sth| Paint Spot| 03 9793 4599
Eltham| Paint Place| 03 9439 4900
Geelong Nth| Kerr’s North Side| 03 5278 6011
Hastings| Dewtech| 03 5979 1617
Oakleigh| Sprayworld| 03 9041 4473
Sebastopol| Bylsma Hire| 03 5335 8397
Shepparton| Shepparton Paint Centre| 03 5831 2522
Shepparton| A1 Electric Motors| 03 5831 7066
Wantirna South| Morgan’s Paint Spot| 03 9801 8011
Warrnambool| Chemblast Industrial Coatings| 03 5562 7636
TASMANIA

Derwent Park| Paintech| 03 6273 2755
Invermay| Forward Mechanical Repairs| 04 1736 5627
WESTERN AUSTRALIA

Bassendean| Eden Systems| 08 9379 3588
Welsh pool| All Spray| 08 9358 1313
NEW ZEALAND

Contact Paintwork for nearest Service Centre| 64 9 272 2840

CUSTOMER SUPPORT

Wagner Spraytech Australia
14-16 Kevlar Close, Braeside, Victoria, 3195.
Customer Service 1800 924 637
Email: info@wagneraustralia.com.au
www.wagneraustralia.com.au

References

• Manual-Hub.com - Free PDF manuals!
• WAGNER 3+2 Professional Guarantee | Product registration
• Wagner Australia - A Faster Way to a Better Finish
• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>