Fosgoit 2.4GHz 4WD Gesture Sensing RC Stunt Car Toys Instructions

Fosgoit 2.4GHz 4WD Gesture Sensing RC Stunt Car Toys

REMOTE-CONTROL VEHICLE

REMOTE CONTROL

REMOTE CONTROL VEHICLE BATTERY INSTALLATION AND BATTERY CHARGE

1. To protect the battery pack within the vehicle, do not give the battery pack a charge immediately after usage.
2. Leave the battery pack for a few minutes before charging.
3. When charging, the USB charger indicator light is on, and when fully charged, the light turns off. The charging time is approximately 2-3 hours.
4. It is normal for the battery pack to become warm during charging.

REMOTE CONTROL BATTERY INSTALLATION\

Uses 2×1.5V “AAA” non rechargeable batteries. Please install the battery correctly according to the polarity indication (Battery not included).

GRAVITY SENSOR WATCH

1. One light illuminating indicates normal operation mode.
2. Press once quickly to enter the  auto-demo mode; continue holding to enter deformation mode.
3. Press quickly again, two lights flash and initiate the transverse drift mode.
4. Press again to illuminate three lights and start the 360-degree rotation mode.
5. Press and hold to enter dancing mode; press again to turn off the light and gesture sensing. Press a third time to turn off the sound effects. Repeat the cycle.

The battery charged in the toy must be regularly checked to prevent damage to wires and other parts. If damaged, it must be repaired before use. The toy can only used after everthing has been fully repaired or replaced.

BATTERY ATTENTION

1. This product is designed for remote control vehicles, using a 3.7V rechargeable lithium battery. The remote controller requires two 1.5V AAA non-rechargeable batteries.
2. The battery should be removed and loaded according to the polarity and voltage markings on the toy battery compartment; ensure not to short-circuit the battery.
3. Non-rechargeable batteries must not be charged.
4. The rechargeable battery should only be charged under adult supervision.
5. Rechargeable batteries must be cool to the touch before charging.
6. Do not mix different types of batteries or combine new and old batteries.
7. Only batteries of the same or equivalent type as the one recommended should be used.
8. Remove the exhausted battery from the toy if it’s not going to be used for an extended period.
9. Do not short-circuit the power supply terminals.
10. Do not connect to more power supplies than recommended.

AUTOMATIC CODE MATCHING

1. When the battery is installed in the remote control and the remote control vehicle, the indicator lights on both devices will start to flash, signifying the initiation of the connection process. Once the connection is established, the remote control vehicle’s switch is turned on, and the connection state is activated.
2. Each remote controller can only be paired with one remote control vehicle at a time. Multiple connections to several vehicles will interfere with the system (i.e., multiple vehicles cannot be connected simultaneously).
3. If, after one minute, the remote controller did not find the 2.4G signal from the vehicle, turn off both devices and restart the pairing process to ensure a connection is made.
4. When it is necessary to pair multiple models of remote control or remote vehicle, it is vital to turn off the power supply of remote control and remote vehicle before pairing to avoid signal interference.

REMOTE CONTROL OPERATION
Switch on the remote control and then the remote control vehicle. Ensure the power supply of the remote control car is sufficient to sustain the control distance.

CONTROL INSTRUCTIONS OF REMOTE-CONTROL VEHICLE

GESTURE SOMATOSENSORY CONTROLLED

GENERAL TROUBLESHOOTING

In the process of using the USB cable for the toy, check regularly to ensure the wires, plug, shell, and other parts are not damaged. If damaged, stop using the toy until it is repaired.

1. Keep the toy away from fire and avoid exposure to direct sunlight, high temperatures, and humidity. Do not leave it in a car for extended periods.
2. When not in use, remove the batteries from the remote control and vehicle. Store the remote control and the vehicle back in their box to prevent damage or deformation during transportation or storage.
3. Clean the remote control car gently with a slightly damp cloth.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>