teamson home 201601PTB 33 Inch 4 Tier Cascading Bowl Stone Fountain Brown User Manual

teamson home 201601PTB 33 Inch 4 Tier Cascading Bowl Stone Fountain Brown

Product Information

Specifications

• Dimensions: 5 ft / 1.52 m (maximum dimension)
• Water Level: Approximately 1 in / 25 mm below the top of the opening at the back of the basin

Product Usage Instructions

Assembly

1. Unpack the contents of the box.
2. Assemble the fountain on a surface that will not be damaged by water.

Fountain Setup

3. Place the pump upright into the basin and draw the pump power cord out through the opening at the back of the fountain.
4. Place each of the mesh screens inside the appropriate bowl, based on size.
5. Add clean water to the lowest bowl (basin) of the fountain. The water level should be approximately 1 in / 25 mm below the top of the opening at the back of the basin where the water circulates from.

Power Connection

6. Connect the pump to a GFCI outlet and the product will begin to function as intended.

Water Flow Adjustment

6. If the water flow is higher or lower than desired, adjust the regulator dial/slide on the front of the pump. (+) to increase the water flow or (-) to decrease the water flow.

LED Lights Replacement

7. The LED lights are preassembled, but they are replaceable. When replacing them, please refer to Steps 1 and 2.

Fountain Maintenance

8. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing after the initial setup of your fountain. It is highly recommended to place the fountain in an area where it cannot cause damage due to excessive splashing.
9. Do not leave your fountain running for extended periods when no one is present to observe the performance.
10. Check the area around your fountain regularly to ensure that there is no leakage.

Additional Information

Pump Cautions

• To reduce the risk of electric shock, this pump is equipped with a grounding conductor and grounding-type attachment plug.
• Be certain that it is connected only to a properly grounded, grounding-type receptacle. Use only portable self-contained fountains no larger than 5 ft / 1.52 m in any dimension.
• If equipped with a 3-prong, grounded-type plug, do not remove the grounding pin from the plug on the power cord.

Water

• Distilled water is always recommended to fill your fountain, or filtered water if distilled is not an option. (Tap water may contain minerals and chemicals that may build up and leave a residue.)

Cleaning Frequency

1. Regular cleaning of your fountain and pump will depend on where it is located. When the fountain or pump is visibly soiled, or there is a decrease in performance, please follow the care and maintenance tips below. Failure to clean and maintain the pump will result in overheating.
2. Keep the fountain water and pump clean and clear of debris. Remove any leaves or other debris every other day.
3. Clean your fountain monthly to prevent mineral buildup and contamination, which may clog the pump. (This frequency may vary depending on where your fountain is located.)
4. Water treatments that prevent algae growth and mineral deposits and pre-filters that prevent clogging by leaves or debris are available at your local store.
5. Use any gentle household cleanser and a soft brush or cloth to clean the fountain. Avoid harsh chemicals, abrasives, or rough scrubbing which may damage the finish of your fountain.

Cleaning the Pump

Disassemble the pump by removing the filter and regulator/impeller plate. Remove the impeller/rotor assembly by gently pulling on the impeller blades. Use a soft cloth or brush to clean the area inside the pump housing. Clean the filter, gland, and impeller in warm, soapy water. Reassemble the pump and inspect it for proper operation.

FAQ

• Q: What type of water should I use to fill the fountain?
• A: Distilled water is recommended, but if not available, filtered water can be used. Tap water may contain minerals and chemicals that can build up and leave a residue.
• Q: How often should I clean the fountain?
• A: The cleaning frequency depends on the location of the fountain. Clean it when visibly soiled or when there is a decrease in performance. Regularly remove debris every other day and clean the fountain monthly to prevent mineral buildup and clogging.
• Q: Can I use harsh chemicals to clean the fountain?
• A: No, it is recommended to use a gentle household cleanser and a soft brush or cloth. Avoid using harsh chemicals, abrasives, or rough scrubbing as they can damage the fountain’s finish.
• Q: How do I clean the pump?
• A: Disassemble the pump by removing the filter and regulator/impeller plate. Clean the pump housing, impeller, filter, and gland in warm, soapy water. Reassemble the pump and check for proper operation.

WHAT IN THE BOX

Any questions? Please contact our customer support team by email or phone.
We are always ready to assist you! Please have the product item number ready, (located on the first page of this instruction manual) and your order number available.

Assembly Instruction and Using Your Product

Exploded Drawing, List of Product Parts, and a Step-by-Step illustration of the assembly.

1. Unpack the contents of the box.

2. Assemble the fountain on a surface that will not be damaged by water.

3. Please place the pump upright into the basin and draw the pump power cord out through the opening at the back of the fountain.

4. Place each of the mesh screens inside the appropriate bowl, based on size. Add clean water to the lowest bowl (basin) of the fountain.
   The water level should be approximately 1 in / 25 mm below the top of the opening at the back of the basin where the water circulates from.

5. Connect the pump to a GFCI outlet and the product will begin to function as intended.

6. If the water flow is higher or lower than desired, adjust the regulator dial/slide on the front of the pump, (+) to increase the water flow or (-) to decrease the water flow.

7. The LED lights are preassembled, but they are replaceable. When replacing them, please refer to Steps 1 and 2.

8. To eliminate the possibility of water damage around your fountain, check for leaks and excessive splashing after the initial setup of your fountain.
   It is highly recommended to place the fountain in an area where it cannot cause damage due to excessive splashing.

9. Do not leave your fountain running for extended periods when no one is present to observe the performance.

10. Check the area around your fountain regularly to ensure that there is no leakage.

Important Safety Instructions

PUMP
CAUTIONS

1. To avoid the risk of electric shock from the pump, observe the following cautions:
2. This pump is intended to be used with water only.
3. Do not use the pump in water exceeding 86°F / 30°C.
4. Do not use the pump in flammable liquids.
5. Do not use the pump for industrial purposes.
6. Do not use the pump in vehicles or on board ships aircraft or swimming pools.
7. Do not use the pump in a location where special conditions prevail, such as the presence of a corrosive or explosive atmosphere (dust, vapour or gas).
8. Do not let the pump run dry. The pump must be completely submerged for proper operation and cooling.
9. Do not lift the pump by its power cord.
10. Keep the plug dry. Do not expose the plug to water or steam.
11. Before connecting to the power source, make sure that the pump is assembled and completely submerged in water.
12. Always disconnect the pump from the power source before performing any maintenance on the pump, lights (if equipped), or fountain.
13. Do not exceed the voltage shown on the pump.
14. Check the water level regularly to ensure the pump is completely submerged during operation.
15. Do not add water while operating the product. Always disconnect the pump from the power source before adding water.

WARNING

1. To reduce the risk of electric shock, this pump is equipped with a grounding conductor and grounding-type attachment plug.
2. Be certain that it is connected only to a properly grounded, grounding-type receptacle. Use only portable self-contained fountains no larger than 5 ft / 1.52 m in any dimension.
3. If equipped with a 3-prong, grounded-type plug, do not remove the grounding pin from the plug on the power cord.

Care and Maintenance

Water

1. Distilled water is always recommended to fill your fountain, or filtered water if distilled is not an option. (Tap water may contain minerals and chemicals that may build up and leave a residue.)
2. A chece thing or er le pel me. as me the thin dry, hot climate lets water wired pirate very quickly. The sire’s toe foolin’ I also impact the rate of evaporation – the larger the fountain, the quicker water will evaporate.

Cleaning Frequency

1. Regular cleaning of your fountain and pump will depend on where it is located. When the fountain or pump is visibly soiled, or there is a decrease in performance, please follow the care and maintenance tips below. Failure to clean and maintain the pump will result in overheating.
2. Keep the fountain water and pump clean and clear of debris. Remove any leaves or other debris every other day.
3. Clean your fountain monthly to prevent mineral buildup and contamination, which may clog the pump. (This frequency may vary depending on where your fountain is located.)
4. Water treatments that prevent algae growth and mineral deposits and pre-filters that prevent clogging by leaves or debris are available at your local home and garden stores. Do not use bleach as it may be harmful to pets and wildlife and may damage your fountain.
5. Disconnect the pump from its power source and empty the water from the fountain. (Do not tip the fountain to empty the water – use a siphon pump or small bucket.) Use any gentle household cleanser and a soft brush or cloth to clean the fountain. Avoid harsh chemicals, abrasives, or rough scrubbing which may damage the finish of your fountain.

Cleaning the Pump
Disassemble the pump by removing the filter and regulator/impeller plate. Remove the impeller/rotor assembly by gently pulling on the impeller blades. Use a soft cloth or brush to clean the area inside the pump housing. Clean the filter, gland, and impeller in warm, soapy water. Reassemble the pump and inspect it for proper operation.

Operation

1. Although it is not required, pumps generally last longer if left running continuously, reducing wear and tear from starting and stopping. Be sure to keep the fountain ¾ full of water.
2. If mosquitoes are a problem in your area, it is recommended to run the fountain as much as possible to prevent standing water, where mosquitoes breed. You may also add a few drops of anti-mosquito water treatment to the fountain water. (Also available at local home and garden stores.)
3. If the fountain is not in use for an extended period, disconnect the power and empty the fountain.
4. Do not operate the fountain in temperatures below 41°F / 5°C to prevent frost damage. During winter months, before the temperatures drop, disconnect the power, drain the fountain, and store it in a heated area. If the fountain is stored outdoors, disconnect the power, drain the fountain, and remove the pump and any lights. Once completely dry, cover the fountain with a tarpaulin.

Prevention

1. Place the fountain in a location that it won’t be susceptible to damage, or where splashes and potential leaks will not cause damage to the surrounding area.
2. Check for leaks and monitor the fountain for excessive splashing after initial installation regularly.
3. If the fon, an evil ate sit or one sible. The detected pest was. Em cy ene Sintain no eat me crack it. last epoxy or tier Silicone Il sealant. (Also available at local home and garden stores.) Wait for the sealant to dry before refilling the fountain and using it again.

Non-Solar Lighting
Your fountain may be connected to an outdoor-rated outlet timer to activate the lights during nighttime hours. Please note on some models, the lights do not operate separately from the pump, so when the lights are on, the pump is on, and vice versa.

Non-Solar Lighting
Your fountain may be connected to an outdoor-rated outlet timer to activate the lights during nighttime hours. Please note on some models, the lights do not operate separately from the pump, so when the lights are on, the pump is on, and vice versa.

Troubleshooting Guide

If the pump does not operate…

1. Check to make sure the pump is connected to a power source.
2. Check the water level to ensure the pump is completely submerged. Add water as needed.

If the pump operates, but, there is no water flow…

1. Check the water level to ensure the pump is completely submerged. Add water as needed.
2. Check the supply tube for any kinks or folds and correct them.

If the pump operates, but there is no water flow the pump is fully submerged and the supply tubing has no kinks…

1. Disconnect the pump from the power source.
2. Disconnect the supply tube from the pump outlet.
3. Check for clogs or holes and clean the tubing inside and outside if necessary.
4. Check for clogs and clean the pump inlets and outlet if necessary.
5. Place the pump back into the water outlet side up and then re-connect the pump to the power source.
6. Once the water begins to flow from the pump, re-connect the supply tubing to the pump outlet.
7. Check for any air trapped in the water supply tube which may prevent the pump from working.

If the pump runs with low or high water circulation…

1. Check and adjust the regulator dial or slide on the front of the pump. Adjust the dial/slide towards (+) to increase water flow or towards (-) to decrease water flow.

If the pump operates, but the water flow is uneven or non-existent and the pump makes noise…

1. Check the impeller assembly for wear. Remove the front cover and regulator/impeller plate and remove the impeller assembly. Clean the impeller assembly and inspect it for wear. If the rotor spins freely from the magnetic body, the impeller assembly is worn and needs to be replaced.
   Contact customer service for replacement parts.

If the pump starts to make noise…

1. Check the water level to ensure the pump is completely submerged. If the water level drops below the pump intake, it may suck in air and cause the noise or the pump to completely stop working.
2. Move the pump away from the sides of the basin or place a piece of foam or sponge underneath the pump to isolate any vibration that causes the noise.

If the water starts to foam…

1. Check the water level to ensure the pump is completely submerged. If the water level drops below the pump intake, it may suck in air and cause the pump to ‘spit and foam the water.
2. Add a few drops of anti-foaming water treatment, available at your local home and garden store, to the fountain water.

If the water flow is uneven…

1. Gently sweep across the water surface to achieve even water flow across the face of the fountain.
2. Check the top of the basin to ensure it is level. If not, shim the basin from the bottom until the top spillway is level or has achieved even 04 water flow all around.

WARRANTY

All components are warranted by the manufacturer for a period of so days after the date of purchase by the original owner against defects in materials workmanship under normal use. If it is appropriate to replace your product due to specific defects, the manufacturer will replace the purchase with the same product or a comparable product.
For specific instructions on how to obtain warranty service for your product, please contact Customer Support using the contact information provided.

LIMITATIONS
All components are warranted by the manufacturer for 30 days after the date of purchase by the original owner against defects in materials & workmanship under normal use. If it is appropriate to replace your product due to specific defects, the manufacturer will replace the purchase with the same product or a comparable product.

GENERAL TERMS & CONDITIONS

1. Proof of purchase is required to request a claim under this warranty.
2. This warranty applies only to manufacturer errors & defects. The warranty applies to the following:
   • Breaks and cracks in the product that originated with the manufacturer.
   • Missing pieces.
   • Stains that occurred during the manufacturing process.
3. This warranty does not apply to the following:

• Damage due to improper loading, handling, or transportation.
• Any costs associated with the installation and removal of products or parts are subject to this warranty.
• Acts of God.
• Products that have been subject to negligence, abuse, accident, misapplication, tampering, alteration, or modification.
• Products that have been subject to improper installation, operation, maintenance, repair, or storage.
• Products that have been subject to defects that occur when this product is used incorrectly and/or outside of normal application purposes.
• Products that have had, including but not limited to, operational failures caused by corrosion, rust, or other foreign materials in the system, or operation at pressures above recommended maximums.
• All other possible defects not mentioned here that would not have occurred during manufacturing or correct, routine use of the item.

INSTRUCTIONS
For specific instructions on how to obtain warranty service for your product, please contact Customer Support using the contact information provided. In most circumstances, you will need to return your product either in its original packaging or in equally protective packaging to the address specified by Customer Support.
Before delivering your product for warranty service, it is your responsibility to remove all personal items and belongings you may have stored with your product. Teamson is not responsible for the possible loss, destruction, or damage of any personal items or belongings that have been sent with the product.

DISCLAIMER
Any oral statements made about the product by the seller, the manufacturer, the representatives, or any other parties do not constitute warranties, should not be relied upon by the user, and are not part of the contract for sale. The seller and manufacturer’s only obligation, and buyer’s only remedy shall be for the manufacturer to either replace and /or repair at the manufacturer’s sole discretion, the product as described above. Neither the seller nor the manufacturer shall be liable for any injury, loss or damages for lost profits, lost sales, injury to person or property, or any other incidental or consequential loss arising from any cause whatsoever, no matter whether based upon warranty, contract, negligence or other misuse, and the buyer and user agree that no other remedy shall be available to them. Before using, the buyer and user shall determine the suitability of the product for intended use, and assume all risk and liability whatsoever in connection therewith. The warranty and remedy described in this limited warranty is an exclusive warranty and remedy in place of any other warranty or remedy expressed or implied. All other warranties and remedies are hereby expressly excluded, including but not limited to any implied warranty of merchantability or fitness for any particular purpose.

OTHER LEGAL RIGHTS
This warranty gives the buyer and user specific legal rights, and the buyer and user may also have other rights which vary from state to state. Some states do not allow exclusions or limitations of incidental or consequential damages, so the above limitations or exclusions may not apply to you.
THANK YOU
We appreciate the trust and confidence you have placed in Teamson through the purchase of this product. We strive to continually create quality products designed to enhance your home and life. Visit us online to see our full line of products available for your home décor, toy, and pet needs. Thank you for choosing Teamson!

Exploded Drawing

Product Parts

Step-by-Step Illustrations

Step 1

Step 2

Global Customer Support

USA / CA

• support@teamson.com
• +1(770) 246-4898
• Mon – Fri 9 AM – 4 PM EST

EU / UK

• support@teamson.co.uk
• +44(0)1952-916-050
• Mon – Thur 9 AM – 5 PM GMT
• Fri 9 AM – 4 PM GMT

ASIA

• sales_ec@teamson.com
• +86(0755)8885-3558.5 115108
• Mon – Sat 9 AM – 5 PM GMT+8
• support@teamson.com.tw
• +886(2)2556-6268
• Mon – Fri 9 AM – 5 PM GMT+8

AU

• support@teamson.com.au.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>