webstaurantStore ET-999SN Automatic Sealing Machine Instruction Manual

webstaurantStore ET-999SN Automatic Sealing Machine

Product Information

• Specifications
  • Model: ET-999SN, ET-95SN, ET-899, ET-58
  • Features: Film Clamp, Film Sensor, Roller, Film Pin, Lower Mould Plate, Cup Jack, Lower Mould, Safety Door, Front Panel, Film Collector

Product Usage Instructions

• Fill in the Film
  • Follow the steps below to fill in the film correctly:
  • Ensure the film is loaded in the correct direction.
  • Match the eye-mark of the film to the place of the film sensor.
• Power On and Temperature Adjustment
  • Follow the steps below to power on and adjust the temperature:
  • Plug in the AC power wire and turn on the power button.
  • The lower mould will push out simultaneously.
  • The upper mould will automatically increase the temperature.
  • After 5-7 minutes, the temperature indicator will shut off when the upper mould’s temperature is set and ready.
• Choosing Container and Film
  • Follow the guidelines below to choose the container and film:
  • PET/ES film is suitable for any kind of tray with a temperature range of 140-160 degrees.
  • For optimal sealing, ensure that both the container and film are made of PS material.
• Front Panel Introduction
  • Indicator
  • The front panel features a power indicator that indicates whether the power is online or offline. The power key is used to start up the machine.
  • Function of Buttons
  • The front panel includes an Auto/Manual choice key that allows you to select between auto and manual operation.

FAQs

• Q: What are the LED indicators on the machine?
  • A: The LED indicators represent different functions of the machine:
  • Lower Mould/Cup Input
  • Upper Mould Sealing
  • Upper Mould Standby
  • Lower Mould/Cup Output

INSTRUCTIONS

• A. Each unit provided with a 2-wire polarized attachment plug shall be provided with the following instructions: “To reduce the risk of electric shock, this appliance has a polarized plug (one blade is wider than the other). This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician to install the proper outlet. Do not change the plug in any way”.
• B. Each unit intended for household use shall include the following instructions: “Household indoor use only ” and “Close supervision is required when this product is used near children.
• C. A household heating appliance provided with a power-supply cord less than 1.4 m (4½ ft.) in length shall be provided with the following instructions:
  • a. A short power-supply cord (or detachable power supply cord) is provided to reduce the risk resulting from becoming entangled in or tripping over a longer cord.
  • b. Extension cords (or longer detachable power-supply cords) are available and may be used if care is exercised in their use.
  • c. If an extension cord (or a longer detachable power-supply cord) is used, (1) the marked electrical rating of the detachable power-supply cord or extension cord should be at least as great as the electrical rating of the appliance, (2) if the appliance is of the grounded type, the extension cord should be a grounding-type 3-wire cord, and (3) the longer cord should be arranged so that it will not drape over the countertop or tabletop where it can be tripped over, snagged, or pulled on unintentionally (especially by children).

CHARACTERISTIC INTRODUCTION

CHARACTERISTIC INTRODUCTION ET-999SN ET-95SN ET-99SU ET-99MU

1. FILM CLAMP
2. FILM SENSOR
3. ROLLER
4. FILM PIN
5. LOWER MOULD PLATE
6. CUP JACK
7. LOWER MOULD
8. SAFETY DOOR
9. FRONT PANEL
10. FILM CLAMP
11. FILM COLLECTOR

1. UPPER MOULD
2. IN-OUT SENSOR
3. SLIDE
4. CUP JACK
5. BEARING
6. JUMP ROD
7. BEARING BUSH 605zz
8. BEARING BUSH 699zz

ET-899

1. FILM CLAMP
2. FILM SENSOR
3. ROLLER
4. FILM PIN
5. LOWER MOULD PLATE
6. CUP JACK
7. LOWER MOULD
8. SAFETY DOOR
9. FRONT PANEL
10. FILM CLAMP
11. FILM COLLECTOR

1. UPPER MOULD
2. IN-OUT SENSOR
3. SLIDE
4. CUP JACK
5. BEARING
6. JUMP ROD
7. BEARING BUSH 605zz
8. BEARING BUSH 699zz
9. EMERGENCY BOTTON
10. TEMPERATURE CONTROLLER
11. COUNTER
12. POWER
13. START BUTTON
14. AUTOMATIC/MANUAL CONTROL

ET-58

Please turn off the power when maintaining.

• Warning! Sharp knife edge.
• Warning! High Temperature.

1. FILM SENSOR
2. FILM ANCHORAGE
3. LOWER MOULD PLATE
4. LOWER MOULD
5. SAFETY DOOR
6. FRONT PANEL
7. FILM CLAMP
8. FILM COLLECTOR

1. UPPER MOULD
2. SLIDE
3. CUP JACK(BIG)
4. BEARING
5. BEARING BUSH 605zz
6. BEARING WHEEL

OPERATION

• Please turn off the power when maintaining.
• Warning! Electric shock.

FILL-IN THE FILM

1. Fill in the film in correct direction as in the above picture. If you fill in the wrong way, the film will be stuck with the heater of the upper mould. After loading the film, please match the eye mark of the film to the place of the film sensor.
2. Plug the AC power wire, and turn on the power button, the lower mould will push out at the same time. Further, the upper mould will increase the temperature automatically.
3. After 5~7 minutes, the TEMPERATURE INDICATOR shall shut off when the upper mould＇s temperature is ready. Till now, the auto function is ready for work. It could be only in manually while the temperature is not ready.
4. The way to choose the container and film:
   • PET/ES film is suitable for any kind of tray. (temperature range 140~160 °C)
   • As for sealing well, the material of both container and film should be the same. (temperature range 160~180°C)
   • PS： Unemployed and children are forbidden to close to the machines. To forbid an accident, don＇t put your hands in the machines unless you pull out the power wire.

Rolling System

• Step1.
  • Take off the Right side of Plastic film clamps 1 & [Spring Washer]  Butterfly Clamps J
• Step2.
  • Put the Right side of [Plastic film clamps into the central paper roll of flim to both sides
• Step3.
  • OK
• Step4.
  • Put the object as a picture step onto the Rolling System
• Step5.
  • After putting the Flim onto the system then put on the WasherJ first and Spring. & Butterfly Clamps
• Step 6.
  • FILL IN THE FILM
• Step 7.
  • Put the film behind the iron Bar.
• Step8.
  • Turn on the [ManualOperateJ the film is OK to be rolled on the film system.

FRONT PANEL INTRODUCTION

Indicator

The function of buttons:

1. Power indicator: Indicating the power is online or offline.
2. Power key: Press the power key to start up the machine. After displaying the “YF-LCC＂ pattern, the machine begins to service you. Oppositely, the “PO＂ pattern means the power is off.
3. Auto/Manual choice key: Providing you to select auto or manual operation;
   • A. If the manual is selected, the machine is waiting for pressing the manual key to go on the sealing process.
   • B. If auto is selected, the machine is automatically doing the sealing process. (Cups will be sealed automatically.)
4. Manual Operate KEY: Work in situation 3-A.
5. Reset key: Reset the function of the microcomputer＇s parameters and special function.
6. Temperature Key: Lighting up as increasing temperature, off oppositely.
7. Right screen:
   • A. To display the temperature as usual condition.
   • B. To display the parameter of a function as changing the parameter setting.
   • C. To display error code.
8. 〝UP〞 and 〝DOWN〞Keys: To increase or decrease one unit value.
9. Counter Key: To display the amount or count back to zero.
10. Left screen:
    • A. To display the amount as usual condition.
    • B. To display the parameter setting. Symbolizing P1~P5.

LED Indicator

Function of setting

System parameter table:

Operating procedures

The procedures of machine as: A->B->C->D->E->F->G->H->I

• A. Press POWER to display YF/LCC, then the left screen shows the counter and the right screen shows TEMP. The machine is now ready for use.
• B. Press the SET key, the left screen displays P1， the right screen displays temperature, then use the up or down key to increase or decrease one degree.（PP film 160~180℃，ES film 140~160℃）
• C. Press the SET Key, then the left screen displays P2, and the right screen shows counting mode, OPN means can be reset to zero and recounting from one， LOK means cannot be reset to zero, but continuously counting day after day.
• D. Press the SET key once more, the left screen shows P3 and the right screen shows sealing time, then use the up and down keys to increase or decrease the value by one unit (0.1 seconds). Generally, the value is assigned between 005 and 015.
• E. Press the SET key once more, the left display shows P4 and the right display shows cup settling time, then use the up and down keys to increase or decrease the value by one unit (0.1 second). Generally, the value is assigned between 005 and 010.
• F. Press the SET key once more, the left display shows P5, and the right display shows plastic paper advancing time. If the paper has a sensed point (eye mark), then set the value at 000, else depends on the length of the paper unit, and use up and down key to adjust the correct time, generally set around 006 and 020.
• G. Press the SET key once again, the left display shows YF, and the right display shows LCC, which means all set procedures are finished. The left display goes to normal counting, and the right display shows the temperature of the heater, and going to warm up.
• H. As the temperature is ready, the machine goes to normal working, according to AUTO mode or MANUAL mode.
• I. To stop the machine, only need to press the POWER key once again, the lower mould will draw back; the left and right displays are going off. At this time, the power indicator is still on, and that’s normal. This means the controller is sleeping, press POWER key once again to wake it up if you want to work continuously. To off the power indicator, you need to unplug the power line.

System error codes:

The machine is going to buzz as the microcomputer detects any failures.

• A. E00： Temperature control system error.
• B. E01： Heating circuit or temperature wire error.
• C. E02： Upper motor drawback or micro switch error.
• D. E03： Lower motor advanced or micro switch error.
• E. E04： Sealing film is not in the right position or the eye-marks not detected.
• F. E05： Lower motor draw back micro switch error.
• G. E06： Upper motor advanced or micro switch error.
• H. E07： Safety door is touched or collided.
• I. E19： P.C board error.

To stop the buzzer, please off the power for five seconds, then on the power gain, if it is still buzzing, please contact your local dealer for service.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>