KERI SYSTEMS EntraGuard Titanium Telephone Entry Controller Installation Guide
- June 17, 2024
- KERI SYSTEMS
Table of Contents
KERI SYSTEMS EntraGuard Titanium Telephone Entry Controller
Product Information
Specifications
- Product Name: EntraGuard Titanium Telephone Entry Controller
- Model Number: P/N 01551-001 Rev. B
- Compatibility: Can be used alone or connected to an access control network using PXL-500 or PXL-250 family controllers
- Power Requirement: The unit must be powered down before making or removing any connections
- Jumper Setting: Jumper 11 must be set if using the internal modem of the Titanium controller
Product Usage Instructions
Section 1 – Drawings
The drawings section provides visual representations of the EntraGuard Titanium Telephone Entry Enclosure (Figure 1) and the Titanium Telephone Entry Controller (Figure 2).
Section 2 – RS-232 Serial Port
2.1 Direct Serial Connection
To establish a direct serial connection, you will need the Keri Systems cable with part number KDP-552. Connect the PC/DB-9F end of the cable to the PC and the Telephone Entry/TB-12 end to the Titanium controller’s RS-232 serial port (refer to Figure 3).
2.2 Modem Connection
If you intend to use the Titanium controller’s internal modem, you will need the Keri Systems cable with part number KDP-929M. Connect the Modem/DB-9M end of the cable to the modem and the Telephone Entry/TB-12 end to the Titanium controller’s RS-232 serial port (refer to Figure 4).
Section 3 – Setup Controller
This section provides instructions on setting up the controller.
3.1 Set Unit Address
To set the unit address of the controller, follow these steps:
- Ensure the controller is powered up and access the Reset Menu (refer to Figure 5).
- Press 1 on the keypad to access the Set Panel Address screen (refer to Figure 6).
- The address range is from 1 to 128. The Master Controller must be set to address 1. Other slave EntraGuard/PXL controllers can be assigned any number from 2 to 128.
- If the current address displayed is correct, you can either enter the same address and press or just press to return to the reset menu.
- If you need to change the address, enter a new address and press *. Note that changing the address will erase all information within the controller, so make sure to collect all event data before proceeding.
If you do not enter a new address or enter the same address that is already assigned to the unit, you will need to clear the memory separately (refer to “Clear the Controller’s RAM” on page 5).
FAQ
- Q: Can the EntraGuard Titanium controller be used alone?
- A: Yes, the EntraGuard Titanium controller can be used alone or connected to an access control network using PXL-500 or PXL-250 family controllers.
- Q: What happens if I don’t power down the unit before making or removing connections?
- A: Failure to power down the unit before making or removing connections can result in damage to the controller.
- Q: How do I set the unit address of the controller?
- A: To set the unit address, access the Reset Menu, press 1 on the keypad, and follow the instructions in Section 3.1 of the user manual.
- Q: What happens if I change the address of an EntraGuard Titanium controller?
- A: Changing the address of an EntraGuard Titanium controller will completely erase all information within the controller. It is important to collect all event data before changing the address as the event information will be lost and cannot be recovered.
Installation
This installation guide provides basic installation information, drawings, and
controller setup instructions to use when installing the EntraGuard Titanium
Telephone Entry controller. The EntraGuard Titanium controller may be used
alone or may be connected to an access control network using PXL-500 or
PXL-250 family controllers. For instructions on how to install a postal lock,
see the EntraGuard Titanium Postal Lock Installation Application Note (P/N
01964-001).
NOTE: It is the responsibility of the installation organization to have
only technically qualified personnel performing the installation.
- Section 1 – Drawings
- Section 2 – RS-232 Serial Port
- Section 3 – Setup Controller
- Section 4 – Contact Keri Systems
Drawings
Figure 1: The EntraGuard Titanium Telephone Entry Enclosure
Figure 2: The Titanium Telephone Entry Controller
- NOTE: You must power down the unit before attempting to make or remove any connections. Failure to do so will damage the controller.
- NOTE: You must set Jumper 11 if you intend to use the Titanium controller’s internal modem.
RS-232 Serial Port
An RS-232 serial connection between the EntraGuard unit and the host computer can be done one of two ways:
- by a direct serial connection (50 feet maximum)
- through an external modem
Direct Serial Connection
The Keri Systems part number for this cable is KDP-552.
Figure 3: PC/DB-9F to Telephone Entry/TB-12 RS-232 Direct Serial Connections
Modem Connection
The Keri Systems part number for this cable is KDP-929M.
Figure 4: Modem/DB-9M to Telephone Entry/TB-12 Serial Port Connection
Setup Controller
If you’re turning system power on for the first time, certain tasks must be
performed prior to entering access control information from Doors. On the
EntraGuard Titanium main board (see Figure 2 on page 2), hold the Reset Button
(SW1) down and turn the controller’s power on. After the controller beeps
once, indicating the controller’s firmware is ready for programming, release
the SW1 button. The LCD on the front panel will display the Reset Menu (see
Figure 5). From this menu you may perform these tasks: set the controller’s
address, clear the controller’s memory, set the microphone volume, and check
diagnostics.
Figure 5: Reset Menu
NOTE: If no keys have been selected within 60 seconds, the unit will time out and go directly to the default message. In order to reach the Reset Menu, the unit must be powered up again.
Set Unit Address
The controller’s address may only be set through the Reset Menu. Once you have
performed the necessary steps to reach the Reset Menu as described above. To
set the desired operating address for the controller, press 1 on the keypad.
The Set Panel Address screen appears on the LCD (see Figure 6).
Figure 6: Set Unit Address
The address range is from 1 to 128. The Master Controller must be set to
address 1. Other slave EntraGuard/PXL controllers may be assigned any number
from 2 to 128. If the network is made up of PXL-250s, the EntraGuard Titanium
must be set as the Master.
If the address shown as Current is correct, you may either enter the same
address and press , or just press to return to the reset menu. If you do
not enter a new address, or enter the same address that is already assigned to
this unit, you will need to clear the memory separately (see “Clear the
Controller’s RAM’’ on page 5).
NOTE: Changing the address of an EntraGuard Titanium controller
completely erases all information within the controller. It is vitally
important that you collect all event data from the controller before changing
the address. Once the address is changed (and the RAM is automatically
cleared) the event information in the controller is lost and cannot be
recovered.
If the address shown as Current needs to be changed, enter the new address by
pressing the numbers on the keypad. The number selected will show in the New
line. If you enter the wrong number, simply press CLEAR to erase what has been
entered. When you are satisfied with the address entered, press *. If you have
changed the number from what is shown as Current, the controller will
automatically clear the memory as it changes the address (see Figure 7
).
Figure 7: Clearing Memory
Once the memory has been cleared, the unit is ready to be configured. The LCD will display a warning that the unit has not been initialized. This display will rotate with the EntraGuard Default display until a Total Update from Doors has been performed on the unit. Once an update has been performed, only the default will be displayed.
Clear the Controller’s RAM
When turning system power on for the first time, the controller’s memory needs
to be cleared of any spurious information that may be in the RAM. If you
change the controller address, the memory is automatically cleared. However,
if you did not change the address, you will need to clear the controller’s RAM
separately. From the Reset Menu (see Figure 5 on page 4), press 2 to Clear
Memory. The Clear Memory screen will appear on the LCD (see Figure 8).
Figure 8: Clear Memory
From the Clear Memory Screen, you may either:
-
Press 1 to clear the controller’s RAM. The LCD will change to show the memory is being cleared (see Figure 7). Once the controller’s RAM has been cleared, the unit is ready for use. The LCD will rotate between the Initialization Warning and EntraGuard Default screens until a Total Update from Doors has been performed on the unit.
or -
Press 2 to return to the Reset Menu without clearing the controller’s RAM.
NOTE: Clearing the system RAM completely erases all information within the EntraGuard Titanium controller, except for the controller address. If there is any information in system RAM from an access control installation and the system RAM is cleared, the information in the controller is lost and cannot be recovered, and a Total Update must be performed.
Diagnostics and Troubleshooting
For information regarding the diagnostics screens and troubleshooting the EntraGuard Titanium Controller, see the EntraGuard Troubleshooting and Diagnostics Guide (P/N 01912-001).
Contact Keri Systems
| Keri USA | Keri UK, Ireland, Europe |
|---|---|
| 2305 Bering Drive San Jose, CA 95131 | Unit 17 |
Park Farm Industrial Estate Ermine Street Buntingford
Herts SG9 9AZ UK
Telephone: 800-260-5265
| Telephone: + 44 (0) 1763 273 243
Fax: 408-577-1792| Fax:+ 44 (0) 1763
274 106
Web: www.kerisys.com|
Web:www.kerisystems.co.uk
E-mail: sales@kerisys.com
techsupport@kerisys.com|
E-mail:sales@kerisystems.co.uk tech-
support@kerisystems.co.uk
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>