KENWOOD KSC-50CR Charger Pocket Instruction Manual

KENWOOD KSC-50CR Charger Pocket

FCC WARNING

This equipment generates or uses radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved by the party responsible/ JVC KENWOOD. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

INFORMATION TO THE DIGITAL DEVICE USER REQUIRED BY THE FCC
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can generate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that the interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

•  Reorient or relocate the receiving antenna.
•  Increase the separation between the equipment and receiver.
•  Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
•  Consult the dealer for technical assistance.

SUPPLIED EQUIPMENT

Charger pocket Instruction manual

APPLICABLE AC ADAPTER
Use the AC adapter listed below.

• KSC-44SL
• KSC-44ML

APPLICABLE BATTERY PACK

Charge only the battery pack listed below. Other types of batteries may burst, causing personal injury.

CHARGING TIPS

• Using the transceiver while charging its battery pack will  interfere with correct charging.
• If the operatin  time of a battery pack decreases although the  battery pack is fully and correctly charged, the battery pack
•  The ambient temperature should be from 5°C to 40°C (41°F to  104°F) while charging is in progress.
•  This charging time aries depending on the degree of  discharge and the ambient charging temperature.
•  This charger may be suitable to charge battery packs not  listed herein, due to further technology development.
•  If the transceiver contacts are not properly mated with the  charger terminals, the indicator may flashing red or may

JOINTING THE CHARGER
Please use the charger rear nail to connect the charger as shown below.

1. Connect the DC plug of the AC adapter to the DC IN jack on the bottom of the Charger.
2. Plug the AC adapter into an AC outlet.
3. Slide a transceiver equipped with a battery pack into the charging pocket.
4. Make sure the metal  contacts of the transceiver mate securely with the charger terminals.
5. The indicator lights red and charging starts.
6.  When charging is completed, the indicator flashing green. Remove the transceiver from the charging slot.

Approximate Charging Times
4.5 hours

Charger Status Table

Flashing Red

| The battery pack is defective or the transceiver contacts are not properly mated with those of the charger.
Flashing Green| Charging is completed; remove the battery pack from the charger.

Alternates flashing green and orange

| The temperature of the battery pack has not satisfied the charging start temperature. Remove the battery pack from the charger and wait until it reaches a normal temperature before charging it again.

SAFETY PRECAUTIONS

Please read all safety instructions before using this charger. For best results, be aware of all warnings on the charger, the battery pack, and the product using the battery pack.

•  Do not disassemble the charger. Incorrect reassembly can cause fire or electric shock.
•  Use of an attachment not recommended by nor sold by KENWOOD can cause fire, electric shock, or injury.
• • Do not expose the charger  to rain or moisture,to avoid the risk of fire or electric shock.
•  Prevent strong mpacts, such as caused by dropping, since the charger can be damaged.
•  Do not use the charger in hot or humid environments, in direct sunlight, nor near heaters.
•  Do not use solvents such as benzene or paint thinner to clean the charger.

SPECIFICATIONS

• DC Input Voltages: 5.5 V DC only
• Dimensions (W x H x D)/ Weight:
• 75.8 x 91.3 x 56.1 mm/ Approx. 105 g
  Note :  The charger specifications are indicated on the bottom plate of the charger.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>