IGLOO ICE102-WHITE Portable Electronic Ice Maker User Manual

IGLOO ICE102-WHITE Portable Electronic Ice Maker

Specifications:

• Model: ICE102-WHITE
• Class: 1
• Electrical Requirements: 115V/60Hz
• Ice Making Current: 2.7 A
• Ice Harvest Current: 1.9 Amp
• Refrigerant: R134a/2.3 Oz.
• Design Pressure: 290 Psig (High Side), 88 Psig (Low Side)
• Dimensions: 11.7 x 14.5 x 14.9 inches
• Weight: 26.4 lbs (12 kg)
• Enclosure: ABS plastic

Product Usage Instructions

Unpacking Your Ice Maker:

1. Inspect and remove all packing materials, including foam and adhesive tape, from both inside and outside the unit.
2. Remove any remains of packing, tape, or printed materials before powering on the appliance.

Product Registration:

Thank you for purchasing this quality IGLOO product. To obtain warranty service, please keep the following information:

• Model number
• Ice maker serial number
• Date of purchase

Staple your receipt to your manual as you will need it for warranty service.

Safety Instructions:

Electrical Requirements:

This appliance must be plugged into at least a 15 AMP 110-115 VOLT 60 Hz GROUNDED OUTLET. The appliance must be grounded and is equipped with a 3-wire cord having a grounding plug. Make sure to plug it into a properly installed and grounded outlet.

Extension Cord:

Avoid using an extension cord, but if necessary, follow these guidelines:

1. Use only 3-wire extension cords with a 3-blade grounding plug.
2. The rating of the extension cord must be equal to or greater than the rating of the appliance.
3. Position the extension cord so that it does not drape over the counter or tabletop where it can be pulled on by children intentionally.

Maintenance and Cleaning:

Before performing any maintenance or cleaning, make sure to unplug the appliance from the power supply or disconnect it at the household distribution panel by removing the fuse or switching off the circuit breaker.

Parts, Functions, and Features:

1. Cover with transparent window
2. Ice maker and pusher
3. Water reservoir (Not shown)
4. Control panel
5. Water drain cap: for draining water from ice water
6. Compressor cooling fan (Do not block airflow)
7. Ice shovel
8. Ice basket

Control Panel:

The control panel is easy to use and has button functions with LED indicators:

• Power ON LED indicator light
• Power ON/OFF button
• Ice cube SELECT SIZE button
• Selected ice size LED light indicator displaying: SMALL, MEDIUM, and LARGE ice cubes
• ADD WATER (Alerts that there is no water in the water reservoir), must add water
• ICE FULL LED indicator

FAQ

• Question: What should I do if there is no water in the water reservoir?
  • Answer: The control panel will display “ADD WATER” when there is no water in the reservoir. Simply add water to continue making ice.
• Question: Can I use an extension cord with this appliance?
  • Answer: It is recommended to avoid using an extension cord. However, if necessary, use a 3-wire extension cord with a 3-blade grounding plug. Make sure the rating of the extension cord is equal to or greater than the rating of the appliance.
• Question: How do I clean and maintain the ice maker?
  • Answer: Before cleaning or performing any maintenance, unplug the appliance from the power supply or disconnect it at the household distribution panel. Refer to the user manual for specific cleaning and maintenance instructions.
• Question: What should I do if the ice basket is full?
  • Answer: The ICE FULL LED indicator will light up when the ice basket is full. Remove the ice from the basket to continue making more ice.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed, including the following:

1. Read all instructions carefully.
2. DANGER! To protect against risk of electric shock, do not immerse cord, plug or any parts of the unit in water or other liquids.
3. Close supervision is necessary when using this appliance near children. This appliance is not suitable for use by children.
4. Never leave an appliance unattended while in use.
5. Do not place an appliance on or near a hot gas or electric burner, or in a heated oven. Do not place on top of any other appliance.
6. Do not let the power cord of an appliance hang over the edge of a table or countertop or touch any hot surface.
7. Do not operate any electrical appliance with a damaged cord or plug or after the appliance malfunctions or has been dropped or damaged in any manner. If damage is suspected, contact the nearest authorized service centre for examination, repair or electrical or mechanical adjustment.
8. Unplug from power outlet when not in use, before putting on or taking off attachments, and before cleaning.
9. The use of accessory attachments that are not recommended by the appliance manufacturer may cause fire, electric shock or injury.
10. Avoid contact with moving parts when the unit is in operation.
11. Never touch the cooling elements when the unit is in operation.
12. Do not use outdoors.
13. Do not use appliance for other than its intended use.

UNPACKING YOUR ICE MAKER

1. Inspect and remove all packing materials. This includes the foam and any adhesive tape both inside and outside of the unit.
2. Inspect and remove any remains of packing, tape, or printed materials before powering on your IGLOO appliance.

WARNING

Please read this manual carefully before using. Retain it for your future reference.

PRODUCT REGISTRATION

Keep for your records to obtain Warranty Service

Thank you for purchasing this quality IGLOO product.This easy-to-use manual will guide you in getting the best use out of your appliance. Remember to record the model and serial number. They are on a label in back of the appliance.

• Model number
• Ice maker serial number
• Date of purchase

Staple your receipt to your manual.

You will need it to obtain warranty service.

SAFETY INSTRUCTIONS

Electrical Requirements

Wiring and Grounding Instructions This appliance must be plugged into at least a 15 AMP 110-115 VOLT 60 Hz GROUNDED OUTLET. This appliance must be grounded. It is equipped with a 3-wire cord having a grounding plug. The plug must be plugged into an outlet that is properly installed and grounded.

WARNING! Improper use of grounded wire can result in the risk of electric shock. Consult a electrician if necessary. Do not attempt to defeat this safety feature by modifying the plug. Avoid the use of an extension cord because it may overheat and cause a risk of fire. However, if it is necessary to use an extension cord:

• A. Use only 3-wire extension cords with a 3-blade grounding plug.
• B. The marked rating of an extension cord must be be equal to or greater than the rating of this appliance.
• C. It should be positioned such that it does not drape over the counter or tabletop where it can be pulled on by children intentionally.

Attempting any maintenance or cleaning:

To minimize the possibility of electric shock, unplug this appliance from the power supply or disconnect at the household distribution panel by removing the fuse or switching off the circuit breaker before attempting any maintenance or cleaning.

NOTE: Disconnect power plug from the power outlet before maintenance or cleaning

PARTS, FUNCTIONS AND FEATURES

1. Cover with transparent window
2. Ice maker and pusher
3. Water reservoir (Not shown)
4. Control panel
5. Water drain cap: for draining water from ice water
6. Compressor cooling fan (Do not block air flow)
7. Ice shovel
8. Ice basket

Control Panel: Easy to use, button function with LED indicators

• A. Power ON LED indicator light
• B. Power ON/OFF button
• C. Ice cube SELECT SIZE button
• D. Selected ice size LED light indicator displaying: SMALL, MEDIUM, and LARGE ice cubes to make
• E. “ADD WATER” (Alerts that there is no water in the water reservoir), must add water
• F. “ICE FULL” LED indicator

Water Drain: Do not lose any parts. (Failure to put rubber plug back will cause water to leak.)

• A. Drain cap
• B. Rubber plug
• C. Drain spout

Drain water to store or when the appliance will not be used for long periods

OPERATING INSTRUCTIONS

This portable ice maker uses a fully automatic control system, with an advanced microcomputer for easy and convenient ice making. Making ice is simple and fast. Just add water, plug into an outlet, and press the ON button. You can select one of the three ice cube sizes with the touch of a button. When first turning on the unit or during icemaking cycles, the compressor will stay idle for 3 minutes, while energizing. There are warning indicators that alert you to fill water when the reservoir is empty and to remove ice when the storage basket is full. The ice maker also has built-in safeguards that can limit accidental damage, automatically shutting down the system when necessary.

Pre-Operating Instructions

Please read carefully.

1. The tilted angle of the ice maker cabinet should not exceed 45˚ during transportation or use. Do not turn the appliance upside down. Doing so could cause the compressor or refrigerating system to operate incorrectly. When the ice maker is moved or transported, please allow time for the fluids in the compressor to settle. Before using the ice maker for the first time, please wait 2 hours after the unit has been leveled and positioned in its proper place before plugging it in and turning it on.

2. Please ensure the ice maker is level and on a stable table or platform
   to avoid malfunction.

3. The machine must be placed on a dry and level surface with sufficient ventilation, far from heat sources such as ovens, heaters and corrosive gases. Leave an 8″ (20 cm) clearance on all sides of the ice maker for proper ventilation.

4. Do not fill the water reservoir with hot water. This may damage the ice maker. It is best to fill the water reservoir with water of room temperature or lower.

Operating Instructions

1. Open the top cover, take out the ice storage basket and fill the water reservoir with 0.8 gallons (3.2 L) of drinkable (tap, purified or bottled) water to the level mark and replace the ice storage basket.
   Make sure that the water level does not reach above the level mark or the bottom of the ice storage basket. Close the top cover.
   Note: During the operation process, if the level of water in the water reservoir becomes too low, the machine will automatically stop operating and the “Add Water” indicator will appear on the LED display.

2. Plug the unit into a grounded outlet. Push the ON / OFF button on the control panel to turn on the machine.

3. Select the desired size of ice cubes by pressing the S, M, or L ice selector button.

   • S = Small ice cubes (Approx. 7 minutes)
   • M = Medium ice cubes (Approx. 9 minutes)
   • L = Large ice cubes (Approx. 12 minutes)

The ice maker will start making ice soon after. The next cycle of 12 ice cubes is complete (based on water temperature, ambient room temperature and selected ice cube size).

Note: To stop the operation, press the ON/OFF button.

Operating Process

1. Water is pumped from the water storage tank to the water box, which may take up to 1 minute.

2. The icemaking cycle begins when the evaporator rods are dipped into the water box. You will hear the compressor working.

3. It will take approximately 6-12 minutes for each icemaking cycle, depending on the size selected. The larger the size, the more time is needed to make the ice. After the cycle is finished, the water box will tilt forward and the remaining water will flow back into the water storage tank. The evaporator rods will then release the ice cubes.
   Note: If the room ambient temperature is below 60˚ F(15ºC), then small or medium ice cube sizes are suggested to prevent ice cubes from fusing together.

4. Approximately 60 seconds later, the water box will tilt backwards and the ice pusher will push the ice into the ice storage basket. After the water box flips back to its original position, the next icemaking cycle will begin.

5. When the maximum capacity of ice cubes is collected and the ice reaches the temperature sensor, the ice maker will automatically stop operating. The “ICE FULL” LED indicator will light up.
   If more ice is needed, remove the ice from the ice storage basket; then replace the basket into the machine, making sure that the basket is placed back to its original position. Note: When replacing the basket, ensure that the temperature sensor is above the basket so that the machine operates properly.

6. To continue making ice, check that there is water in the water storage tank. If there is no water in the water storage tank, then no water will be pumped into the water box, and the operation will stop. The “Add Water” LED display will light up. Press the “OFF” button. Fill the water storage tank with water, and then press the “ON” button for the ice maker to begin operating again. Allow the refrigerant inside the compressor at least 3 minutes to settle before restarting.

7. If the compressor stops for any reason such as water shortage, too much ice, power off, etc., do not restart the machine right away. Wait at least 3 minutes before restarting the machine.

CLEANING AND MAINTENANCE

Before using your ice maker, it is strongly recommended that you clean the appliance thoroughly. Be sure to clean the ice maker regularly.

1. When cleaning, please make sure the power has been turned off and the plug is disconnected from the outlet. When plugging or unplugging the unit from the outlet, pull directly on the plug. Never pull on the power cord.

2. Remove the ice storage basket.

3. Drain remaining water from unit. Remove the cap, then the rubber plug from the spout. When assembling back together, the rubber plug must be inserted first into the spout, and then capped. Otherwise, the ice maker will leak. m

4. Use a mild detergent diluted in warm water and wipe with a soft towel or sponge.
   Solvents, detergents and abrasives must never be used for cleaning.

5. Wipe the inner parts, such as the ice storage basket, water reservoir, water box, ice pusher, and evaporator rods.

6. The outside of the appliance should be cleaned regularly with a mild detergent solution, warm water, and a soft cloth.

7. Dry the interior and exterior with a soft cloth.

8. To begin making ice once the unit has been cleaned, pour clean water into the water reservoir and fill up to the level line follow operating instructions.
   Never tilt or place the appliance on its side, otherwise you must wait 10 hours for compressor coolant to settle.

9. To ensure the cleanliness of the ice cubes, the water in the water storage tank should be replaced every 24 hours.

10. When the machine is not in use or will not be used for an extended period of time, unscrew the drain cap, then remove the rubber plug behind the unit to empty the remaining water in the water reservoir completely. (Follow the instructions in number 3 above.)

TROUBLESHOOTING GUIDE

“ADD WATER”

indicator light turns on.

| ****

Low water level or lack of water.

| Add water and the ice maker will operate automatically.
There is no indication on the control panel.| ****

Disconnection of plug.

| Check that the plug is plugged into the electrical outlet.

“Ice Full” and “Add Water” indicators light up simultaneously.

| ****

Electrical Power Surge or

There may be air in the  lines  or the lines are blocked. The water tank cannot detect water level.

| Turn off the ice maker, pull  out the electric plug, fill it with water   if needed, replace the plug and then restart the unit. or

Inspect relative parts; remove the drain cap on the back of the unit and drain out a small amount of water. Replace the

drain cap and attempt to use the unit again.

or

Check if ice is blocking the ice pusher. Turn off the unit; let the ice melt and restart. Otherwise, call Customer Service at the number below.

The “Ice Full” indicator light is on.| ****

The ice basket is full.

| Remove ice from the ice storage basket to make more.

The unit does not operate.

| ****

Power is not being supplied to the unit. The ambient temperature or the water temperature is too high.

| Plug the unit into a standard 110/120 Volt, 60 Hertz power source. Please run the appliance in temperatures below 90°F and/or pour colder water into the water reservoir.

Ice blockage. No ice is being made.

| ****

Making ice takes too much time.

| Turn off the machine. Start the machine after the ice block melts. Or change the size selector to smaller ice cubes.
The icemaking cycle seems normal but no ice is produced.| There is refrigerant leakage. A pipe in the cooling system is blocked.| Consult a qualified technician or call Customer Service at the number below.

Note: There is protective circuitry inside this appliance to protect the circuitry from overheating. The appliance will automatically shut down to prevent damage if activated. Please disconnect power cord and restart after 30 minutes of cooling down time.

For CURTIS Customer Service, please call: 1-800-968-9853

WARRANTY

Thank you for purchasing this CURTIS product. These products have been made to demanding, high-quality standards and are guaranteed for domestic use against manufacturing faults for a period of 12 months from the date of purchase. This warranty does not affect your statutory rights.
For service within the warranty period, please contact the store where the product was purchased. Product model number and proof of purchase are required for any service request. CURTIS reserves the right to repair or replace the defective product, at its discretion. For any other question, please call our toll-free service line at 1-800-968-9853, Monday to Friday from 8 AM to 6 PM, Eastern time. Normal wear and tear, including accessory wear, is not covered under this warranty. The product is guaranteed for 12 months if used for normal trade purposes, and is valid for the original buyer only. Any warranty is deemed invalid if the product has been overloaded or used improperly, or subject to neglect or attempted repairs other than by an authorized agent. Heavy-duty, daily professional or hire usage are not guaranteed. CURTIS is not responsible for any costs related to labour, injuries or any other loss incurred during the product installation, repair or replacement, including any indirect or consequential damages. Due to continuous product improvement, we reserve the right to change the product specifications without prior notice. Igloo® and Igloo logo are trademarks of Igloo Products Corp. and used by Curtis International Ltd under license. Curtis International Ltd., 315 Attwell Drive, Toronto, Ontario, Canada.

References

• Manual-Hub.com – Free PDF manuals!

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>