KLEIN TOOLS AEPJS3A Bluetooth Speaker with Magnet and Hook Instructions

: June 16, 2024
: KLEIN TOOLS

Table of Contents

KLEIN TOOLS AEPJS3A Bluetooth Speaker with Magnet and Hook
Product Information
Product Usage Instructions
CONTENTS
SYMBOLS ON PRODUCT
OPERATING INSTRUCTIONS
OPERATING INSTRUCTIONS
MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

KLEIN TOOLS AEPJS3A Bluetooth Speaker with Magnet and Hook

KLEIN-TOOLS-AEPJS3A-Bluetooth-Speaker-with-Magnet-and-Hook-
PRODUCT

Product Information

Specifications

Model : Klein Tools AEPJS3A
Power Source : Built-in rechargeable battery
Compatibility: Smart phones, tablets, computers, and other audio devices
Charging Capability : Common mobile devices such as cell phones, tablets, headphones, and smaller USB devices

Product Usage Instructions

Powering On/Off the Speaker:

To turn on the Klein Tools AEPJS3A speaker, press and hold the power button located on the side of the speaker until the LED indicator lights up. To power off, repeat the same process.

Pairing with Audio Devices

To connect the speaker to your audio device via Bluetooth, follow these steps:

Ensure that the speaker is turned on and in Bluetooth pairing mode. The LED indicator will flash rapidly.
On your audio device, enable Bluetooth and search for available devices.
Select “Klein Tools AEPJS3A” from the list of available devices.
If prompted, enter the provided PIN code to complete the pairing process.
Once connected, the LED indicator on the speaker will stop flashing and remain solid.

Charging Mobile Devices

The AEPJS3A speaker can be used to charge your mobile devices. Follow these steps:

Connect your device to the speaker using a compatible USB cable.
Ensure that the speaker is turned on and has enough battery power.
The speaker will automatically detect the connected device and start charging.
Monitor the charging progress on your device’s screen.
Once fully charged, disconnect the device from the speaker.

FAQ

Q: Can the AEPJS3A speaker play music directly from a USB drive?
- A : No, the AEPJS3A speaker does not have a USB port for direct playback from a USB drive. It relies on Bluetooth or wired connections to play audio.
Q: How long does it take to fully charge the built-in battery?
- A : The charging time may vary depending on the remaining battery level, but it generally takes around 2-3 hours to fully charge the AEPJS3A speaker.
Q: What is the range of the Bluetooth connection?
- A : The Bluetooth range of the AEPJS3A speaker is approximately 33 feet (10 meters) in an open space without obstructions. Therange may be shorter if there are walls or other obstacles between the speaker and your audio device.
Q: Can I use the speaker while it is being charged?
- A : Yes, you can use the AEPJS3A speaker while it is being charged. However, please note that charging may take longer if the speaker is in use.
Klein Tools AEPJS3A is a powered speaker designed to provide highquality sound for smart phones, tablets, computers, or other audio devices. The AEPJS3A will also charge common mobile devices like cell phones, tablets, headphones, and other smaller USB devices

Dimensions: 5.46″ × 5.39″ × 2.34″ (139 × 137 × 59 mm) • Weight: 1.4 lb. (635g)
Bluetooth® Version : 4.2
Bluetooth® Connection Range : 100 ft. (30 m) in open space
Support Profiles : AD2P, AVRCP, HFP, SPP
Battery Type : Internal, Li-Ion, 3.63V / 5200mAh (18.88Wh)
Battery Life : 20+ hours at 70% volume
Daisy-Chain Range : 30′ (9 m) in open space
Operating/Charging Temperature : 32° to 104°F (0° to 40°C)
Storage Temperature : -22° to 140°F (-30° to 60°C)
Relative Humidity : <85% non-condensing
Drop Protection: 6.6′ (2 m)
Ingress Protection (IP) Rating : IP54
Certifications : CE, UKCA, FCC, IC, DOE/CEC, NRCAN, NOM

WARNINGS

Read, understand, and follow these instructions to ensure safe operation. Failure to observe these warnings can result in risk of fire or electric shock. Keep these instructions for future reference.

DO NOT use the product if it is damaged or modified. Damaged or modified batteries may exhibit unpredictable behavior resulting in fire, explosion or injury.
Risk of fire and burns. DO NOT open, crush, heat above specified maximum temperature or incinerate. Prolonged exposure to direct sunlight can result in elevated temperatures.
DO NOT immerse in water or other liquids. Properly seal the charging port cover to achieve specified water & foreign object ingress protection. Keep seal free of dirt, oil, sand, or other material that interferes with proper sealing. Failure to do so can result in risk of fire or electric shock.
DO NOT open the charging port cover if wet or in a wet environment.
- Thoroughly dry the unit and the seal around water-resistant cover completely before opening water resistant cover.
DO NOT subject to impacts or drops greater than 6.6′ (2 m).
Drops larger than this may not show signs of damage, but internal components may have been compromised. It is advisable to replacethe unit if any such severe events occur.
DO NOT attempt to repair the product or charging cable. There are no user-serviceable parts.
Specifications subject to change.

SYMBOLS ON PRODUCT

FEATURE DETAILS (FIG.A)

Power Button
Skip Backward Button
Play/Pause/Talk Button
Skip Forward Button
Broadcast Button
*-” Volume Down Button
“+” Volume Up Button
Voice Control Button
Bluetooth® LED Indicator
Battery Status Indicator
Broadcast LED Indicator
Nail Hook
Magnets (×2)
Auxiliary “Aux In” Jack
USB-A Charge Out Port
USB-C Charge In/Out Port
Water/Dust-Resistant Cover

OPERATING INSTRUCTIONS

CHARGING BATTERY

NOTE : Fully charge the speaker before use. First-time charge should be at least 4 hours.
Connect the USB Type C cable connection to USB-Charging port 16; plug the other end of cable to the computer or USB-AC adapter or other USB Avers. Hours: 50-10 Farger: Aprox Hours The bather level indicator will illuminate to indicate charging status (see table below).
ON/OFF : Press & hold power button 1 for 3 seconds, a tone will sound. The unit will automatically power off after 20 minutes of inactivity.
NOTE : Turn unit off when not in use to prolong battery life.
PAIRING : Wireless connection activates automatically and is ready to pair when unit is turned on. On your Bluetooth® wireless compatible device,enable Bluetooth® and search/scan for devices that can be paired. Select “AEPJS3A” when it appears (refer to the user manual of your device). Ifnecessary, enter “0000” as pairing passcode. A tone sounds after a successful pairing.
NOTE : Unit automatically attempts to connect the last paired wireless device but is ready to pair with any compatible device if the last paired device is not detected within 5 seconds of powering on.

DISCONNECT CURRENT PAIRING:

Turn unit off, -OR2.Single-press Power Button 1 . Bluetooth® LED Indicator 9 will blink, -OR3.Plug a cable into AUX jack 14 , -OR4.Turn off Bluetooth® wireless connection in paired device.

PAIRING DIFFERENT DEVICES :

Single-press Power Button 1 (tone sounds twice) to re-enter pairing mode.
Follow the instructions in the PAIRING section to pair with a different device. RESET WIRELESS CONNECTION:
Double-press Power Button 1 (tone sounds once) to to clear the Bluetooth pairing list.
Follow instructions in the PAIRING section to pair with new devices (a new pairing list will be created)

OPERATING INSTRUCTIONS

PLAYING AUDIO : Use your device to control the speaker or use the built-in control buttons on the speaker.
Press the Play/Pause/Talk button 3 to play or pause audio on your device.
Press the “-” 6 or “+” 7 button to adjust the speaker volume. A tone will sound when maximum volume is reached. Volume may also be controlled from your audio device.
Press the Skip Forward 4 or Skip Backward 2 buttons to skip backward or forward (respectively) during a song.
AUXILIARY AUDIO-IN : Connect one end of the auxiliary cable to the AUX jack 14 of the speaker; plug the other end of cable to line-out or headphone jack of your device.
SPEAKERPHONE OPERATION:
When an incoming call occurs, playing music is muted & ring tone sounds. Shortpress Play/Pause/Talk 3 button to answer the call, or long-press to ignore.
To disconnect the call, short press the Play/Pause/Talk button 3 to hang up.

BROADCAST: Once you have successfully connected your AEPJS3A speaker to a Bluetooth ® device, you can connect up to four* more AEPJS3A speakers to your already connected AEPJS3A speaker.

Ensure your primary AEPJS3A speaker is turned on, this will be your Source speaker.
Press the Broadcast button
once or until “SOURCE” is heard. LED will turn solid white.
The Source speaker will broadcast a signal for three minutes, then time out. To reset the timer, press and hold the Broadcast button for three seconds.
Power on any additional AEPJS3A speakers (up to four*) and press the Broadcast button 5 twice or until “SYNCING” is heard. LED will flash green. 5. Position the Syncing speakers near the Source speaker. Allow up to ten seconds for the speakers to link with each other. Upon successful connection, the synced speakers ’ LEDs will turn solid green, and “SYNCED” will be heard.

NOTE :

When cycling through the Broadcast menu, three different modes will be heard, “Solo”, “Source” and “Syncing” each are described below:
- “ SOLO “: Standalone mode, speaker is not in Broadcast mode.
- “ SOURCE”: Is the primary speaker to which secondary speakers link.
- “ SYNCING”: Secondary or satellite speakers to that connects to the primary speaker.
The maximum range between speakers is 30′ (10m) he broadcast connection between all speakers will NOT automatically reconnect after the speaker are turned off. To reconnect, follow the Broadcast steps above.
Up to seven additional speakers can be connected, but for optimal performance link no more than four speakers.

VOICE CONTROL: Press the voice control button 8 to activate the voice assistant on your device.

NOTE : Before using this function, the devices must be connected to the speaker via Bluetooth ®
LOW BATTERY INDICATION : The Red LED on the Battery Status Indicator 10 will flash on/off when battery level drops to approximately 5%. Speaker will automatically power off when the battery level is below 2%. Recharge speaker as soon as possible.

POSITIONING SPEAKER:

Make sure that the front of the speaker is not obstructed.
Stand the speaker upright on a flat, level, stable surface. •
Attach the speaker to a metal surface via the magnets 13 on the back of the unit.
DO NOT mount to electrical equipment.
Hang from a nail (or like item) by opening the Nail Hook 12 and placing the
Nail Hook over the head of the nail.

CHARGING DEVICES

NOTE : For best results, use cable provided with your device.

Connect the cable to your device.
Connect the charging cable to the USB A Charge Out Port 15 or USB C Charge In/Out Port 16. Your device will automatically begin charging. The device being charged should provide indication that charging has begun.
Press and hold the Power button 1 for 3 seconds to turn on the Mspeaker; your device will begin charging.
Press and hold the Power button 1 again for 3 seconds and all functions will power off; your device will stop charging.
When AEPJS3A is in Charge-Out-Only mode, it will automatically shut down once charging is complete and current is no longer being drawn by the device.
Repeat these steps to charge another device

COMPLIANCE

FCC COMPLIANCE

This device complies with part 15 of the FCC Rules and Industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions:

this device may not cause harmful interference, and
this device must accept any interference received,including interference that may cause undesired operation.

NOTE : The grantee is not responsible for any changes or modifications not expressly approved by the party responsible for compliance. Such modifications could void the user’s authority to operate the equipment.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

Reorient or relocate the receiving antenna.
Increase the separation between the equipment and receiver.
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for help

FCC RF EXPOSURE STATEMENTS:

This transmitter must not be co‐located or operated in conjunction with any other antenna or transmitter.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with a minimum distance of 5mm between the radiator and your body or nearby persons.

IC NOTICE TO CANADIAN USERS

This device complies with industry Canada license-exempt RSS standard(s). Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation of the device. This device complies with RSS-247 of Industry Canada. Operation is subject to the condition that this device does not cause harmful interference. This Class B digital apparatus complies with Canadian ICES-003.

IC RADIATION EXPOSURE STATEMENT:

This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 5mm between the radiator and your body.

I FEEL REPORT

For use in Mexico, the operation of this equipment is subject to the following two conditions

This equipment or device does not cause harmful interference and
this equipment or device accepts any interference, including that which can cause undesired operation.

EU DECLARATION OF CONFORMITY

Hereby, Klein Tools declares that this product is in compliance with Directive 2014/53/EU and all other applicable EU requirements. The complete declaration of conformity can be found on this product’s page at www.kleintools.com UKCA DECLARATION OF CONFORMITY
Hereby, Klein Tools declares that this product is in compliance with the relevant statutory requirements. The complete declaration of conformity can be found on this product’s page at www.kleintools.com

MAINTENANCE

CLEANING: Be sure the speaker is turned off and wipe with a clean, dry lint-free cloth. Do not use abrasive cleaners or solvents.
STORAGE : If the speaker is to be left unused for an extended period of time, charge before storing, and recharge periodically during storage, to maintain the battery’s charging capacity

WARRANTY

www.kleintools.com/warranty

DISPOSAL / RECYCLE

Do not place equipment and its accessories in the trash. Items must be properly disposed of in accordance with local regulations. Please see www.epa.gov/recycle for additional information.
The Bluetooth® word mark and logos are registered trademarks owned by Bluetooth® SIG, Inc. and any use of such marks by Klein Tools. Inc. is under license.

CUSTOMER SERVICE

KLEIN TOOLS, INC.