makita DG Series Cordless Angle Grinder Instruction Manual

June 16, 2024
Makita

makita DG Series Cordless Angle Grinder

Product Information

Specifications

  • Model: DGA405, DGA455, DGA505
  • Wheel diameter: 100 mm (4″) for DGA405, 115 mm (4-1/2″) for DGA455, 125 mm (5″) for DGA505
  • Max. wheel thickness: 6 mm (1/4″)
  • Spindle thread: M10 for DGA405, M14 or 5/8 (country-specific) for DGA455 and DGA505
  • Rated speed (n): 8,500 min-1
  • No load speed (n0): Not specified
  • Overall length: 348 mm for DGA405, 362 mm for DGA455 and DGA505
  • Net weight: 2.2 kg (with BL1815N, BL1820 battery cartridge) for DGA405, 2.3 kg (with BL1830, BL1840, BL1850 battery cartridge) for DGA455, 2.4 kg (with BL1815N, BL1820 battery cartridge) for DGA405, 2.5 kg (with BL1830, BL1840, BL1850 battery cartridge) for DGA505
  • Rated voltage: DC 18V

Intended Use
The tool is intended for grinding, sanding, and cutting of metal and stone materials without the use of water.

Product Usage Instructions

General Power Tool Safety Warnings
Read all safety warnings and instructions. Failure to follow the warnings and instructions may result in electric shock, fire, and/or serious injury. Save all warnings and instructions for future reference.

Cordless Grinder Safety Warnings
Safety Warnings Common for Grinding, Sanding, Wire Brushing, or Abrasive Cutting-Off Operations:

  1. This power tool is intended to function as a grinder, sander, wire brush, or cut-off tool. Read all safety warnings, instructions, illustrations, and specifications provided with this power tool.
  2. Do not operate this power tool near flammable materials.
  3. Do not use accessories that are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool does not mean it should be used.
  4. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.
  5. The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.
  6. The threaded mounting of accessories must match the grinder spindle thread. Use only accessories with a matching thread.
  7. Inspect accessories for any damage before each use. Do not use accessories that are cracked, chipped, or have missing segments.
  8. Ensure the switch is in the off-position before connecting to a power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energizing power tools that have the switch on invites accidents.
  9. Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
  10. Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.

Kickback Warning
Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

  • Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use an auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up.
  • Ensure the wheel is not contacting the workpiece before the switch is turned on. The wheel may bind, causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on the direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.

FAQ

  • Q: What is the intended use of the cordless angle grinder?
    A: The tool is intended for grinding, sanding, and cutting metal and stone materials without the use of water.

  • Q: What are the safety precautions for using the cordless angle grinder?
    A: Some safety precautions include reading all safety warnings and instructions, using accessories recommended by the manufacturer, checking the speed rating of accessories, inspecting accessories for damage, and maintaining proper grip and balance to avoid kickback.

Explanation of general view

  1. Button
  2. Red indicator
  3. Battery cartridge
  4. Lock-off lever
  5. Switch lever
  6. Battery indicator
  7. Mode indicator
  8. Shaft lock
  9. Wheel guard
  10. Bearing box
  11. Screw
  12. Lever
  13. Lock nut
  14. Depressed center wheel
  15. Inner flange
  16. Lock nut wrench
  17. Ezynut
  18. Abrasive wheel
  19. Spindle
  20. Arrow
  21. Notch
  22. Flex wheel
  23. Plastic pad
  24. Sanding lock nut
  25. Abrasive disc
  26. Rubber pad
  27. Abrasive cut-off wheel/diamond wheel
  28. Wheel guard for abrasive cut-off wheel/diamond wheel
  29. Abrasive cut-off wheel
  30. Diamond wheel
  31. Thickness: Less than 4 mm (5/32”)
  32. Thickness: 4 mm (5/32”) or more
  33. Wire cup brush
  34. Wire wheel brush
  35. Exhaust vent
  36. Inhalation vent
  37. Dust cover

SPECIFICATIONS

Model DGA405 DGA455 DGA505
Wheel diameter 100 mm (4”) 115 mm (4-1/2”) 125 mm (5”)
Max. wheel thickness 6 mm (1/4”) 6 mm (1/4”) 6 mm (1/4”)
Spindle thread M10 M14 or 5/8” (country-specific)
Rated speed (n)/No load speed (n0) 8,500 min-1
Overall length With battery cartridge BL1815N, BL1820 348 mm
With battery cartridge BL1830, BL1840, BL1850 362 mm
Net weight With battery cartridge BL1815N, BL1820 2.2 kg 2.3 kg
With battery cartridge BL1830, BL1840, BL1850 2.4 kg 2.5 kg 2.6 kg
Rated voltage D.C. 18V
  • Due to our continuing program of research and development, the specifications herein are subject to change without notice.
  • Specifications and battery cartridges may differ from country to country.
  • Weight, with battery cartridge, according to EPTA-Procedure 01/2003

Intended use
The tool is intended for grinding, sanding and cutting of metal and stone materials without the use of water.

General Power Tool Safety Warnings

WARNING
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

CORDLESS GRINDER SAFETY WARNINGS

Safety Warnings Common for Grinding, Sanding, Wire Brushing, or Abrasive Cutting-Off Operations:

  1. This power tool is intended to function as a grinder, sander, wire brush or cut-off tool. Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.

  2. Operations such as polishing are not recommended to be performed with this power tool. Operations for which the power tool was not designed may create a hazard and cause personal injury.

  3. Do not use accessories that are not specifically designed and recommended by the tool manufacturer. Just because the accessory can be attached to your power tool, it does not assure safe operation.

  4. The rated speed of the accessory must be at least equal to the maximum speed marked on the power tool. Accessories running faster than their rated speed can break and fly apart.

  5. The outside diameter and the thickness of your accessory must be within the capacity rating of your power tool. Incorrectly sized accessories cannot be adequately guarded or controlled.

  6. The threaded mounting of accessories must match the grinder spindle thread. For accessories mounted by flanges, the arbour hole of the accessory must fit the locating diameter of the flange. Accessories that do not match the mounting hardware of the power tool will run out of balance, vibrate excessively and may cause loss of control.

  7. Do not use a damaged accessory. Before each use inspect the accessories such as abrasive wheels for chips and cracks, backing pad for cracks, tear or excess wear, and wire brush for loose or cracked wires. If a power tool or accessory is dropped, inspect for damage or install an undamaged accessory. After inspecting and installing an accessory, position yourself and bystanders away from the plane of the rotating accessory and run the power tool at maximum no-load speed for one minute. Damaged accessories will normally break apart during this test time.

  8. Wear personal protective equipment. Depending on the application, use a face shield, safety goggles or safety glasses. As appropriate, wear a dust mask, hearing protectors, gloves and a workshop apron capable of stopping small abrasive or workpiece fragments. The eye protection must be capable of stopping flying debris generated by various operations. The dust mask or respirator must be capable of filtrating particles generated by your operation. Prolonged exposure to high-intensity noise may cause hearing loss.

  9. Keep bystanders a safe distance away from the work area. Anyone entering the work area must wear personal protective equipment. Fragments of workpieces or of a broken accessory may fly away and cause injury beyond the immediate area of operation.

  10. Hold the power tool by insulated gripping surfaces only, when performing an operation where the cutting tool may contact hidden wiring. Contact with a “live” wire will also make exposed metal parts of the power tool “live” and could give the operator an electric shock.

  11. Never lay the power tool down until the accessory has come to a complete stop. The spinning accessory may grab the surface and pull the power tool out of your control.

  12. Do not run the power tool while carrying it at your side. Accidental contact with the spinning accessory could snag your clothing, pulling the accessory into your body.

  13. Regularly clean the power tool’s air vents. The motor’s fan will draw dust inside the housing and excessive accumulation of powdered metal may cause electrical hazards.

  14. Do not operate the power tool near flammable materials. Sparks could ignite these materials.

  15. Do not use accessories that require liquid coolants. Using water or other liquid coolants may result in electrocution or shock.
    Kickback and Related Warnings
    Kickback is a sudden reaction to a pinched or snagged rotating wheel, backing pad, brush or any other accessory. Pinching or snagging causes rapid stalling of the rotating accessory which in turn causes the uncontrolled power tool to be forced in the direction opposite of the accessory’s rotation at the point of the binding.
    For example, if an abrasive wheel is snagged or pinched by the workpiece, the edge of the wheel that is entering into the pinch point can dig into the surface of the material causing the wheel to climb out or kick out. The wheel may either jump toward or away from the operator, depending on the direction of the wheel’s movement at the point of pinching. Abrasive wheels may also break under these conditions.
    Kickback is the result of power tool misuse and/or incorrect operating procedures or conditions and can be avoided by taking proper precautions as given below.

    • Maintain a firm grip on the power tool and position your body and arm to allow you to resist kickback forces. Always use an auxiliary handle, if provided, for maximum control over kickback or torque reaction during start-up. The operator can control torque reactions or kickback forces if proper precautions are taken.

    • Never place your hand near the rotating accessory. The accessory may kick back over your hand.

    • Do not position your body in the area where the power tool will move if kickback occurs. Kickback will propel the tool in a direction opposite to the wheel’s movement at the point of snagging.

    • Use special care when working corners, sharp edges etc. Avoid bouncing and snagging the accessory. Corners, sharp edges or bouncing tend to snag the rotating accessory and cause loss of control or kickback.

    • Do not attach a saw chain woodcarving blade or toothed saw blade. Such blades create frequent kickbacks and loss of control.
      Safety Warnings Specific for Grinding and Abrasive Cutting-Off Operations:

    • Use only wheel types that are recommended for your power tool and the specific guard designed for the selected wheel. Wheels for which the power tool was not designed cannot be adequately guarded and are unsafe.

    • The grinding surface of centre-depressed wheels must be mounted below the plane of the guard lip. An improperly mounted wheel that projects through the plane of the guard lip cannot be adequately protected.

    • The guard must be securely attached to the power tool and positioned for maximum safety so that the least amount of wheel is exposed towards the operator. The guard helps to protect the operator from broken wheel fragments, accidental contact with the wheel and sparks that could ignite clothing.

    • Wheels must be used only for recommended applications. For example: do not grind with the side of the cut-off wheel. Abrasive cut-off wheels are intended for peripheral grinding, side forces applied to these wheels may cause them to shatter.

    • Always use undamaged wheel flanges that are of the correct size and shape for your selected wheel. Proper wheel flanges support the wheel thus reducing the possibility of wheel breakage. Flanges for cut-off wheels may be different from grinding wheel flanges.

    • Do not use worn-down wheels from larger power tools. The wheel intended for a larger power tool is not suitable for the higher speed of a smaller tool and may burst.
      Additional Safety Warnings Specific for Abrasive Cutting-Off Operations:

    • Do not “jam” the cut-off wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback or wheel breakage.

    • Do not position your body in line with and behind the rotating wheel. When the wheel, at the point of operation, is moving away from your body, the possible kickback may propel the spinning wheel and the power tool directly at you.

    • When the wheel is binding or when interrupting a cut for any reason, switch off the power tool and hold the power tool motionless until the wheel comes to a complete stop. Never attempt to remove the cut-off wheel from the cut while the wheel is in motion otherwise kickback may occur. Investigate and take corrective action to eliminate the cause of wheel binding.

    • Do not restart the cutting operation in the workpiece. Let the wheel reach full speed and carefully re-enter the cut. The wheel may bind, walk up or kick back if the power tool is restarted in the workpiece.

    • Support panels or any oversized workpiece to minimize the risk of wheel pinching and kickback. Large workpieces tend to sag under their own weight. Supports must be placed under the workpiece near the line of cut and near the edge of the workpiece on both sides of the wheel.

    • Use extra caution when making a “pocket cut” into existing walls or other blind areas. The protruding wheel may cut gas or water pipes, electrical wiring or objects that can cause kickback.
      Safety Warnings Specific for Sanding Operations:
      Do not use excessively oversized sanding disc paper. Follow the manufacturer’s recommendations, when selecting sanding paper. Larger sanding paper extending beyond the sanding pad presents a laceration hazard and may cause snagging, tearing of the disc or kickback.
      Safety Warnings Specific for Wire Brushing Operations:

    • Be aware that wire bristles are thrown by the brush even during ordinary operation. Do not overstress the wires by applying excessive load to the brush. The wire bristles can easily penetrate light clothing and/or skin.

    • If the use of a guard is recommended for wire brushing, do not allow interference of the wire wheel or brush with the guard. Wire wheel or brush may expand in diameter due to workload and centrifugal forces.
      Additional Safety Warnings:

  16. When using depressed centre grinding wheels, be sure to use only fiberglass-reinforced wheels.

  17. NEVER USE Stone Cup-type wheels with this grinder. This grinder is not designed for these types of wheels and the use of such a product may result in serious personal injury.

  18. Be careful not to damage the spindle, the flange (especially the installing surface) or the lock nut. Damage to these parts could result in wheel breakage.

  19. Make sure the wheel is not contacting the workpiece before the switch is turned on.

  20. Before using the tool on an actual workpiece, let it run for a while. Watch for vibration or wobbling that could indicate poor installation or a poorly balanced wheel.

  21. Use the specified surface of the wheel to perform the grinding.

  22. Do not leave the tool running. Operate the tool only when hand-held.

  23. Do not touch the workpiece immediately after the operation; it may be extremely hot and could burn your skin.

  24. Observe the instructions of the manufacturer for correct mounting and use of wheels. Handle and store wheels with care.

  25. Do not use separate reducing bushings or adaptors to adapt large-hole abrasive wheels.

  26. Use only the flanges specified for this tool.

  27. For tools intended to be fitted with threaded hole wheels, ensure that the thread in the wheel is long enough to accept the spindle length.

  28. Check that the workpiece is properly supported.

  29. Pay attention that the wheel continues to rotate after the tool is switched off.

  30. If the working place is extremely hot and humid, or badly polluted by conductive dust, use a short-circuit breaker (30 mA) to assure operator safety.

  31. Do not use the tool on any materials containing asbestos.

  32. When using the cut-off wheel, always work with the dust-collecting wheel guard required by domestic regulations.

  33. Cutting discs must not be subjected to any lateral pressure.

SAVE THESE INSTRUCTIONS.

WARNING:
DO NOT let comfort or familiarity with the product (gained from repeated use) replace strict adherence to safety rules for the subject product. MISUSE or failure to follow the safety rules stated in this instruction manual may cause serious personal injury.

IMPORTANT SAFETY INSTRUCTIONS

FOR BATTERY CARTRIDGE

  1. Before using the battery cartridge, read all instructions and cautionary markings on (1) battery charger, (2) battery, and (3) product using the battery.

  2. Do not disassemble the battery cartridge.

  3. If operating time has become excessively shorter, stop operating immediately. It may result in a risk of overheating, possible burns and even an explosion.

  4. If electrolyte gets into your eyes, rinse them out with clear water and seek medical attention right away. It may result in loss of your eyesight.

  5. Do not short the battery cartridge:

  6. Do not touch the terminals with any conductive material.

  7. Avoid storing battery cartridges in a container with other metal objects such as nails, coins, etc.

  8. Do not expose the battery cartridge to water or rain.
    A battery short can cause a large current flow, overheating, possible burns and even a breakdown.

  9. Do not store the tool and battery cartridge in locations where the temperature may reach or exceed 50°C (122°F).

  10. Do not incinerate the battery cartridge even if it is severely damaged or is completely worn out. The battery cartridge can explode in a fire.

  11. Be careful not to drop or strike the battery.

  12. Do not use a damaged battery.

  13. Follow your local regulations relating to the disposal of batteries.

SAVE THESE INSTRUCTIONS.

Tips for maintaining maximum battery life

  1. Charge the battery cartridge before completely discharged.
    Always stop tool operation and charge the battery cartridge when you notice less tool power.

  2. Never recharge a fully charged battery cartridge. Overcharging shortens the battery service life.

  3. Charge the battery cartridge at room temperature at 10°C – 40°C (50°F – 104°F). Let a hot battery cartridge cool down before charging it.

  4. Charge the battery cartridge once in every six months if you do not use it for a long period.

FUNCTIONAL DESCRIPTION

CAUTION:
Always be sure that the tool is switched off and the battery cartridge is removed before adjusting or checking the function on the tool.

Installing or removing the battery cartridge (Fig. 1)

CAUTION:

  • Always switch off the tool before installing or removing of the battery cartridge.
  • Hold the tool and the battery cartridge firmly when installing or removing the battery cartridge. Failure to hold the tool and the battery cartridge firmly may cause them to slip off your hands and result in damage to the tool and battery cartridge and a personal injury.

To remove the battery cartridge, slide it from the tool while sliding the button on the front of the cartridge. To install the battery cartridge, align the tongue on the battery cartridge with the groove in the housing and slip it into place. Insert it all the way until it locks in place with a little click. If you can see the red indicator on the upper side of the button, it is not locked completely.

CAUTION:

  • Always install the battery cartridge fully until the red indicator cannot be seen. If not, it may accidentally fall out of the tool, causing injury to you or someone around you.
  • Do not install the battery cartridge forcibly. If the cartridge does not slide in easily, it is not being inserted correctly.

Switch action

CAUTION:

  • Before installing the battery cartridge into the tool, always check to see that the switch lever actuates properly and returns to the “OFF” position when released.
  • Do not pull the switch lever hard without pulling the lock-off lever. This can cause switch breakage.

To prevent the switch lever from being accidentally pulled, a lock-off lever is provided. To start the tool, pull the lock-off lever toward the operator and then pull the switch lever. Release the switch lever to stop. (Fig. 2)

Accidental re-start preventive function

  • Even if installing the battery cartridge while pulling the switch lever, the tool does not start.
  • To start the tool, first release the switch lever. Then pull the lock-off lever and then pull the switch lever.

Indicating remaining battery capacity (Fig. 3)

  • When you turn the tool on, the battery indicator shows the remaining battery capacity.
  • The remaining battery capacity is shown in the following table.

Automatic speed change function (Fig. 4)

This tool has “high-speed mode” and “high torque mode”. It automatically changes operation mode depending on the workload. When the mode indicator lights up during operation, the tool is in high torque mode.

Tool/battery protection system

  • The tool is equipped with a tool/battery protection system. This system automatically cuts off power to the motor to extend tool and battery life.
  • The tool will automatically stop during operation if the tool or battery is placed under one of the following conditions. In some conditions, the indicator lights up.

Overload protection
When the tool is operated in a manner that causes it to draw an abnormally high current, the tool automatically stops without any indications. In this situation, turn the tool off and stop the application that caused the tool to become overloaded. Then turn the tool on to restart.

Overheat protection for tool
When the tool is overheated, the tool stops automatically and the battery indicator shows the following state. In this situation, let the tool cool before turning the tool on again.

Releasing protection lock
When the protection system works repeatedly, the tool is locked and the battery indicator shows the following state.

In this situation, the tool does not start even if turning the tool off and on. To release the protection lock, remove the battery, set it to the battery charger and wait until the charging finishes.

Shaft lock

CAUTION:
Never actuate the shaft lock when the spindle is moving. The tool may be damaged.

Press the shaft lock to prevent spindle rotation when installing or removing accessories. (Fig. 5)

ASSEMBLY

CAUTION:
Always be sure that the tool is switched off and the battery cartridge is removed before carrying out any work on the tool.

Installing side grip (handle)

CAUTION:

  • Always be sure that the side grip is installed securely before operation.
  • Screw the side grip securely on the position of the tool as shown in the figure. (Fig. 6)

Installing or removing wheel guard (For depressed centre wheel, flap disc/abrasive cut-off wheel, diamond wheel)

WARNING:

  • When using a depressed centre grinding wheel/flap disc, flex wheel, wire wheel brush, cut-off wheel or diamond wheel, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
  • When using an abrasive cut-off/diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. (In some European countries, when using a diamond wheel, the ordinary guard can be used. Follow the regulations in your country.)

For tool with clamp lever type wheel guard
Loosen the lever on the wheel guard after loosening the screw. Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard to such an angle that it can protect the operator according to work. (Fig. 7) Tighten the lever to fasten the wheel guard. If the lever is too tight or too loose to fasten the wheel guard, loosen or tighten the screw to adjust the tightening of the wheel guard band. (Fig. 8)

To remove the wheel guard, follow the installation procedure in reverse.

For tools with locking screw-type wheel guards (Fig. 9)
Mount the wheel guard with the protrusion on the wheel guard band aligned with the notch on the bearing box. Then rotate the wheel guard to such an angle that it can protect the operator according to work. Be sure to tighten the screw securely.

To remove the wheel guard, follow the installation procedure in reverse.

Installing or removing the depressed centre wheel or flap disc (optional accessory)

WARNING:

  • When using a depressed centre wheel or flap disc, the wheel guard must be fitted on the tool so that the closed side of the guard always points toward the operator.
  • Only actuate the shaft lock when the spindle is not moving.
  • Mount the inner flange onto the spindle.
  • Make sure to fit the dented part of the inner flange onto the straight part at the bottom of the spindle.
  • Fit the wheel/disc on the inner flange and screw the lock nut onto the spindle. (Fig. 10)
  • To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. (Fig. 11)
  • To remove the wheel, follow the installation procedure in reverse.

Installing or removing Ezynut (optional accessory)

CAUTION:
Do not use Ezynut with Super Flange or angle grinder with “F” on the end of model No. Those flanges are so thick that the entire thread cannot be retained by the spindle.

  • Mount the inner flange, abrasive wheel and Ezynut onto the spindle so that the Makita Logo on the Ezynut faces outside. (Fig. 12)
  • Press the shaft lock firmly and tighten Ezynut by turning the abrasive wheel clockwise as far as it turns.
  • Turn the outside ring of Ezynut counterclockwise to loosen. (Fig. 13)

NOTE:
Ezynut can be loosened by hand as long as the arrow points to the notch. Otherwise, a lock nut wrench is required to loosen it. Insert one pin of the wrench into a hole and turn Ezynut counterclockwise. (Fig. 14 & 15)

Installing or removing the flex wheel (optional accessory)

WARNING:
Always use a supplied guard when the flex wheel is on the tool. The wheel can shatter during use and the guard helps to reduce the chances of personal injury. (Fig. 16)

Follow instructions for the depressed center grinding wheel/flap disc but also use a plastic pad over the wheel. See the order of assembly on the accessories page in this manual.

Installing or removing abrasive disc (optional accessory) (Fig. 17)
Mount the rubber pad onto the spindle. Fit the disc on the rubber pad and screw the lock nut onto the spindle. To tighten the lock nut, press the shaft lock firmly so that the spindle cannot revolve, then use the lock nut wrench and securely tighten clockwise. To remove the disc, follow the installation procedure in reverse.

NOTE:
Use sander accessories specified in this manual. These must be purchased separately.

OPERATION

WARNING:

  • It should never be necessary to force the tool. The weight of the tool applies adequate pressure. Forcing and excessive pressure could cause dangerous wheel breakage.
  • ALWAYS replace the wheel if the tool is dropped while grinding.
  • NEVER bang or hit a grinding disc or wheel onto work.
  • Avoid bouncing and snagging the wheel, especially when working corners, sharp edges etc. This can cause loss of control and kickback.
  • NEVER use tools with wood cutting blades and other sawblades. Such blades when used on a grinder frequently kick and cause loss of control leading to personal injury.

CAUTION:

  • Never switch on the tool when it is in contact with the workpiece, it may cause an injury to the operator.
  • Always wear safety goggles or a face shield during operation.
  • After operation, always switch off the tool and wait until the wheel has come to a complete stop before putting the tool down.

Grinding and sanding operation (Fig. 18)
ALWAYS hold the tool firmly with one hand on the housing and the other on the side handle. Turn the tool on and then apply the wheel or disc to the workpiece. In general, keep the edge of the wheel or disc at an angle of about 15 degrees to the workpiece surface. During the break-in period with a new wheel, do not work the grinder in the B direction or it will cut into the workpiece. Once the edge of the wheel has been rounded off by use, the wheel may be worked in both A and B directions.

Operation with abrasive cut-off/diamond wheel (optional accessory) (Fig. 19)
Remove the battery cartridge from the tool and place it upside down allowing easy access to the spindle. Mount the inner flange and abrasive cut- off/diamond wheel onto the spindle. Tighten the lock nut securely with the supplied wrench. The direction for mounting the lock nut and the inner flange varies by wheel thickness. Refer to the table below. (Fig. 20)

WARNING:

  • When using an abrasive cut-off/diamond wheel, be sure to use only the special wheel guard designed for use with cut-off wheels. (In some European countries, when using a diamond wheel, the ordinary guard can be used. Follow the regulations in your country.)
  • NEVER use cut-off wheel for side grinding.
  • Do not “jam” the wheel or apply excessive pressure. Do not attempt to make an excessive depth of cut. Overstressing the wheel increases the loading and susceptibility to twisting or binding of the wheel in the cut and the possibility of kickback, wheel breakage and overheating of the motor may occur.
  • Do not start the cutting operation in the workpiece. Let the wheel reach full speed and carefully enter into the cut moving the tool forward over the workpiece surface. The wheel may bind, walk up or kick back if the power tool is started in the workpiece.
  • During cutting operations, never change the angle of the wheel. Placing side pressure on the cut-off wheel (as in grinding) will cause the wheel to crack and break, causing serious personal injury.
  • A diamond wheel shall be operated perpendicular to the material being cut.

Operation with wire cup brush (optional accessory)

CAUTION:

  • Check the operation of the brush by running the tool with no load, ensuring that no one is in front of or in line with a brush.
  • Do not use a brush that is damaged, or which is out of balance. The use of damaged brush could increase the potential for injury from contact with broken brush wires.

Remove the battery cartridge from the tool and place it upside down allowing easy access to the spindle. Remove any accessories on the spindle. Thread wire cup brush onto the spindle and tighten with the supplied wrench. When using a brush, avoid applying too much pressure which causes the overbending of wires, leading to premature breakage. (Fig. 21)

Operation with wire wheel brush (optional accessory)

CAUTION:

  • Check the operation of the wire wheel brush by running the tool with no load, ensuring that no one is in front of or in line with the wire wheel brush.
  • Do not use a wire wheel brush that is damaged, or which is out of balance. The use of a damaged wire wheel brush could increase the potential for injury from contact with broken wires.
  • ALWAYS use a guard with wire wheel brushes, assuring the diameter of the wheel fits inside the guard. The wheel can shatter during use and the guard helps to reduce chances of personal injury.

Remove the battery cartridge from the tool and place it upside down allowing easy access to the spindle. Remove any accessories on the spindle. Thread wire wheel brush onto the spindle and tighten with the wrenches. (Fig. 22)

When using a wire wheel brush, avoid applying too much pressure which causes overbending of wires, leading to premature breakage.

MAINTENANCE

CAUTION:

  • Always be sure that the tool is switched off and the battery cartridge is removed before attempting to perform inspection or maintenance.
  • Never use gasoline, benzine, thinner, alcohol or the like. Discolouration, deformation or cracks may result.
  • The tool and its air vents have to be kept clean. Regularly clean the tool’s air vents or whenever the vents start to become obstructed. (Fig. 23)
  • Remove the dust cover from the inhalation vent and clean it for smooth air circulation. (Fig. 24)

NOTE:
Clean out the dust cover when it is clogged with dust or foreign matter. Continuing operation with a clogged dust cover may damage the tool.

To maintain product SAFETY and RELIABILITY, repairs, and any other maintenance or adjustment should be performed by Makita Authorized Service Centers, always using Makita replacement parts.

OPTIONAL ACCESSORIES

CAUTION:
These accessories or attachments are recommended for use with your Makita tool specified in this manual. The use of any other accessories or attachments might present a risk of injury to persons. Only use accessory or attachment for its stated purpose.

If you need any assistance with more details regarding these accessories, ask your local Makita Service Center.

  • Makita genuine battery and charger
  100 mm (4”) model 115 mm (4-1/2”) model 125 mm (5”) model
1 Grip 36
2 Wheel guard (for grinding wheel)
3 Inner flange 30 Inner flange 42 Super flange 47 *1 Inner flange 42 Super

flange 47 1
4| Depressed centre wheel/Flap disc
5| Lock nut 10-30| Lock nut 14-45 Ezy nut
2| Lock nut 14-45 Ezy nut 2
6| Plastic pad| Plastic pad| Plastic pad
7| Flex wheel| Flex wheel| Flex wheel
8| Rubber pad 76| Rubber pad 100| Rubber pad 115
9| Abrasive disc
10| Sanding lock nut 10-30| A sanding lock nut 14-48| A sanding lock nut 14-48
11| Wire wheel brush
12| Wire cup brush
13| Wheel guard (for cut-off wheel)
3
14| Abrasive cut-off wheel/Diamond wheel
–| Lock nut wrench 20| Lock nut wrench 35| Lock nut wrench 35

Note:

  1. The super flange needs only 1/3 of the effort to undo the lock nut, compared with the conventional type.
  2. Do not use Super Flange and Ezynut together.
  3. In some European countries, when using a diamond wheel, the ordinary guard can be used instead of the special guard covering both sides of the wheel. Follow the regulations in your country.

NOTE:
Some items in the list may be included in the tool package as standard accessories. They may differ from country to country.

Noise
The typical A-weighted noise level determined according to EN60745:

Model DGA405, DGA455

  • Sound pressure level (LpA): 80 dB (A)
  • Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Model DGA505

  • Sound pressure level (LpA): 79 dB (A)
  • Uncertainty (K): 3 dB (A)

The noise level under working may exceed 80 dB (A).

Wear ear protection.

Vibration
The vibration total value (tri-axial vector sum) determined according to EN60745:

Model DGA405

  • Work mode: surface grinding
  • Vibration emission (ah, AG): 4.5 m/s2
  • Uncertainty (K): 1.5 m/s2
  • Work mode: disc sanding
  • Vibration emission (ah, DS): 2.5 m/s2 or less
  • Uncertainty (K): 1.5 m/s2

Model DGA455

  • Work mode: surface grinding with normal side grip
  • Vibration emission (ah, AG): 5.5 m/s2
  • Uncertainty (K): 1.5 m/s2
  • Work mode: surface grinding with anti-vibration side grip
  • Vibration emission (ah, AG): 5.0 m/s2
  • Uncertainty (K): 1.5 m/s2
  • Work mode: disc sanding
  • Vibration emission (ah, DS): 2.5 m/s2 or less
  • Uncertainty (K): 1.5 m/s2

Model DGA505

  • Work mode: surface grinding with normal side grip
  • Vibration emission (ah, AG): 6.0 m/s2
  • Uncertainty (K): 1.5 m/s2
  • Work mode: surface grinding with anti-vibration side grip
  • Vibration emission (ah, AG): 5.5 m/s2
  • Uncertainty (K): 1.5 m/s2
  • Work mode: disc sanding
  • Vibration emission (ah, DS): 2.5 m/s2 or less
  • Uncertainty (K): 1.5 m/s2
  • The declared vibration emission value has been measured under the standard test method and may be used for comparing one tool with another.
  • The declared vibration emission value may also be used in a preliminary assessment of exposure.
  • The declared vibration emission value is used for the main applications of the power tool. However, if the power tool is used for other applications, the vibration emission value may be different.

WARNING:

  • The vibration emission during the actual use of the power tool can differ from the declared emission value depending on how the tool is used.
  • Be sure to identify safety measures to protect the operator that are based on an estimation of exposure in the actual conditions of use (taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time).

For European countries only EC Declaration of Conformity

Makita declares that the following Machine(s):

Designation of Machine:

  • Cordless Angle Grinder
  • Model No./Type: DGA405, DGA455, DGA505
  • Conforms to the following European Directives: 2006/42/EC
  • They are manufactured under the following standard or standardized documents: EN60745
  • The technical file per 2006/42/EC is available from Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium
    28. 4. 2014

Yasushi Fukaya
Director
Makita, Jan-Baptist Vinkstraat 2, 3070, Belgium

Makita Jan-Baptist Vinkstraat 2, 3070, Belgium Makita Corporation Anjo, Aichi, Japan

www.makita.com.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals