marco Ottomatic Coffeemaker Beverage Systems Owner’s Manual

: June 16, 2024
: marco

Table of Contents

marco Ottomatic Coffeemaker Beverage Systems
Product Information
Product Usage Instructions
FAQ
Quick Start brewing guide
Brewing
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

marco Ottomatic Coffeemaker Beverage Systems

Product Information

Specifications:

Water Level for Full Pot of Coffee: 8 cups
Grind Type: Medium coarse
Holding Temperature with Hot Plate Activated: 165-170 degrees Fahrenheit or 73-65 degrees Celsius
Power: 1100 Watts

Product Usage Instructions

Step 1: Plug In

Place the coffee maker on a level surface and plug it into a wall socket.

Step 2: Prep Cooldown

Allow the coffee maker to cool down for 5 minutes before repeating the brewing process. It is recommended to do this at least two times before brewing with coffee.

Step 3: Grind your Coffee

Grind your favorite whole bean coffee to a medium coarse ground.

Brewing with Hot Plate Activated

Set the switch to the single line I position.
Upon completion of the brew process, the red light will change to a solid white light.
Remove the filter and enjoy your coffee!
The hot plate will automatically shut off after 90 minutes, indicated by the white light blinking.
If you want to reactivate the hot plate for another 90 minutes, move the switch to the O position and then back to the single line I position. The white light will become solid again.

Brewing with Hot Plate Deactivated (for Iced beverages)

Set the switch to the double line II position.
Upon completion of the brew process, the red light will change to a blinking white light.
Remove the filter and enjoy your coffee!

marco-Ottomatic-Coffeemaker-Beverage-Systems-

Tips and Additional Information

Tips:

Solid White Light = Hot Plate on
Blinking White Light = Hot Plate off
Solid Red Light = Brew in process
If the unit is switched to either the I or II position, putting water in the tank will begin the brew process again.
Be sure to use a medium-coarse grind. If the grind is too fine, the water will not filter through fast enough.
Ensure that the appliance is on a level surface to allow proper water release from all holes in the shower head.
Check that the outlet or smart plugs used for the appliance can withstand 1100 Watts.
When making iced beverages, use recipes that specify the amount of ice and water to be used. Less water is needed in the tank as the melting ice compensates for it during brewing.
There may be some residual water left in the bottom of the tank or condensation on the sides. Simply use a cloth to soak up the water or wipe the sides.
The holding temperature of the coffee while the hot plate is activated is 165-170 degrees Fahrenheit or 73-65 degrees Celsius.

Basic Cleaning:

The appliance exterior as well as the tank interior can be wiped down with a warm wet cloth. Ensure that the appliance is unplugged before any cleaning.

Descaling:

To descale and remove calcium buildup in the appliance, use the Coffeemaker Cleaning solution provided in the package. It is recommended to descale a minimum of every three months.

Fill the water tank to the 8 cup level and add in the descaling solution.
Run the brew cycle to fully flush the descaling solution from the appliance.
Run an additional two brew cycles using only water.

FAQ

Q: Where can I find the user manual for the Ottomatic Coffeemaker?

A: You can find the user manual for the Ottomatic Coffeemaker at <https ://manual-hub.com/>.

Q: Where can I find more information about Marco Beverage Systems products?

A: You can find more information about Marco Beverage Systems products at https://www.marcobeveragesystems.com/products/ottomatic- coffeemaker.

We know that you are excited to begin brewing with your CHEMEX® Ottomatic®! Below you will ﬁnd the Quick Start brewing guide:

Quick Start brewing guide

Step 1: Plug In
Place appliance on a level surface and plug machine into a wall socket.
Step 2: Prep
Fill the tank with cold water to the maximum capacity of 8 cups and switch the appliance to the “I” position to allow water to run through into glass CHEMEX® carafe (no coﬀee).
Step 3: Prep Cooldown
Allow appliance to cool down for 5 minutes before repeating process. Do this at least two times before brewing with coﬀee.
Water measurements Use either the cup
measurements on the water tank on the Ottomatic®, or the glass CHEMEX® carafe to measure your water. Be sure not to exceed the capacity of your glass carafe (30oz / 887ml for 6 cup, 40oz / 1.1L for 8 cup).

marco-Ottomatic-Coffeemaker-Beverage-Systems-fig-1

Step 4: Get into the grind
Grind your favorite whole bean coﬀee to a medium coarse ground.
Step 5: The Brew clip
The brew clip provides an additional air channel to prevent slow ﬂow rate. Place the “brew clip” on glass CHEMEX® carafe, opposite side of the pouring spout.
Step 6: Filter up
Open a CHEMEX® Bonded Coﬀee Filter into a cone shape so that one side of the cone has three layers, and place it into the top of the brewer. The thick three- layer portion should cover the pouring spout.
Step 7: The scoop
One rounded tablespoon of ground coﬀee for every 5oz/147ml cup into the ﬁlter cone. Feel free to use more if you prefer it stronger; our CHEMEX® brewing process eliminates bitterness.

marco-Ottomatic-Coffeemaker-Beverage-Systems-fig-2

Brewing

Brewing with Hot Plate Activated
Set switch to single line “I”.
A solid red light will appear below the word “CHEMEX®” found on the base plate. It will remain on throughout the brew process.
Upon completion of the brew process, the red light will change to a solid white light.
Leave glass CHEMEX® carafe in place for another minute or two to allow for all water to ﬁlter through.
Remove ﬁlter, enjoy!
Hot Plate automatically shuts oﬀ after 90 minutes, this is indicated by the white light blinking.
Hot Plate can be reactivated for another 90 minutes by moving the switch to the “O” position and then back to the single line “I” position. The white light will become solid again.

marco-Ottomatic-Coffeemaker-Beverage-Systems-fig-3

Brewing with Hot Plate Deactivated
(This method can be used to make Iced beverages):
Set switch to double line “II”
A solid red light will appear below the word “CHEMEX®” found on the base plate. It will remain on throughout the brew process.
Upon completion of the brew process, the red light will change to a blinking white light.
Leave glass CHEMEX® carafe in place for another minute or two to allow for all water to ﬁlter through.
Remove ﬁlter, enjoy!
Final Step: Enjoy the perfect cup
Pour your freshly made coﬀee into your CHEMEX® mug and indulge in the ﬂavor.

marco-Ottomatic-Coffeemaker-Beverage-Systems-fig-4

Tips

Solid White Light = Hot Plate on
Blinking White Light = Hot Plate oﬀ
Solid Red Light = Brew in process
If the unit is switched to either the “I” or “II” position, putting water in the tank will begin the brew process again.
Be sure to use a medium-coarse grind.
If the grind is too ﬁne, the water will not ﬁlter through fast enough.
Be sure that the appliance is on a level surface, otherwise the water may not release from all of the holes in the shower head.
Be sure that any outlet, or “smart plugs” the appliance is plugged into are able to withstand 1100 Watts.
When making iced beverages, use recipes that specify the amount of ice and water to be used. There will be less water put in the tank because the ice that melts during the brewing process makes up for it.
CHEMEX® measurements for cup size is 5 ounces / 147ml.
There may be some residual water left in the bottom of the tank or condensation which appears on the sides. Simply use a cloth to soak the water up or wipe the sides.
We cannot guarantee the successful use of the CHEMEX® Ottomatic® if it is used with any non CHEMEX® products such as plastic, metal or cloth ﬁlters.
The holding temperature of the coﬀee while the Hot Plate is activated is 165-170 degrees Fahrenheit or 73-65 degrees Celsius.
The largest glass CHEMEX® carafe that can be used in the Ottomatic® is the 8 cup Classic or 8 cup Glass Handle series.
The CHEMEX® Ottomatic® is BPA free and FDA approved.

Basic Cleaning

The glass CHEMEX® carafe should be cleaned using warm soap and water, or placing it securely in the dishwasher. Be sure to remove the wooden collar and rawhide before any cleaning.
The appliance exterior as well as the tank interior can be wiped down with a warm wet cloth. Be sure that the appliance is unplugged before any cleaning.

Descaling:

To “descale” (remove calcium buildup in the appliance), please use the “Coﬀeemaker Cleaning” solution provided in the package. It is recommended to descale a minimum of every three months.