FULL BOAR LT28 Log Lift Table Attachment Instruction Manual

ULL BOAR LT28 Log Lift Table Attachment Instruction Manual

INTRODUCTION

The log lift table attachment can be mounted on the log splitter beam. Easily lift the log from the ground to a position flush with the beam

WARNING entire operator’s manual before media site. using your new unit. Pay attention to all cautions and warnings.

CALIFORNIA PROPOSITION 65 WARNING:

CANCER AND REPRODUCTIVE HARM. WWW.P6EWARNINGS.CA.GOV.

ENVIRONMENTAL

Recycle unwanted materials instead of ry disposing of them as waste. All tools, hoses, and packaging should be resorted, taken to the local recycling center and disposed of in an environmentally safe way.

DISCLAIMER

Manufacturer reserves the right to discontinue, change, and improve its products at any time without notice or obligation to the purchaser. The descriptions and specifications contained in this manual were in effect at printing. Equipment described within this manual may be optional. Some illustrations may not be applicable to your unit.

SUPPORT

Have questions about your FULLBOAR equipment?

Have questions about your FULLBOAR equipment? gofullboar.com, or contact us via your favorite social media site.

SAFETY INSTRUCTION

SIGNAL SAFETY WORDS DEFINITION

The definitions below give the level of severity for each signal word.

DANGER This symbol is used to indicate a hazardous situation which, if not avoided. will result in serious injury or death.

WARNING This symbol points out safety instructions. Read and follow all instructions before attempting to operate this product. Failure to comply with these instructions could result in serious injury or death.

CAUTION This symbol indicates a hazard, which, if not avoided, may result in minor injury, moderate injury, or property damage.

NOTE This information makes the product easier to use.

SYMBOLS

The rating plate on your machine may show symbols. These represent imporzant information about the product or instructions on its use.

WARNING Read and follow the lift table assembly steps and operating instructions in owner’s manual.

WARNING Wrong direction of the log may cause roll and fall when rise.

WARNING Vertical operating position is prohibited when the log lift table attachment is attached.

DANGER Do not sit on the log lift table.

WARNING

When the wedge is extended and not fully return beck, do not pull the control lever outwards, otherwise the log lift table attachment may suddenly drop down risks of falling the log, damage and injury

DANGER Always keep bystanders away at least 10feet (3m) from this machine. Only one person should operate the log splitter and load the logs.

CONTENTS SUPPLIED

Your FULLBOAR log lift table attachment contains the following:

**CAUTION**  Heavy lifting required. Some of the components in these assembly instructions are heavy and can’t be lifted by one person safely. Please plan to assemble this product when another person can be available to help.

1. Log lift table attachment-main table
2. Log lift table attachment-side table
3. Swing Arm
4. Support Leg (left)
5. Support Leg (right)
6. Slide-rail
7. Ejector Rod
8. Bending Plate
9. Log lift table handle (shorter)
10. Cable Fixing Plate
11. Connecting Plate
12. Short Bushing
13. Long Bushing
14. Rotating Shaft
15. Hardware Kit, Including

| M6 x 20| x2 ‘1
---|---|---
| M6 x 25| x 2| 2
| M6 x 20| x1
x 1| 3
| M8x16| x2| 4
| him x 20| x 4|
| m 10 x 60 9.3×70| x 3
x2| 6
| M8 x 20| xl| 7
| 25x20x8 cp 20

_ 5 x 35

| x2
x2
x2| a

ASSEMBLY INSTRUCTION

To assemble your log lift table attachment follow the below instructions.

Preparation

1. Remove the bolt, washers and nut, which connect the wedge with the cylinder. (See Figure 1a.) Keep the removed hardware set aside for later use,
   

2. Push the wedge forward until the wedge completely crosses the log stripper. (See Figure 1b.)
   
   

3. Place a wooden block with a height of about 5.9″ under the cylinder, make ensure the stability of the cylinder and wooden block. (See Figure 1c.)
   
   
   

Ejector Rod Assembly

1. Let the ejector rod go through the fixed uide rail. Align the holes in the stripper. (See Figure 1b.) fiont end of the cjector rod with the holes in the wedge side-shaft. (See Figure 2, illustration 1.)
   

2. Fasten the ejector rod with the wedge side-shaft. (See Figure 2, illustration 2.)
   

Cable Fixing Plate and Cable Assembly

1. Install the cable fixing plate, paying attention to keeping the fixing plate hole in fine with the center of the side spring pin. (See Figure 3a.)
   
   

2. Screw the straight end of the cable into the side spring pin hole. ( See Figure 3b , illustration 1.). Pass \he cable belween (he lower (wo adjusting nuts through the middle hole of the cable fixing plate. (See Figure 3b, illustration 2.). By adjusting the three adjusting nuts, make sure the cable between the side spring pin and the cable fixing plate is just straightened. (See Figure 3b, illustration 3.)
   
   

Handle and Cable Assembly

1. Disassemble the original long control lever (See Figure 4, illustration 1.), assemble the shorter log lift table control lever instead with the same hardware parts (See Figure 4, illustration 2.)
   
   

Cable Holder and Cable Assembly

Secure the cable onto the botiom of the beam via cable holder. (See Figure 5.)

Slide-rail Assembly

1. Pull out the side spring pin and insert the slide-rail through the fixed quide rail until the two bolt holes on the slide-rail are fully exposed. (See Figure 6a.)
   

2. Insert the bending plate into the U-shaped narrow slot of the slide-rail, align the two holes on the bending plate with the two holes on the sliderail, and then tighten them with M8x16 bolts. (See Figure 6b.)

Handle and Cable Assembly

1. Disassemble the original long control lever (See Figure 4, illustration 1.), assemble the shorter log lift table control lever instead with the same hardware parts (See Figure 4, illustration 2.)
   
   

2. Pullthe wedge back. (See Figure 7b.)
   

3. Assemble the wedge and cylinder . (See Figure 7c.)
   

Connecting Plate Assembly

1. Assemble the connecting plate onto the tank, taking care to ensure the correct bending direction of the plate. (See Figure 8.)
   

Main Table & Side Table Assembly

1. Assemble the side table and the main table together to ensure that the hole positions at the connection are aligned. (See Figure 9a, illustration1)
   
   

2. Use ad type pinto insert the right connection hole between the main table and the side table. (See Figure 9b, illustration 2.)

3. Align the front hole of the left support leg with the left connecting hole between the main table and the side table, and fix them with a D type pin. At the same time, align the rear hole of the left leg with the left hole atthe bottom of the main table and then fasten with M10x60 long bolts, washers and nuts. (See Figure 9b, illustration 3.)

4. Assemble the right support leg with the main table. Tighten with bolts, washers and nuts. (See Figure 9b, illustration 4.)
   
   
   

Log Lift Table Attachment Assembly

1. Pass the rotating shalt Through the connecting prate, night support leg long bustang, left support leg, and shart busting in sequence, and finally, wrap it outside the beam pivot pin, then for it on the connecting plate with M9x20 bolts and wadee Figure 10.
   
   

OPERATION

1. When the log lift table attachment is flush with the beam, pull the control lever of the control valve outward while pushing it forward. then the wedge moves forward, and at the same time, the log lift table attachment will go downward. When it lands, release the control lever. (See Figure 13a.)
   

When the log lift table attachment is flush with the beam, pull the control
lever of the control valve outward while pushing it forward. then the wedge
moves forward, and at the same time, the log lift table attachment will

OPERATION

1. When the log lift table attachment is flush with the beam, pull the control lever of the control valve outward while pushing it forward. then the wedge moves forward, and at the same time, the log lift table attachment will go downward. When it lands, release the control lever. (See Figure 13a.)
   

2. Make sure wedge and log lift table stop moving, load the log on the table.

3. Give the control lever a backward thrust, wait until the wedge starts to move, release the control lever, and then the log lift table attachment starts to rise. (See Figure 13b.)
   
   

4. Move the log from log table to the beam.

5. Push the control lever forward, the wedge will go forward to split the log. Give the control lever a backward thrust, then release the lever, the wedge will go back to the start position
   WARNING
   When the wedge is extended and not WARNING fully return back it is prohibited to pull the control lever outwards, otherwise the lift log table attachment may suddenly drop, causing unexpected risks such as falling logo and so on. (See Figure 14.)

6. Repeat the operate from Step 1-5 to complete the log ifting and trainspotting.

PARTS DIAGRAM

PARTS LIST

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>